Bosch IXO 3.6V Changing the battery of the charged screwdriver. - Bosch IXO 3.6V Batarya değişimi.

Bosch IXO 3.6V Changing the battery of the charged screwdriver.
Bosch IXO 3.6V Battery renewal.
Bosch IXO 3.6V Şarjlı tornavida pil değişimi.
Şarjlı tornavida batarya değişimi.
Screwdriver battery replacement.
Screwdriver battery change.
Şarjlı tornavida pili
Do It Yourself
DIY Videos
Kendin Yap
#DIY
#Bosch #IXO

[@egmirz1366]

Harika bir işçilik tebrikler

[@ahiskali4720]

Ellerinize sağlık, benimde aynısından var bataryası şimdilik idare ediyor,değiştirmeyi sayenizde öğrenmiş oldum, teşekkürler....

[@doityourself8997]

Teşekkür ederim 🙏

[@julianuzunski5785]

Thank you!

[@robedmunds7163]

Nice, thanks

[@6lr6ak6]

Done good job

[@SgtDreTecKeGamer]

the piece of metal you cut to make the contact -> battery -> wire "what is the metal strip? is it tin, nickle, copper with a silver coating?" I have a skill that is the same size and if I ever need to replace the battery.

[@doityourself8997]

Nickel strip

[@SgtDreTecKeGamer]

@@doityourself8997 thank you very much

[@ritchiesambalod4042]

My Bosch ixo unit is 3.6v it is ok if I change it Sony vtc6 3000mah which is 3.7v sir?

[@HafizurRahman-mw8bp]

How does he know what went wrong without testing and straightaway cutoff battery wire off.

[@doityourself8997]

The screwdriver was used for at least 10 years and the battery started to run out in a short time as a result.

[@user-ti9mr3dt5m]

Did the vtc make it stronger a little more with Newton, or just has a better capacity?

[@doityourself8997]

Yes, the power has not changed. Its capacity has increased.👍👍

[@user-ti9mr3dt5m]

@@doityourself8997 thank you for the quick reply 🙏

[@pash5ful]

You did the process but kindly tell the polarity of battery, every IXO has not followed the same wire color code

[@doityourself8997]

Before removing the old battery, you need to determine the battery polarity. If you forgot, the cable on the edge of the electronic board = CATHODE, the cable inside = ANODE.

[@tomdehouwer1049]

What's the type number of the new accu? Thank you.

[@doityourself8997]

Sony VTC6👍

[@rastom46]

Bendede aynısından var ama sar aletini kaybetmişler nereye gittiysem kaç volt olduğunu sordular uyan hiç bir sarz adaptörü bulamadım yardımcı olurmusunuz

[@doityourself8997]

Orijinal şarj cihazı çıkışı 7V 250ma. Eğer bulabilirseniz, tornavida üzerinde ki vidaya yakın olan taraf artı(+) giriştir. Ama tornavidanın oturacağı yuva uyduramazsanız, tornavidanın üzerine karşılıklı erkek-dişi soket bulup monte edebilirsiniz.

[@dominiqueacanthe166]

Hi dear. I replaced battery with samsung inr18650-30Q SDI 136. But a white smoke came out. Could you please help? Is the battery not appropriate?

[@doityourself8997]

Hello. Where did the smoke come from? Battery or card?

[@dominiqueacanthe166]

@@doityourself8997 from card. I can see that a diode has been burnt. What is the cause please?

[@doityourself8997]

@@dominiqueacanthe166 Are you sure you have polarized the battery correctly?

[@dominiqueacanthe166]

Yes it is correctly polarised. should I increase the diode with a bigger amps as the battery draws 3000mah and still 3.6v?

[@SINA-ck6wy]

nomber transistor?

[@erdanresul7001]

bu modele kaç vlık ir şarj aleti kullanmak gerekiyor

[@doityourself8997]

7.0V, 250mA

[@ideasymoney]

Where can a get a cheap Sony VTC 6 …

[@doityourself8997]

Hi. You can find it from local vendors. If you can't find; You can find 18650 batteries produced by LG, Samsung and Panasonic brands.

[@antoniotorresini812]

Si fanno i tutorial da oltre 10 minuti per sostituire una pila e privi di una stazioncina di saldatura e una basetta con pinze reggi pezzi ... Siamo messi male 😂 peggio degli scappati di casa 😵‍💫

[@friedrichernst6258]

Very dangerous to solder on Lithium batteries! The heat can cause a serious explosion. Wires or zink strips are mostly spot welded, which is very short and does not heat the battery:

[@goldgeologist5320]

It is disgusting that these tools are not made with easily replaceable batteries. Horrible design!

[@jsmithnevinsky]

Creepy slow movements to make the video over 10 minutes. Glad I got ad blocker.

[@stony7827]

bla bla bla