A quick demonstration on how to disassemble the tweeter housing to push out dents in the tweeter diaphragm
Пікірлер: 82
@emmettsullivan6902 жыл бұрын
I fixed mine with a handheld vacuum pump and an infant nose cleaner. I cut a section out if the ball area until it fit over the dent like a suction cup and connected the pointed end to the tubing on the pump, applied a small amount of suction and the dome came right back.
@MrMikeej6192 жыл бұрын
Great Video. I just fixed my 684. You just saved me $$. Thank You!!!
@emrelsd9 ай бұрын
Has anyone else tried this method with a pair of 686? The tweeters are not the same but smilar looking ones both models were produced same year..Thank you for the video!!
@_rowjack_47619 ай бұрын
Hi @emrelsd. I actually had a pair of 686’s as presence speakers a long time ago. I would hazard a guess that they’d come apart in much the same way. I believe the tweeter is the same, but the aluminium badge and the plastic behind it is just slightly shorter in length.
@irelmo695 жыл бұрын
I feel your pain! I had my 2 fronts and the centre done in one go and 2 weeks later the centre was pushed in again! My kids are now a bit more grown up so now I'm going to repair if possible but replace again if not.
@TheSpoolin77 Жыл бұрын
I got a set of 800 Nautilus from a guy and one of the tweeters on the sc1 was dented. Ordered a new one from B&W parts and started to take on the repair. Once apart I basically did what you did but I found using a phone or tablet rubber tipped stylus worked magic. Give that a try for the people wanting to attempt this delicAte form of paintless dent removal. 😁
@mattiasclaesson88853 жыл бұрын
Great video, thank you. Tried it on my CM7, a bit different tweeter but the same method worked, thanks!
@garypranzo93343 жыл бұрын
In a cool environment (Under 74F) 1. Blow dryer 2. Clear packing tape. 3. Heat the tape not the tweeter 4. Place over dent trying to make contact inside crater 5. Go do something else for an hour or so 6. Put a finger gently on a non damaged part to hold dome so you do not pull dome out 7. Lift carefully straight up but this is where what you do next will vary (Sometimes angling it a bit will help here and sometimes not) At best and If you are lucky the dent will come up perfectly but it will leave a faint discoloration where the dent was. At worst you will get the dent out but it will bumpy in the dent area. I add this because not every BW tweeter dome can be accessed this way. The bottom line is BW took way to long to address this and add tweeter grills.
@lucbeauvais18473 жыл бұрын
You are a life saver thank you so much!
@christianrungstedandersson33373 жыл бұрын
Thank you. This was really helpful!
@fredgien6 ай бұрын
Show also how you put everything back together!
@leebufton2 жыл бұрын
Cheers bud.. Saved me 100 bucks 🍻👍
@steadysteadyed6 жыл бұрын
Fantastic vid and thanks for saving me a few quid. Champion.
@janinefranks24614 жыл бұрын
brill, thanks , good strep by step. bean handy to show removal of main speaker!.cheers
@segervind4 жыл бұрын
Thx!!! Great video and just saved me a couple of bucks! Thx!!
@h3h3umm5 жыл бұрын
exactly what I was needing
@KingKongMartBob2 жыл бұрын
Vacuum didn't work for me. This is an easy repair with that video. Thanks.
@DrEmstri8 ай бұрын
Hi excellent video! I know this is an old video so crossing my fingers for an answer. How is the diaphragm itself attached to the plastic frame? Glue? What kind of glue is apropriate for this? And how do I safely remove it? Many thanx 🙏
@_rowjack_47618 ай бұрын
Hi. It was glued to the diaphragm. I had an old tweeter completely apart a year ago (although didn’t video it). I googled the same question at the time and deduced it was either cyanoacrylate or epoxy. I assumed that being B&W they’d use cyanoacrylate and so I used nail polish remover. That loosened it substantially and I was able to fully and cleanly remove the rest with a craft knife. I didn’t put it back together, but if I had, I would use cyanoacrylate. Only because I absolutely hate using epoxy 😂 Hope this is helpful.
