Thank you for the info. Haynes manual said not to do this repair yourself, but thanks to this video I managed to get my worn bearing (+140.000 km, so not to bad) out. Now I hope I can replace it and enjoy riding this bike many more kilometers
@jvanschie9422 жыл бұрын
awsome job .rebuilding my 09gsa rear end now 160 klm just in time , had to make the tool as well used a 15/8 deep socket and 1/4 key stock welded around it to create a 10 point ,Thanks again ,There a great bike to work on .Had to replace the trany main shaft as well .
@samianpythag49523 жыл бұрын
I love the method you use to take apart the final drive you almost did all with a hammer and banging the hall thing on the table.
@660awesome3 жыл бұрын
the chalage is to make work it with what you have. is much esier if you have industrial equipment on hands.
@muzaffersar7824 жыл бұрын
Greetings from Turkey. Thank you for this video. My father wants to change his bmw 1200 gs adv’s differential seal but we didn’t. But we change differential seal with this video.
@TheDervMan6 жыл бұрын
Great video, fascinating to see this being done. 👍🏻
@geoham115 жыл бұрын
Excellent video series. Very informative. Thank you 👍
@G4S1113 жыл бұрын
Well done ,will do the same this winter .
@RiojaRoj3 жыл бұрын
I usually put crankcases etc in the oven, much easier. ( PS : while the wifes out shopping !)
@vincentcathy13 жыл бұрын
Hi sir: Can I know where to get the special socket on 6:55~6:59? Thanks a lot!
@alejandrogrisales71515 жыл бұрын
Muchas gracias por compartir ....muy burn trabajo....saludos desde colombia
@JodyTirta4 ай бұрын
Hello, i want to ask where i can buy the bearing for my bmw GSA 2016 k51, because on my country there are no place sell the final drive bearing for my type of gs, please advice if there is some links i can buy. Thanks
@Supernova120343 жыл бұрын
this series has convinced me to not buy a bmw shaft drive motorcycle
@claudiorjsilva5 жыл бұрын
Where can I find this toothy tool to loosen this differential thread lock?
@romiz334 жыл бұрын
posso chiedere dove si compra la bussola per la ghiera del pignone? grazie
@user-vf7gp1hr9c2 ай бұрын
Why can't you use an impact gun on the difficult bolts/nuts?
@thorweldinginnovations61675 жыл бұрын
Great job.
@defossard5 жыл бұрын
Hi, Great video. What operation are you performing starting at 6:25 please
@hartencourt5 жыл бұрын
Just 36000 kms and need change ?!? Thank you 😀
@stuartkidd36244 жыл бұрын
How did you hold the pinion gear to undo the nut I can see you have something going through the centre?
@top_ten20213 жыл бұрын
Hey guy !! Why? Did you replace him?
@Vjekoslav-vf3hr Жыл бұрын
How many km / miles does this bike has for this repair?
@proyecmat3 жыл бұрын
Where did you find the key with the ten teeth to extract the final differential? I can't find it in bmw, could you tell me how you got it?
@660awesome3 жыл бұрын
Tis was laser cut plate 5mm thick and welded to the old 24mm socket . it could be machined on the mill if you have the access BMW special tool cost about 180 pounds it can be found in the parts catalogue.
@oespecialistageneralista79636 жыл бұрын
The needle bearing comes out without removing the pin lock?????
@660awesome6 жыл бұрын
O ESPECIALISTA GENERALISTA Yes don't try to take it out ! I've done another 3 fd after that just need sliding hummer and proper spacer ...
@oespecialistageneralista79636 жыл бұрын
Sorry, but what is the need of that pin if we don´t have to take it out to replace the bearings? Won´t spoil the new bearings when inserting to the correct place with the pin lock there?
@oespecialistageneralista79636 жыл бұрын
I am asking because I am just to replace that needle bearings and the axial bearings of the final drive of my r1200gs adventure, and I am with problems to remove that pin.
@660awesome6 жыл бұрын
O ESPECIALISTA GENERALISTA I found out hard way ! This pin acts like spring loaded retainer and goes in to the grove 0.1mm and when the bearing is forced out pin has enough space to move out of the way ... God luck with your project !
@claudiorjsilva5 жыл бұрын
video .. minute 6:36
@user-zx6ju2eg2w3 жыл бұрын
Не аккуратно молоток рывки на срыве
@stefanmistik1883 Жыл бұрын
Celé zle všetko sa ma nahrievat potom placete ze je znova KO po 10000km