Nice troubleshooting. Glad to see it functioning properly.
@thedelcodave Жыл бұрын
Very excited and it is much easier to operate now
@Texanfirst7274 ай бұрын
Thanks for making this video. My tilt cylinder is drifting on my S175. Hopefully this will recrify the problem.
@thedelcodave4 ай бұрын
@@Texanfirst727 I hope it is a simple fix for you.
@Texanfirst7274 ай бұрын
Was your part 19 called a lock valve or a relief valve? Will you please look in your manual. My bucket drifts down whether operating or in lock mode by lifting the safety bar.
@thedelcodave4 ай бұрын
@@Texanfirst727 part 19 is the port relief. I didn't mess with the lock solenoid as that one was working. Your machine might be slightly different being s175. Look at your manual to see if you have port relief for lift and for tilt and pull them out to inspect. If they are good then you could have a seal in the tilt cylinders leaking internally basically bypassing pressure. I hope that helps
@thedelcodave4 ай бұрын
@@Texanfirst727 also HowIDidit does a KZbin live every Tuesday 6 pm est. You can ask your questions to the real deal bobcat mechanics. Tell them I sent you.
@Texanfirst7274 ай бұрын
@@thedelcodave On the S175, I have tilt port relief valve and tilt circuit lock valve. Tilt cylinders were recently done. They work great, but I do have tilt drift. The tilt bucket drift happens both when operating and when I lock the machine, engine on. I'll look at the tilt port relief valve 1st as it is easier to get to than the tilt circuit lock valve as looking at the manual, the solenoids have to be pulled to get to the tilt circuit lock valve. Thanks for your help!
@Masseyferguson65 Жыл бұрын
Nice feeling for you when you see that bustet o'ring.... and same when you test it 😊😊 She runs great now .. michell norway 😊🚜👍🏻
@thedelcodave Жыл бұрын
It is a great feeling. After going through the cylinders and not finding the "smoking gun" I was disappointed. Seeing that busted o-ring was great.
@tmengelmann2 ай бұрын
Was the front one for the tilt or lift arms?
@thedelcodave2 ай бұрын
@@tmengelmann mine was the lift arms drifting but the same fix would apply to drifting tilt cylinders
@tmengelmann2 ай бұрын
So the one in the rear is the one for the tilt. Correct?
@thedelcodave2 ай бұрын
@@tmengelmann rear should be lift front should be tilt if I recall correctly.
@faridafarida46276 ай бұрын
Hello mister I want to ask my bobcat, the engine starts but won't start and the baket won't move, please provide a solution😊
@thedelcodave6 ай бұрын
@@faridafarida4627 if the engine starts but won't move check your safety switches first.
@faridafarida46276 ай бұрын
@@thedelcodave thanks Mr .. sorry .May I know where the problem is? I'm from Indonesia, hoping for some knowledge from you
@mattmilkie5847 Жыл бұрын
What sized socket was that?
@thedelcodave Жыл бұрын
I don't remember exactly I think it was a 1 inch or 1 1/16.
@MuddFlappRanch Жыл бұрын
Nice fix. I have the same issue with my S185. Hope this fixes it.
@thedelcodave Жыл бұрын
I hope it works for you too. It was an awesome feeling when I saw that blown out oring. Does yours stop drifting if you lift the lap bar?
@MuddFlappRanch Жыл бұрын
@@thedelcodave sure does
@Texanfirst7274 ай бұрын
@@MuddFlappRanch Was it your lock valve or your relief valve that fixed the drifting?
@MuddFlappRanch4 ай бұрын
@@Texanfirst727 I replaced the seals on both of the check valves. Hydraulic Seal Kit, 6690431
@sstocker315 ай бұрын
If I were that far into it I would have change out the O-rings on the other one as well.
@thedelcodave5 ай бұрын
@@sstocker31 I did change the other one off camera