Nice upgrade! I have the F3X 370mm M-Performance brakes on my E90 330i with custom Brembo yellow calipers and they look and perform great!
@ottowerke Жыл бұрын
I just picked up the same set. Did 370mm rotors and calipers bolt on?
@vysgarage Жыл бұрын
@ottowerke yes
@redmonyelda547417 күн бұрын
Hello, I have put on 370mm in the front bolt on. Now i need to put the back on (345mm). When I ask around, people say that I need the bushings/inserts for the calipers but also ”rear rotor spacer kit (5mm) + spigot rings. I can see that you dont use those?
@vysgarage17 күн бұрын
@@redmonyelda5474 hi If you use e60 rotors, you don’t need spacers, but f30 rotors need rotor spacers. Thanks
@davidcavanaugh6199 Жыл бұрын
Great Video VYS! Thanks so much for all of the clarification on component’s and what models/manufacturers on all the parts.
@robi65189 күн бұрын
Hello, I have a question about this. I have a 2010 325d e91, engine code N57d30a. If I were to install the Brembo 4-piston brake. Could the main brake cylinder handle this type of brake? Thank you in advance for the answers.
@vysgarage9 күн бұрын
@@robi6518 yes, it’s ok
@מדינט6 ай бұрын
Did you had to upgrade the master cylinder or the booster? I own f22 and thinking about doing the same upgrade, I know models with M sport, such as M240i are using different parts.
@vysgarage6 ай бұрын
I didn’t chance the master cylinder. On e9x there’s no need 👍🏻
@BmwM140iClubsport8 күн бұрын
Hi, i’m building a tracktool and want to do the same upgrade, but my question is do you need to code anything after installing it?
@vysgarage7 күн бұрын
@@BmwM140iClubsport hi, no you don’t
@twigg_seventeen631 Жыл бұрын
Good video, informative... However, you bled the caliper the wrong way round! ALWAYS bleed the inner FIRST then the outer
@l3R1CK70P Жыл бұрын
Had exactly the same problem with TOTALLED and RUSTED bold holding the disc on both sides. Ended up by grinding in a notch for a bigest flat bit i got and then slowly beat it out with impact...
@boonenyler3701 Жыл бұрын
Where did you purchase the eccentric bushings for the rear?
@31Raidxns8 ай бұрын
Hey bro quick question, I got new rotors for my e90 they fit but the break callipers can’t fit on because the rotors are vented and too thick.Any ideas what I could do ?
@vysgarage8 ай бұрын
Hi What Caliper and what rotors do you have ?
@Monstero5o7 ай бұрын
Hello, would Bmw f20 m140i front and rears brakes fit on a e90? Would these kit work with them? Sorry English isn’t good.
@axelhollenberger5051Ай бұрын
Will these calipers go on e91 320d 2005?
@vysgarageАй бұрын
@@axelhollenberger5051 yes direct bolt on
@Predrage4 ай бұрын
Im curious can i apply the same setup on the 320d? Mostly asking for the rear, becaues of handbrake?
@vysgarage4 ай бұрын
Yes you can. Here’s the adapter kit: vysgarage.com/shop/ols/products/instalation-kit-for-f3xf2x-calipers-and-rotors-on-e9xe8x
@sr20dett100010 ай бұрын
It would be nice to fit e90 M3 360mm rotors. It will fit under 18" wheels, better cooling design vs 370mm rotors. F80 M3 would require 19" inch wheels.
@tomsky84147 ай бұрын
Great, informative video😉
@Cevium Жыл бұрын
So, you will be having larger rotors in the back?
@vysgarage Жыл бұрын
Yes, that’s how it is on most f2x and f3x cars as well and the Curent setup on my e90 (330mm on the front and 336mm on the rear)
@nevenblaskovic76278 ай бұрын
If this caliper are mounted to e91 pre lci will the pads sensor work?
@vysgarage8 ай бұрын
Yes 👍🏻
@tonytony63092 ай бұрын
are you sure i can swap the calipers on my e87?
@vysgarage2 ай бұрын
@@tonytony6309 yes, dm me
@cwinner6277 Жыл бұрын
One more question, did to remove the filter which is inside of brake reservoir before you put the device which pressurized the system? I could not manage to remove this f**** filter...
@vysgarage Жыл бұрын
No, I didn’t 👍🏻
@E82tue Жыл бұрын
Brilliant video and well edited. I have just finished doing this on my E82 a couple of days ago, So when I saw your hardline come free from the brake hose I cursed you to hell and back(had to replace both mine and what a ball ache that was). Although I guess the stuck disc retaining bolt gave you your share of ball ache, I think I would of just changed the bearing when you snapped the trx bit.
