Bottom End Assembly: Honda XL185s PART 5

[@mattyb7736]

Just found this channel. The 185S (and the 125, and the later 200's ) all had very soft cases and driving bearings into the case was even mentioned in the FSM. You should ALWAYS heat the cases in an oven to 100C 212f until a drop of water dropped in tne case sizzles. Remove and drop the gearbox bearings into place. Tbe crank bosses were strengthened with steel inserts as these were designed to get fitred at room temp. Oh, you had the kick-start spring on backwards, but you worked that out.

[@josephferris6936]

You should get more views you deserve more

[@georgesteffens7489]

Thank you for your time in sharing this project, I love the attention to detail and getting to learn what goes on in that gearbox! Take care!

[@TheMotorcycleMD]

Thanks for stopping by!

[@douglasphillips1203]

I HATED ... how much I enjoyed the video :) . Been a while since I've popped into the channel - love the content man. Keep it up!

[@TheMotorcycleMD]

Hahaha thanks for taking the time man. Means a lot!

[@robertejennings5400]

You do a great job on your videos. Even a non-mechanic like me can keep up.

[@TheMotorcycleMD]

PERFECT! Thank you!

[@Aprilseahorse]

I like to restore, or conserve bikes. The hardware sets are great for bikes that you run alot, but Honda still has most of the hardware new for those that want to keep the factory look.

[@MrNiklas1967]

Lowe your channel . Good tips and no nonsens

[@TheMotorcycleMD]

Thanks man! That means a lot. Thanks for stopping by for the view!

[@gorazorbacks11]

I can’t wait for the next episode!! I’m rebuilding a 185 now and need to see what you do next 😂

[@UKPete]

Great informative video thanks, I might have a go a rebuilding my Honda Transalp 600v in the winter so this boosts the confidence a bit!.

[@TheMotorcycleMD]

Woof thats a big motor! Best of luck!

[@paulaskill3660]

Cracking informative video Cody. Spot on!!

[@TheMotorcycleMD]

Thanks man!

[@rickmartin2154]

Love this. part 6?

[@TheMotorcycleMD]

It’s coming!

[@vermhot]

Great video man !

[@TheMotorcycleMD]

Thanks bro!

[@porchonetwothreefour]

Great video. Very helpful. Thank you.

[@crash86ed]

I'm rebuilding an XR200 which has the main bearings slip fit into the cases similar to this engine. Is it normal for them to drop right in with no additional encouragement? What's to stop them from spinning in the case? Great video, thank you

[@buddybench14]

Sir do you have an available transmission for Honda XL185?

[@ohiohunter4490]

Hey i have a 1995 Honda Shadow VT600 and need to know the float level settings

[@lordofbasement]

08:30 these are brand new bearings??

[@jordanfletcher1173]

I’m having a stutter at low rpm’s when giving throttle it’s a new carb what might be the issue

[@blipco5]

So you put the case halves together with a dry gasket? I can never put a cover on without at least a thin film of non-hardening gasket sealer such as Hylomar. I just can’t. No balls I guess.

[@TheMotorcycleMD]

Hahahaha! Sometimes I do sometimes I don't. I haven't had a case gasket leak on me with or without. The only real benefit I have seen with sealant is that it makes it a heck of alot easier to scrape them back off. Really hope I will not being that anytime soon!

[@jordanfletcher1173]

It’s a 99 Vulcan 800

[@poraniparapeporanipara9829]

Bro no pusiste el empaque de cartón

[@1vincej1]

Hey Cody! I need some carb work for my cb750 nighthawk. 4,000 on the bike. Would you be interested? If so let me know. Bike has a K&N and a Delkevic 4 into 1 exhaust. Stock airbox. So it will need to be jetted. Let me know. I sent you an email week ago. Take care.

[@TheMotorcycleMD]

Hey man, for whatever reason I haven't seen your email? Send it again! Let's talk!

[@1vincej1]

Ok I'll send you an email