@DrEmstri8 ай бұрын
Thank you for replying 🙏 I got a pair of 684 S1 yesterday with one damaged diaphragm. Figured I will try and replace it myself as soon as I can source one of decent quality. 😊 Job seems a bit fiddly but pretty straight forward. Maybe I'll even record it.
@jonpatrick664 жыл бұрын
Good job! Thanks for the instruction!
@moribass51604 жыл бұрын
Thanks for the instruction!
@divscuba70963 жыл бұрын
Would be great to see a vid of replacing just the dome! As you cam get spares of these
@_rowjack_47613 жыл бұрын
I'm sure I have an old one kicking around somewhere. I'll see if I can dig it out in the garage tomorrow and will link a video if I still have it.
@divscuba70963 жыл бұрын
@@_rowjack_4761 ok brilliant. I have just purchased two domes from ebay for my 684s... ibe followed your video to get this far but a little nervous to remove/ unglue the actual dome! Thanks
@divscuba70963 жыл бұрын
@@_rowjack_4761 did u have any luck ?
@kleber19716 жыл бұрын
Very good. Thanks was very helpful
@angelos8083 жыл бұрын
thank you, it worked!!!
@utube321piotr Жыл бұрын
Great job.
@peterku83745 жыл бұрын
Thank you! Good work
@johnsweda29994 жыл бұрын
In the chamber behind the speaker put some natural wool alpaca wool or or rabbit wool pack it in about an inch
@_rowjack_47614 жыл бұрын
I'm intrigued. What does that do for it?
@johnsweda29994 жыл бұрын
@@_rowjack_4761 well comes down residence in the diaphragm stop back reflections as well. Should make the tweeter sound sweeter and have better time delay
@Tangyorangutan4 жыл бұрын
Hey Frankie thanks for this video! I have a 686 and it looks like that little plastic cone on the back of the tweeter is broken off. Should I re-attach it or is it unnecessary?
@_rowjack_47614 жыл бұрын
I would definitely reattach it. I can't say for sure but it looks as though its there to dampen vibrations and probably helps prevent the tweeter sounding tinny.
@Tangyorangutan4 жыл бұрын
@@_rowjack_4761 Thanks a lot!
@spacescraper20094 жыл бұрын
@@Tangyorangutan @Frankie Howard would you use glue or a high adhese double sided tape please to attach the plastic cone? ive had this happen also and wondering what to use and how attached it needs to be :) thank you
@Tangyorangutan4 жыл бұрын
@@spacescraper2009 I used glue! I can't remember exactly what type (epoxy/wood glue, perhaps JB Weld) but I applied the glue, re-attached the cone, and placed it upright on a soft towel (or any soft surface to protect the tweeter) and let it dry overnight.
@LLS19784 жыл бұрын
Thanks a lot for this! 👍 My buddy has the same tweeters in his speakers I think. But his tweeters has holes in the diaphrams. Does anybody know if these can be replaced or we will have to get all new tweeters?
@brodiehaward3 жыл бұрын
If you call b&w I believe you can order just the dome/diaphragm. I am not sure if they send it assembled with the plastic plate and the terminals, or with just the dome coil and bare leads. I believe you get the dome and have to attach it to your original plastic plate with terminal connections. I have found b&w very helpful and willing to sell you parts no questions asked.
@vietenthuse3 жыл бұрын
I just purchased a new tweeter. It was relatively cheap.
@myplaguesify3 жыл бұрын
very informative
@-SDegirmenci4 жыл бұрын
Thank you 👏
@user-ig6se9in1t3 жыл бұрын
Спасибо Большое за обзор!!!
@madcowcomputer94926 жыл бұрын
Does anyone know how to replace B&W Bass Unit Kevlar for " B&W Signature 30 Speaker ! How to remove the Silver Cone Ring that block the Bass Unit Kevlar! Any Video have ???
@raymondleggs55086 жыл бұрын
Have you tried parts express for an equivelant?
@djzonk13 жыл бұрын
Are this tweeters similar between cm1’ ?
@Thiago_TS_BR7 ай бұрын
Im with the same problem.
@jopyvandermaas23274 жыл бұрын
Just did my HTM62 ....
