Bosch MSA 25.2 (Mercedes) IMMO OFF | Julie Emulator | CarLabImmo

[@steveaustin9752]

On W210 3.0 TD with MSA 15.1 , Don't forget tu unplug the 2 wire from WSP module (Green and White Wire (CAN H & L)). Mechanic key : No starter motor. Curiously, if WSP Can bus connected, starter motor turn, crank, no start. If WSP disconnected, starter motor don't turn. ECU 0 281 001 230 HW 32.94 SW 33.95

[@h3x.c0d3]

MSA15.1 works ok. Not need connect pin 13 to 12V. Need to cut/remove two CAN wires (green-black & green-brown) located under passenger footwell (black WSP immo module with 2 plugs) /W202 2.5TD/

[@ronniemirar4057]

thank you lord for everything

[@stein-arnefalchpedersen2222]

Good job! Do you know if the MSA 25.1 have the same pinout as 25.2?

[@CarLabImmoTechnicalChannel]

Yes, the pinout for MSA 25.1 and 25.2 is the same.

[@stein-arnefalchpedersen2222]

@@CarLabImmoTechnicalChannel Thank you very much!

[@arvistas]

In this case should I do personalisation of the ecu, like for example with bosh me 2.1 ecu?

[@CarLabImmoTechnicalChannel]

You should do the entire emulator installation procedure based on the instructions, you will find it on page 7: carlabimmo.com/manuals/immobilizers/mercedes/mercedes-4.pdf If the instructions do not mention anything about personalization, it means that it is not required.

[@ajayrao69]

hello i purchased julie emulator pro for mercedes msa15.1 ,need help which pins to short on emulator they are behind the pcb not as shown in this picture ,Thanks ,website link for manual not opening

[@CarLabImmoTechnicalChannel]

Hello. Do you mean which jumpers should be soldered in the emulator? Solder jumpers 3 + 4. See page 7 of this manual for the complete procedure: carlabimmo.com/manuals/immobilizers/mercedes/mercedes-4.pdf

[@ajayrao69]

@@CarLabImmoTechnicalChannel Thanks alot !

[@ajayrao69]

Thanks ! worked perfect ,Excellent Product and support

[@CarLabImmoTechnicalChannel]

IIt's very nice to read such comments! Thank you and we are very happy with satisfied customers! 😊

[@rafaelzinhow97]

I don't have the original file of the B58 memory, I burned the original file while removing it... is it possible to do the immo off with this emulator without the original code of this chip ? I have a MSA 15.1

[@CarLabImmoTechnicalChannel]

Unfortunately, memory reading is necessary because the values from this memory must be entered into the Julie emulator's memory. But if you don't have that memory, make a post on the technical forum, our main technician works there. Describe your problem and maybe he will be able to help you disable the immo in the car in a different way. forum.carlabimmo.com/

[@driftaddict228]

Why I need that can anyone expalne me

[@CarLabImmoTechnicalChannel]

You can use it to replace immobiliser signal :)

[@josephschneider2684]

Does this work for 2005 Chrysler Crossfire?

[@CarLabImmoTechnicalChannel]

We need info about an ECU to answer

[@halimackgoz9518]

W140 S300 turbo dizel immobilizer sistemi ni iptal edebilen varmi

[@CarLabImmoTechnicalChannel]

We need more information like ECU number.

[@lwazidogpriority7178]

Will it work on w202 only cranks

[@CarLabImmoTechnicalChannel]

What is your ECU number?

[@rumanuflorin]

for msa25,2 with 24c04,,works?

[@CarLabImmoTechnicalChannel]

Hello! We always recommend checking the instruction manual. The answer is right there :) Here's the URL to Julie Emulator instruction manual - Mercedes: carlabimmo.com/manuals/immobilizers/mercedes/mercedes-4.pdf (see Page 7 for Bosch MSA25.2)

[@dashtyATG]

Thank you so much for you time Connecting the ECU according to the digram what programmer do you use please. And wher do you get the digram and was it all done on bench?

[@CarLabImmoTechnicalChannel]

We use LabTool 48UXP programmer. You can buy the diagram from Autodata.

[@schwebs68]

Hello, Does it work for w210 2.9td ?

[@CarLabImmoTechnicalChannel]

Hello! Yes, if the ECU is Bosch MSA25.2. Check the instruction manual: carlabimmo.com/manuals/immobilizers/mercedes/mercedes-4.pdf (see Example Car List on Page 11)

[@ильяфедоров-т1ь]

Hello, is this emulator suitable for msa 25.1 ?

[@CarLabImmoTechnicalChannel]

Hi, check instruction manual to find out if Julie supports your car: carlabimmo.com/julie-manual

[@19tuureluur86]

What's the point of doing this? I'm not into tech stuff.

[@CarLabImmoTechnicalChannel]

E.g. if you lost your keys, you don't need to replace many elements like ignition switch, door lock, ECU etc. You can just turn off immobiliser signal with our Emulator (make IMMO OFF) and you can save a lot of money ;)