BMW R65 Cafe Racer build - Step 4: Electrical Wiring

[@pmacc3557]

Class job. nice n tidy.

[@yardenl1998]

Nice going! Cant wait for more

[@jimbean4945]

Very nice Ruben. :)

[@BigCammaDeacon]

Very Nice.. I want an EXACT list of what you have on here. I have an 1982 R65 I want to change to this.

[@suitablyimpressed1841]

Excellent thank you...🏴󠁧󠁢󠁥󠁮󠁧󠁿👍

[@didferry3267]

Hi from where di you get the signal to get the RPM ( yellow cable on the tacho) to your daytona speedometer ?

[@johanstam3602]

Hi Ruben. Did you have to replace the tachometer cable? Can't see the new part in the Daytona speedometer kit.

[@saveriomarinelli9109]

Hi, I am modifying the same bike with the Daytona Velona. I would like to know how you connected the tachometer from the bike to the daytona

[@olivermangold5380]

Nice Video. But where did you get the Signal for the N.

[@declinerrexlete197]

Help please! I want to use the 5 spade ign switch like you did and go thru the nacelle/fork ear. Please tell which wires from where goes to each spade. I do know that red goes to #30. Which wires go to #58A, #58E, and #15. Where do I find these wires. The orig ign switch has only 4 wires. Thanks!!!

[@philipcooper8523]

Could you provide more detail on the speedometer installation? Doing similar work on my 1982 BMW R65 and thinking of getting the same Speedometer. Of everything I'm doing, I'm most worried I'll screw up the Speedometer or I'll get one that isn't suitable!

[@LifeofRubbel]

You might find more information in my brother's channel. Also, I think he will make a separate video of the speedometer soon. For now, you can already check out this video of him: kzbin.info/www/bejne/d5bUYoGqg62lgs0

[@philipcooper8523]

Managed to figure it out (Haynes manual finally arriving helped). Following both your channels already as I’m doing similar work just waiting on everything to arrive - only received the Speedo and a few other bits so far

[@christianingemannbentsen3]

Hi Ruben Nice build! I also bought the Daytona Velona but I’m curious about where to get a mount like yours? I like the speedo placed in the center like yours. I’m building a BMW R100, 1982. I really hope you can help. Best Chris

[@spycon69]

Excellent video once again. Do you think it would be difficult for someone with no soldering experience to fit a daytona tachometer into a R45 (1979) ?

[@noelbarsony5968]

How did it go? Did you do the modify?

[@spycon69]

@@noelbarsony5968 yes 🙂 I managed to do it and I am very happy with the results. Next big thing is to fit motogadget m.unit however I thing I will take it to a specialist for that.

[@beuranhendricks4766]

Hi Ruben. Would you know if the Daytona speed sensor would be compatible with an acewell speedometer? Great build 💪🏼

[@LifeofRubbel]

Hi Beuran, to be honest I have no idea. If I were you I would use the Daytona Speedometer, than you are sure it will work.

[@beuranhendricks4766]

Thanks. Did you connect all all speedometer wiring or did you leave out wires that did not pertain to the bike?

[@Mario19900202]

Hello i have a question about the PPR . Does someone know what a r65 -79 have. Is it 1pulse per revolution ore 1 pulse per 2 revolution? I have the Daytona and what it to be correctly programmed.

[@kannsein1137]

How you get the Signal for RPM Daytona,me get Problems with this.

[@jonathanvandermaas2724]

Does it work the same for the K models?

[@LifeofRubbel]

No idea

[@EdFinck]

Where did you find a ignition switch?

[@LifeofRubbel]

I was lucky to find one on Ebay