These Bmw fans wont turn on this way. Which really sucks because I can't even test the new fan and see if I just got 2 bad fans. The plug for the fan gets 12volts all the time, just check for power at the plug. But even after that you have to determine if the signal wire/ecm/sensor has a problem or if the fan is just bad. I gave up BMW's are such a pain in the ass to work on. 😔
@AE-fq4vc4 жыл бұрын
you can't test the fan like that
@aleycat1009 ай бұрын
It's actually feeding through the dme and resistor pack. I'm surprised he doesn't know that. But he's doing a video. This is why other guys get screwed with German cars you need a scan tool and a tester to check these fans properly.
@southbayeurocar28144 жыл бұрын
Fan is control by the DME on control wire by 10 % to 90% of duty cycle. Fan it self has controller in it. There is no relay for BMW X5 fan.
@bpike87933 жыл бұрын
You're absolutely correct. I guess anybody can put up a bad YT DIY.
@RBPD922 жыл бұрын
Of course there is a relay, in the positive side you have a 150amp relay that is located in the wheel mud cover, but you are right, the ECU manage the fan and this video is so bad.
@zekzygaming5128 Жыл бұрын
So basically the control wires turns a transistor in the fan assembly on?
@queenslander954 Жыл бұрын
Cheers mate , this helped with my Z4 .. 👌
@sergiochavez16732 жыл бұрын
From my experience I've taken the fan off my BMW and bench tested it with a 12v battery and just like you tested it it wouldn't turn on, then I went further and tested it at the fan controller on one side, and nothing, then on the other side and it turned on. Moral of the story is try to clean all contact points of wires before saying fan is bad. once all of them are cleaned up it might work.
@lennywebb2743 жыл бұрын
Fan controlled by the DME. The fan could be good and there's a fan activation code stopping it from working
@Yophillips32723 жыл бұрын
Interesting point, but how do you get rid of the code and get the new fan to turn on? Assuming the signal wire isn't bad.
@ninar57355 жыл бұрын
That is not a 2007 E70 X5. It's a E53 X5
@jcmcewen81 Жыл бұрын
Check your fan switch on the bottom radiator hose!
@tuhanpham2 жыл бұрын
That not gonna work, you need to trigger the signal in order for the fan to work.
@johnyq62632 ай бұрын
The coolant fan is possible to test with INPA diag. INPA has direct tool for coolant fan testing. In test check DME temperature of coolant fluid and run coolant fan Adequate to engine temperature. If the engine is cold coolant fan wil be slow if hot it will rotate quickly. For three pins connectors is one wire for impulse control from DME
@nunyadambidness89665 жыл бұрын
You need to do more research. That's not how BMW fans (since 2000) work. The 2 thick wires are + and -, the thin wire is a digital carrier wave from the CPU that activates the fan and controls its speed. Direct current to the fan does nothing.
@Thatguyremy4 жыл бұрын
So then what is the proper way to test it
@peoplepower94154 жыл бұрын
There is a solid state switch in the fan and it gets turned on by a signal from the computer the third small wire
@lindseywebb99534 жыл бұрын
@@Thatguyremy I ran a small wire from the signal wire to fan then hooked up a pos and neg wire. My fan then came on like a air plane propeller.
@danielbaca70684 жыл бұрын
I tested the fan motor same was just connected directly to the 2 wires coming out of the back of the fan. I wanted to test it right off the plug connector like In this video. But I figured I'd research it before I send to many volts in there 😅
@Yophillips32723 жыл бұрын
@@Thatguyremy The only way I can figure is find someone with a similar BMW and plug your fan into their car and see if it works. You can add power to the fan motor itself but that doesn't tell you if the module on the fan is bad or not.
@rodrigojoelecheverriarodri30112 жыл бұрын
And how about the third pin?
@mychannelbannersus Жыл бұрын
That's signal wire controlling speed communicating with ecm, you can't test the BMW fan like that, even good fans won't turn on.
@ElGuti873 жыл бұрын
Sopranos license plates.... NICE!
@seyoneford1 Жыл бұрын
You can test some fans like this but not bmw fans. Maybe older models yes but not these.
@Traveleralsulima2 ай бұрын
Wrongly done, you’re missing out the control signal connectors. It won’t start without it.
@zfloz98953 жыл бұрын
Hahahaha! Disaster tester. :)))
@johnh70642 жыл бұрын
It’s not how you check it the control wire activates the fan
@Bmanfresh4 жыл бұрын
My fan is working but it is stuck on high all the time even with a cold engine where should I start to look for the problem?
@Yophillips32723 жыл бұрын
Probably the coolant temp sensor. But also could be a bad fan. I don't know how to diagnose these things but a coolant sensor is like $20 I would start there.
@aleycat1009 ай бұрын
Thermo switch
@mikesabin8568 Жыл бұрын
This is completely wrong… You have no idea what you are doing or talked about at all.. The giant red wire is power…. From a fuse… The ground is the giant brown.. you said that right.. The small wire is not relays and all that crap you said. It goes directly to the engine module. Supplying voltage to it does nothing.. its a 12 volt square wave low current signal that you can’t duplicate by hand… you check it with a scope. If you have the correct signal from the dme, and your power and ground, then the fan is bad. Terrible video…
@EARTHKEENING Жыл бұрын
My fan keep working non stop on high speed 😢 ?
@EARTHKEENING Жыл бұрын
My fan always kicking on High speed and stay on high speed all day NON stop what should I check ?
@justgosee Жыл бұрын
Coolant temp sensor on lower radiator hose (possibly and from what I've read so far). They say if you unplug it or it's bad that it'll run the fan wide open. I bet that's it for you.
@kendramclemore59785 жыл бұрын
yo bro please get you someone to help out next time....this is very sloppy and shaky....
@ignacioromero50144 жыл бұрын
What a disaster...
@tuhanpham2 жыл бұрын
You hooked up to the battery and you got 14 vAC. Yeah right.
@ruudjes85 жыл бұрын
Latino style esse!
@fernandogarza91804 жыл бұрын
Xray Zulu 🤣🤣🤣
@gavilan8479 ай бұрын
You need a signal wire to trigger activation
@mattpower63995 жыл бұрын
complacently wrong testing ,unplug fan switch (on right side of radiator hose) your fan should work on high speed ,if not your fan is bad.
@Yophillips32723 жыл бұрын
I did that, didn't do crap, but also hooked up a new fan didn't do crap. 🤷♂️