Pillow block bearing replacement on a worn out McQuay Chilled water Air Handler… Sounded like a jack hammer #hvac #airconditioning #bearing
Пікірлер: 40
@rm202354 ай бұрын
It’s always cool to see how other guys do shaft bearings.
@subcoolHVAC4 ай бұрын
Thanks 👍
@jasonjohnsonHVAC8 ай бұрын
Yeah buddy....those pillowblocks can fight you sometimes. Nicely done bro
@subcoolHVAC8 ай бұрын
You never know until you start throwing some tools at it how hard it will be . Thanks Jason 💪
@MariosACandRefrigeration8 ай бұрын
I was thought to to lock it in the direction of the wheel rotation 13:20,it looked like you tighten cw.but it could be the camera.thanks for posting.
@subcoolHVAC8 ай бұрын
Yeah the set screw was in the shaft key, had to drive it cw , I locked it down like the gorilla before me. Thanks for the comment
@ccthepope8 ай бұрын
I used to think that Mike Lindell was the pillow man, but no more. Yo da pillow man now!
@subcoolHVAC8 ай бұрын
Oh yeah 👍 I guarantee the old pillow would keep you up at night, now I can sleep well 😴
@davidnull55907 ай бұрын
Thank you for the video. You do really nice, efficient work.
@subcoolHVAC7 ай бұрын
Much appreciated 👍
@zekenzy64866 ай бұрын
Great Video. Thank you for sharing.
@subcoolHVAC6 ай бұрын
Thanks for watching!
@topher86348 ай бұрын
Those set screws put up a fight.
@subcoolHVAC8 ай бұрын
Yep, Next step would’ve been drilling out
@topher86348 ай бұрын
@@subcoolHVAC I thought you were gonna have to.
@Ronnocbot6 ай бұрын
The sound of that bearing initially made me think you were running at 50 Hz lol
@subcoolHVAC6 ай бұрын
Definitely was a loud one, Thanks for watching
@maheradous92577 ай бұрын
Very good job.
@subcoolHVAC7 ай бұрын
Thanks for watching!
@EverythingHVACR8 ай бұрын
Gotta love a good fight with a pillow block bearing. Nicely done!
@subcoolHVAC8 ай бұрын
Yep, was a little work out . Thanks Steve 👍
@syedbasheer22998 ай бұрын
💯💯👍
@subcoolHVAC8 ай бұрын
Thanks!!
@dannydaghavarian91858 ай бұрын
awesome job!!! but dont you think lining up the little tags on the VEE belts is showing off :P
@subcoolHVAC8 ай бұрын
Thanks, just showing up to work is all the attention I need 😎
@dannydaghavarian91858 ай бұрын
@@subcoolHVAC love your work mate :)
@vasileiosbakas97548 ай бұрын
Do you know if the pillow block bearings are both the same on the fan housing? Have you ever heard about fixed and floating? i was wondering.. Good job man keep it up!
@subcoolHVAC8 ай бұрын
I replaced the other side prior to this job and it’s the same bearing. I would think fixed are what you find on a motor shaft, is that what you’re asking?
@vasileiosbakas97548 ай бұрын
Yes, didn't remember if the fixed was close to the motor shaft, thx @@subcoolHVAC
@Hwishebak4 ай бұрын
What about the bearing on the backside?
@subcoolHVAC4 ай бұрын
That was replaced 6 months prior
@9ohfiver2 ай бұрын
Did you end up doing the other side too?
@subcoolHVAC2 ай бұрын
Sure did 👍
@9ohfiver2 ай бұрын
@@subcoolHVAC I got an engineered air pillow block to change and I quoted 6hrs for both sides 😩 a part of me regrets it big time
@subcoolHVAC2 ай бұрын
Well the goal is set, you’ll get it done 💪
@l.crossjr7 ай бұрын
Nice! Definitely not your first rodeo
@subcoolHVAC7 ай бұрын
Or my last 🥺Thanks for watching
@georgebrabec17497 ай бұрын
Only one issue, when you shut off the disconnect, would have been nice if you put a LOTO on it. These are training videos and safety is is the best training. Other then that, great job.
@MarcosHVAC8 ай бұрын
Good work, I’ve would’ve gone straight with my bandsaw and angle grinder
@subcoolHVAC8 ай бұрын
The thought was crossing my mind but I had all day if needed this time. Thanks for commenting!