@vysgarage Жыл бұрын
Thanks 😂 My other side was seized solid 😑 Check out how to get around that problem without replacing pipes: kzbin.info/www/bejne/emi6aH6jo6yNZ5Y
@bestiarara Жыл бұрын
did you do both front and rears upgrade?
@vysgarage Жыл бұрын
@@bestiarara yes, there is a video on the channel
@bestiarara Жыл бұрын
@@vysgarage have you ever tried not OEM calipers? Like 335i e9x one that are on autodoc
@vysgarage Жыл бұрын
@@bestiarara I don’t quite see the point …
@samspargo5 ай бұрын
Hey mate I couldn't find the link to the HEL lines on FB could you point me in the right direction? Cheers!
@vysgarage5 ай бұрын
vysgarage.com/
@genemoreno65579 ай бұрын
if i will order the bushings and the bolt how much for them to be ship in Carson CA
@vysgarage9 ай бұрын
Pm me via Facebook please, Curent price is £95
@waqasakram39694 ай бұрын
@VYS how was the pedal feel after this upgrade without changing the master cyclinder
@vysgarage4 ай бұрын
Very good, you’re actually displaying less fluid with new setup.
@cwinner6277 Жыл бұрын
I will change my discs, pads, and brake lines (the front only with OE ones). One question dos I need to start from the RR first, or can I start with the front one when I bleed them?
@vysgarage Жыл бұрын
You can start anywhere 👍🏻
@noelszabo1291 Жыл бұрын
I have a 320i with the smaller rear brake shoe size, could you help me how I can make the handbrake usable with this f chassis brake? or what else should I replace it with?
@vysgarage Жыл бұрын
Hi I supply a kit you use f20 rear setup. Pm me on Facebook or insta
@rlgtim2 ай бұрын
Hey, The break pad wear sensor are the same thing for E90 & F30
@vysgarage2 ай бұрын
@@rlgtim no, plugs are different. Use car specific sensors.
@benripley7596 Жыл бұрын
Are the hell brake lines for an e90 or for the f20? part number or link to what you purchased please thankyou
@vysgarage Жыл бұрын
E90 I have them made to order by Hel, you can buy them through my facebook page with small discount.
@alienware186 ай бұрын
Check that bearing that you torched...
@ricolam49163 ай бұрын
Did you use stock f30 m performance brake line?
@vysgarage3 ай бұрын
Lines are e90 fitment
@enginebreaking6517 Жыл бұрын
I’m on almost the same journey by weird chance. Bought an E90 330i a week ago and have similar plans. I’m confused about the brakes, as I saw someone saying you needed brackets for the fronts but clearly not! Also the bigger rear discs is unusual, are our cars likely to be the same or are there variations of different handbrake shoe sizes? And lastly, where did you get the rear eccentric washers? Cheers and good luck with the rest of it.
@vysgarage Жыл бұрын
Hi, It’s quite common for rear brakes to be slightly larger, my car came with 330mm on the front and 336mm on the rear from factory. Most F chassis cars have 340mm and 345mm front to rear. Your car will definitely have the same rear setup, I make those bushings so feel free to message me through facebook 👍🏻👍🏻
@frankiepontano8647 Жыл бұрын
will this swap work on a 128i? i heard that 335i brakes were swappable so im thinking this may be possible as well
@vysgarage Жыл бұрын
Yes it will work
@corsaturbo1798Ай бұрын
Hello, bolt on ?
@vysgarageАй бұрын
@@corsaturbo1798 yes
@bunker21000 Жыл бұрын
Nice to have all this information. It is the first mod i will do with my F22 . Dont realy know if i can use the same set up as you. Probably have to go with a 40 mm size rear brake caliper
@vysgarage Жыл бұрын
Thanks, On f22 you can go with either 40 or 44
@nihitchavan837510 ай бұрын
What rotors are these? I can only find slotted rotors that are coated black…
@vysgarage10 ай бұрын
Theses are oem, I had them machined
@E90dga Жыл бұрын
Hi. What about brake pad sensor on front? Is it possible somehow to still run him?
@vysgarage Жыл бұрын
Yes, use stock e90
@damiandragon41385 ай бұрын
Did you make the crack yourself, how did you do it?
@vysgarage5 ай бұрын
Care to explain?
@damiandragon41385 ай бұрын
@@vysgarage Yes, I would like to know how to do it, such slotted discs are more expensive than usual, but is there a problem with durability or balance?
@vysgarage5 ай бұрын
@@damiandragon4138 I used a company in uk called Bg developments. Most brake companies will be able to machine any pattern you want.
