"BLUE MARTIAN" Zac's HOT ROD 1928 Model A RPU Ep.9

Sit down with us, as we check out Zac Park's 1928 Model A Roadster Pickup.
To support Zac, check out his KZbin ‪@WiredCustomsSpeedShop‬
Support the build, by "BLUE MARTIAN" merchandise here:
rodandstyle.co...
HUGE thank you to Millworks Hot Rod, Old Yankee Speed Co, Spotlite Kustom Accessories, Speed and Kulture Magazine, Cheater Slick Culture, Skratch's Garage and Boling Brothers Early Iron
Check us out on our other social media!
⚫ Instagram: / rodandstyle
⚫ Facebook: / rodandstyletv
⚫ Linktree: linktr.ee/roda...
⚫ Our Website: rodandstyle.com/

[@garycamara9955]

The frame is looking good

[@RodandStyleTV]

Thanks for watching!

[@YACYDOODLE]

What a find...my fav new channel

[@WiredCustomsSpeedShop]

Thank you!

[@RodandStyleTV]

Thanks for watching!

[@garycamara9955]

The spring perches need a gusset that goes halfway around the axle and braces the perch. You can tear it off without a gusset.

[@WiredCustomsSpeedShop]

Thanks Gary, I didn’t want to weld them in permanently until I get weight on the car

[@RodandStyleTV]

Thanks for watching!

[@garycamara9955]

The rear kick up looks good.

[@RodandStyleTV]

Thanks!

[@garycamara9955]

That rear end is a 60s chevy rearend. The 55 56 57 had a drop out pumpkin. Looked like a Ford 8" or 9".

[@WiredCustomsSpeedShop]

Serial number on the pumpkin reads 57 Chevy

[@RodandStyleTV]

Thanks for watching!

[@garycamara9955]

Are you going to use a buggy spring in the rear?

[@RodandStyleTV]

Thanks for watching!

[@wismar1971]

Great build man, but should the weight be in the car before welding the rear up? As the frame rails come down with the body/interior/glass weight the centerline of the trans comes down. I could be wrong as I dont do a lot of transverse spring setups. Just a thought. Love the blue martian!

[@WiredCustomsSpeedShop]

Thank you! And thank you for watching! As far as the rear everything is just tac welded in place, it can be cut and moved, I just set it up as a base line, I needed the rear together so I could set up the transmission output shaft angle

[@RodandStyleTV]

Thanks for watching!

[@garycamara9955]

That isn't a 57 chevy rearend if it hasn't got a drop out pumpkin. You just remove the 4 bolts that hold the seal and the backing plates. 5 on 5 is Pontiac or Olds.

[@WiredCustomsSpeedShop]

There might be some confusion in the editing, there has been a 57 rear end in the car, the rear end at the beginning of the video is from a 55 F100, I replaced what was in the car, the Chevy rear was blown

[@RodandStyleTV]

Thanks for watching!

[@garycamara9955]

In the 60s a set of cheater slicks were recaps, they were rarely wider than 8 inches. The widest tires on the 60s were not that wide. If you wanted wide you had to get Indy Racing Tires. There was a guy here tgat recapped racing tires with a street compound. But the tires sais NOT FOR HIGHWAY USE on the side. Wide tires weren't really available until the 70s. Most people used bias ply tires in the 50s and 60s. There were polyglass GT tires in 68 and 69.

[@RodandStyleTV]

Thanks for watching!

[@skratchsgarage]

I’ve owned 8.5 Inglewood recap cheaters from the 60’s. You’re welcome.

[@chuckstith838]

I like watching this build but don't say it's a early East coast 60 build. you started with a East coast 60s build. what's next, disc brake? love watching you but not 60s east coast.

[@garycamara9955]

Actually the radiator goes over the crossmember or behind it. Not in front. Be careful not to get the radiator too far forward. Should be centered on the front wheels.

[@WiredCustomsSpeedShop]

I plan to put the radiator exactly where it was originally when the truck was built as a hotrod in 1957

[@RodandStyleTV]

Thanks for watching!

[@garycamara9955]

Can't you adjust the pinion angle with the radius rods?

[@WiredCustomsSpeedShop]

Yes sir, still needed to get it close to baseline so when the weight is all on the car it’s close

[@RodandStyleTV]

Thanks for watching!

[@joshjahn9028]

Haha!! A day late on watching but once again great content!!

[@WiredCustomsSpeedShop]

Thanks Josh!

[@RodandStyleTV]

Thanks for watching!

[@williamklein1221]

I love the channel and the car. BUT, a traditional hotrod with an automatic trans. No.

[@WiredCustomsSpeedShop]

Thanks for watching William, have you driven a hard channeled car with a clutch? It’s a nightmare

[@williamklein1221]

@@WiredCustomsSpeedShop I have not. But I do have a '26 roadster on a '32 frame that is pretty snug. Flathead and an early Ford trans. So I have a pretty good idea of what it is like. However, it is your car and should be exactly what you want it to be. I have to admit, any hotrod is much better than no hotrod. And yours is pretty special.

[@WiredCustomsSpeedShop]

@@williamklein1221 for sure! Sounds like a cool build! I’m a roadster-alholic haha. I have a 31 roadster with Flathead and 39 transmission that’s super period correct to pre 1950, this one is going to be more driveable than that one, that’s my major plan

[@RodandStyleTV]

Thanks for watching!

[@chuckstith838]

you said you're building a 60 s hotrod. you had that before you started

[@billcampana3471]

That is nOT a 1957 Chevy rear axle. The pumpkin came out the front on a 1957 Chevy.

[@garycamara9955]

I stoped liking alloy wheels on hot rods 30 years ago. Mags make it a street rod. Especially if they aren't period correct

[@WiredCustomsSpeedShop]

Hi Gary, Fenton made their version of this exact style wheel in 1964, craiger version is just much more affordable

[@RodandStyleTV]

Thanks for watching!

[@chuckstith838]

the only thing original is the body

[@RodandStyleTV]

There's more things than just the body. Thanks for watching Chuck!