Briggs and Stratton STARTER MOTOR ~ FIX or REPLACE? HOW TO REPAIR common PROBLEM wont work

No video

Briggs and Stratton STARTER MOTOR ~ FIX or REPLACE? HOW TO REPAIR common PROBLEM wont work

Рет қаралды 38,008

Күн бұрын

Briggs and Stratton STARTER MOTOR ~ FIX or REPLACE? HOW TO REPAIR common PROBLEM when wont START won't work will not SPIN freely, rust . 8 Horsepower FLATHEAD style model riding lawnmower engine. Sat outside too long storage RUSTED UP WONT SPIN FREELY . take it apart clean bushings , shafts , armature , brushes lube and reassemble. Electric start Stopped working .........
Remove starter flywheel carb carburetor muffler stripped bolt head gasket rebuild resto restoration fix repair run start gear work which where does why lawn yard mower lawn parts puller tool tools removal adjust adjustment gas model start won't will not run dont doesnt battery amp discharge dead drain too much take put on off Review thoughts tips advice troubleshoot why carb carburetor clean piston valves spec tell specification capacity much gas fuel belt motor model choke fuel spark capacity oil why when will not where what shows spark whats diagnose service inspect check tank solenoid watch easy way which replace does can dies stalls compression parts diagram Craftsman 917. restore piston cylinder valves charge sears broke MTD Poulan adjust adjustment Yard Machines koler kohler tecumseh briggs and stratton straten over winter rust rusty voltage stratten John Jon Deere Deer Scott's Scotts Cub Cadet Toro troy-bilt troybilt Troybuilt troy built bilt Ariens rider tool tools Jonsered ohv intek single twin Gravely Snapper Hayter Lawnboy Mountfield lowes home depot walmart seafoam grip tools will it run work turn over flathead rebuild turbo cool lawn mower repair small service oil gas spark compression turnover turn over how to
Copyright 2021 Jeff's Little Engine Service
Music by BonzaiRod
Donations are greatly appreciated!
Donations can be made by clicking on the link below
www.paypal.com...
PLEASE KEEP IN MIND when you are watching my videos: I am showing you the least expensive, quickest "backyard" methods for repairing or servicing your lawnmower or equipment. Replacing all components such as gaskets and fuel lines is always recommended when rebuilding or repairing equipment. With these videos I hope you are able to fix and repair your lawnmower yourself with minimal parts, knowledge and tools. Thank you for watching!

Пікірлер: 32

@tcmusic_thomas_upton 2 жыл бұрын

I appreciate the honest and straightforward methodology to do a repair. I might suggest using "match marks" to assure proper re-alignment. Also, it is a good practice to use a wooden block to support the shaft to remove the roll pin.

@JeffsLittleEngineService 2 жыл бұрын

Great tips!

@sinabagherisarvestani8924 2 жыл бұрын

@@JeffsLittleEngineService I'm missing one of the the long screws so its loose and its leaking oil ?? So my tractor won't start , I'm not sure if its a weak battery or the loose starter , would a start with only 1 screw be a issue ? the start engages but it too slow and too weak to start the engine it rotates than stops than rotates slowly than stops ????

@lawrencecarroll2031 3 жыл бұрын

I made 2 clips, U shaped, about 1 and 1/4" long with 1/2" legs and i just stick them thru the bottom of the starter to hold brushes back, then assemble starter and pull them out. I made them out of a wire coat hanger.

@jimdwyer4706 Жыл бұрын

Can you convert a c clip pin to a the old style roll pin?

@lawrencecarroll2031 Жыл бұрын

@@jimdwyer4706 I don't think so; at least not without drilling a hole in the starter shaft to accomodate the pin.

@paulmonk7820 3 ай бұрын

Use a piece of cardboard to hold the brushes in place while you install the armature into the end cap 😀

@paulmonk7820 3 ай бұрын

To make installing the bolts easier , put a rod, or whatever fits, through the case into the holes in the commutator end. Then, remove one rod and replace it with the screw. Then do the other one.😊

@rickbroerman9267 3 жыл бұрын

I Love that video..I learned quite a lot. Thank you!!

@JeffsLittleEngineService 3 жыл бұрын

Glad it was helpful!

@mr1pearl 3 жыл бұрын

You know I would have never tried this before now Thanks man ! 👍

@leonwatts6134 2 жыл бұрын

i had a slow to start mower i just checked the starter motor and the internal magnets had broke loose on two of the four so i cleaned them up with metho and used some loctite 620 high strength sleeve retaining compound to glue them back to the body atleast being magnetic they hold them selves in place while they dry ill let u know how it worked out tomorrow when it dries out hopefully none gets into the bottom bush haha

@fred306801 3 жыл бұрын

Got mine pulled apart just like you did in the video. Looked into the cylinder at the magnets. One side of the magnets are all cracked up and a chunk of magnet is missing. Got some light in there so I could see, looks like the armature has rubbed up on the magnets, I can see gouge's. It is kind of funny most of the time this mower would start up. After it ran awhile then I shut it off. It acted liked like the battery was about dead, and it was New. It had a hard time turning over. I am guessing this is the reason. I started screwing around with it because the hot wire that hooks to the starter it was just dangling loose. Looks as if someone did not use two wrenches to take the starter off and pulled the hot wire out of that plastic peace that holds the brushes. Well what do you expect it is a used mower.

@Alpha1545 3 жыл бұрын

What he said. Use a couple of popsicle sticks hold the brushes drop the armature pull out the sticks. You already know that as soon as you put that back together the magnets will pull it loose. Good job anyway. Always nice to have an extra starter on the shelf.

@JeffsLittleEngineService 3 жыл бұрын

Great tip! I tried quite a few diferent ways before I was finally able to get it together

@luisarturogarciaarmijo9117 Жыл бұрын

Excelente 👍

@JeffsLittleEngineService Жыл бұрын

gracias amigo!

@luisarturogarciaarmijo9117 Жыл бұрын

@@JeffsLittleEngineService Gracias a Usted También 😀👍

@heffedirte6243 Жыл бұрын

Cleaning and lubing the far end of the bolts before manhandling the skinny bolts may lessen the chances of breaking them? I'm just guessing....try it out

@ohyeah3750 11 ай бұрын

I've seen many briggs starters, but never one like that.

@JeffsLittleEngineService 11 ай бұрын

It's an old one off a 8 hp vertical engine

@BallBusta Жыл бұрын

I have a 925-06300 Electric Starter and there's no roll pin in the top assembly. I can't afford to replace the whole starter (it's like $174.00), so I need some help seeing I can salvage it. Any tips on removing that sucker?