@damiandragon41385 ай бұрын
@@vysgarage OK, thanks
@Strhitman450AJ Жыл бұрын
Hello. I’m looking to upgrade my front callipers on my E92 325i How did you mount the calliper? Did you have the adapter or does it bolt straight on the car? Thanks
@vysgarage Жыл бұрын
Hi It bolts straight on.
@Strhitman450AJ Жыл бұрын
@@vysgarage thank you. I will be now on the hunt for some callipers. Thank you
@D3humaniz3d Жыл бұрын
Could you give the part numbers for the calipers and rotors? I have my 330XD and would like to beef up my front brakes as well. I'm currently running Brembo pads and drilled rotors which mostly do the job, but I've been looking for a rotor / caliper upgrade anyway. Do these bolt on directly or do you use a distance plate for it to fit?
@vysgarage Жыл бұрын
It’s a direct bolt on, Message me on facebook.
@charlie.m4634 Жыл бұрын
@@vysgaragewhat model are the discs off a f30 ?
@ZomMannerS2 ай бұрын
Can you provided the link for the brake lines in the front
@vysgarage2 ай бұрын
@@ZomMannerS Vysgarage.com
@ZomMannerS2 ай бұрын
@@vysgarage you dont need the installation kit for the front right? and im planning on keeping stock e92 rotors size 348x30 wiill that be fine with the f30 brembos? awesome video btw
@vysgarage2 ай бұрын
@@ZomMannerS no need for adapters but you need f30 rotors. 340x30
@ZomMannerSАй бұрын
@@vysgaragethanks, one last question the new brake line is for the f3x brakes but will fit on the e92? or just new brake lines for e9x and will fit on the brembos
@vysgarageАй бұрын
@@ZomMannerS e9x lines 👍🏻👍🏻
@Reason06849 ай бұрын
Do you happen to have the part number for the calipers?
@vysgarage9 ай бұрын
Message me on facebook
@jayz4dayz237 ай бұрын
Can you use stock 335 rotors in the front? if not what rotors can u use besides f80 rotor
@vysgarage7 ай бұрын
You can’t use e90 or f80 rotors. You should use f30 rotors.
@jayz4dayz237 ай бұрын
@@vysgarage thanks 🙏
@Z-man8768 Жыл бұрын
Do you know what the highest size rotor that can be put on a 128i?
@vysgarage Жыл бұрын
As a straight forward bolt on swap, 370mm is ideal, but really you can go as high as you want if budget and clearance aren’t an issue.
@LuisGonzalez-ph8zp9 ай бұрын
Brake lines are the same?
@vysgarage9 ай бұрын
Yes
@LuisGonzalez-ph8zp8 ай бұрын
@@vysgarage cool thanks for the reply my last question is do I really need the centric bushings? Can’t just swap em out with the bushings they have for the rear calipers
@jaynethell4330 Жыл бұрын
Do you have a part number for the front discs please?
@vysgarage Жыл бұрын
Front 340mm smooth 34116792223 Front 340mm grooved 34106797602 Front 370mm smooth 34106797606 Front 370mm grooved 34106797603
@germancarfan Жыл бұрын
Nice guide thanks, are you using stock backplates up front?
@vysgarage Жыл бұрын
Thanks Yes I am!
@tonykemper889611 ай бұрын
I thought you needed some brackets to adapt the f chassis brakes to a e90? I have a e91 and want to do this conversion
@vysgarage11 ай бұрын
Only rears need adapters 👍🏻
@tonykemper889611 ай бұрын
@@vysgarage your eccentric bushings correct?
@vysgarage11 ай бұрын
@@tonykemper8896 yes
@enore2981 Жыл бұрын
Hello, I will be doing the same with my E92. What brake disc się you use? I see there are bimetal.
@vysgarage Жыл бұрын
Hi Front are original bmw, rear are textar. Thanks
@michaelcondrey8681 Жыл бұрын
did this fit on ur e92 with no problems????
@vysgarage Жыл бұрын
@michaelcondrey8681 yes
@boostedboristheblade Жыл бұрын
So the front is a straight bolt on?
@vysgarage Жыл бұрын
Yes
@jpwilliams5264 Жыл бұрын
I may have missed it but what front rotors?
@vysgarage Жыл бұрын
F chassis 340mm discs 👍🏻
@jpwilliams5264 Жыл бұрын
@@vysgarage is the 370 calipers an option?
@vysgarage Жыл бұрын
Yes, if you use 370/380 Calipers you can use 370mm discs 👍🏻
@YourDaddy-pd8ww10 ай бұрын
what brake rotors and brake lines were used for this mod