@_rowjack_47614 жыл бұрын
I miss my HTM62. I upgraded my speakers recently and sold is part of a package. But I do miss it. Great sounding centre.
@jopyvandermaas23274 жыл бұрын
I bought mine back plus my 684's after selling them to a mate a few years ago....happy joy...:-)
@divscuba70963 жыл бұрын
Are tweeters exactly the same for 683 684 685 ? They look very similar
@_rowjack_47613 жыл бұрын
The tweeter is the same but the silver oval name plate part is a different size for each
@aathiworld9 ай бұрын
Can you please tell me How many ohms are they
@_rowjack_47619 ай бұрын
I’m sorry, but I don’t know that.
@aathiworld9 ай бұрын
it’s ok . Thank you
@danielcave96066 жыл бұрын
How did you get the other speakers out first? From the front or back. I can't see any access points.
@jamescollins60856 жыл бұрын
You need to pop off the plastic facade from the midrange driver, behind you will find 8 screws. He goes over this in the video here: 00:35
@danielcave96066 жыл бұрын
Cheers James, A bit more assurance on how to do that would be super handy. I REALLY dont want to damage my super nice speakers. I did try sticking in a very small screw driver to pull the housing forward but i didn't have the cahones to give it a heavy handed attack.
@jamesehoey5 жыл бұрын
I had the same worries but then just gave it a go and it popped out fairly easily
@jamesehoey5 жыл бұрын
Daniel Cave go for it... it’ll be fine...
@PrestonSuperCarMeet4 жыл бұрын
@@danielcave9606 kzbin.info/www/bejne/jGbFaJWud9mNm8k For future reference. Very similar routine.
@Drakesy3 жыл бұрын
or take out a vacuum cleaner and place it on the tweeter. Magic.
@_rowjack_47613 жыл бұрын
Tried with the Dyson. Didn't work. It would have left horrible creases in the metal if it did, too.
@PawelLeszczynskipav3 жыл бұрын
Where did you get the replacement tweeter? Are you based in UK?
@DickCheeseman3 жыл бұрын
It’s not a replacement, he repaired the dent before making the video
@PawelLeszczynskipav3 жыл бұрын
@@DickCheeseman hi did say at the end of the video that it's his 3rd tweeter and he's fed up of spending money on it each time. Mine is beyond repair that's why I'm trying to source the part.
@DickCheeseman3 жыл бұрын
@@PawelLeszczynskipav Try ebay
@PawelLeszczynskipav3 жыл бұрын
@@DickCheeseman I've had a search notification set up with them for a while, but thanks.
@joefriday13206 жыл бұрын
My B&W 683 tweeter replacement part came without the plastic housing part with foam material on the back of the tweeter. At the base of the plastic housing are threads for the plastic ring to secure the tweeter in the speaker box. So, I need to remove this housing part from my old one with the broken tweeter dome and reattach it to my new tweeter replacement part. What do I need to do to remove this part without breaking it and attach it to my new one? Is this housing part held in place using some sort of a super glue? Any ideas?
@_rowjack_47616 жыл бұрын
Joe Friday Did you buy direct from B&W? If you did you should send it back and ask for a full replacement. If not, I have an old tweeter here. Give me an hour to run an errand and i'll get it out and take a look for you.
@valsoundsystem88056 жыл бұрын
É domo titânio amigo ?
@bigstick52785 жыл бұрын
A dented dome would have been a good example. You will still have small bends in the metal wont completely be smooth.
@_rowjack_47615 жыл бұрын
Oh, for sure. But it'll be a heck of a lot prettier to look at. Unless you're a computer, you won't notice any difference in sound quality either. I only thought to record this video for people after I'd smoothed out the dent and realised how much of a pain in the neck it is to do.
@vredewold3 жыл бұрын
Use the vacuumcleaner, to get the dent to pop out.But be careful. do not disassemble
@_rowjack_47613 жыл бұрын
Didn't work with a Dyson.
@garypranzo93343 жыл бұрын
Will work if you are lucky or you might suck the dome out of the speaker. These are not like other tweeter domes and do not respond to suction in the same way.
@daftmoonz93956 жыл бұрын
Just don't dent the tweeter of the 800 D it's dome is made of diamond.