Briggs & Stratton Carburetor Rebuild - Full Version Small Engine Fix 5HP

[@Buckwsr]

Carburetor Kit Stens 520-522: amzn.to/2PUOSna

[@1973mre]

You failed to go through the linkages and that’s what I’m having trouble with especially with a spring on the bottom of the tank

[@AlloyedFrequencies]

Thank you

[@mjb12141963]

I have this same engine on a chipper/shredder that is doing the exact same thing. Now I feel more confident about my diagnosis. Thank you for doing this video.

[@Buckwsr]

Thanks for watching and commenting. Made my day! Good luck!

[@askinggrandpa418]

Thanks for the video save me I don't know what I did if you hadn't had your videos

[@michaeldestories3412]

Thanks man huge help! Rebuilding the carb on my Craftsman 5 hp compressor.

[@Buckwsr]

Great job. Thanks for the note!

[@BigBuckGetter]

Great information. A tripod would not interrupt you while you are filming a video.

[@edstimator1]

Great photography! You work on that and I'll check back in a few months

[@Buckwsr]

+edstimator1 Thanks, Ed. How will I know when you've checked back in?

[@edstimator1]

When you see my monnicker next to an attached message!

[@Buckwsr]

edstimator1 Ok, great. Looking forward to it.

[@roystheboy]

some ome has just brought a rotavator with the same engine where it wil fire if you spray fuel in the carb but cuts out straight away ive also noticed a spring come off between the fuel tank and recoil cover i think for the governor but it dont seem to fit correct

[@wallacetom1]

Any ideas on why my 5 hp B&S engine will not start after cleaning an new carb kit lnstallation . I have to use starter fluid to get it to run. Once it starts it runs great.Pulled the carb for a second look and cleaning. New fuel pickup tube installed with no trash ariund filter.

[@pb4585]

What about the main jet, did you take it out and clean it?

[@mphowington]

This is helpful, I stumbled on it in replacing my carb on a similar model. do you have a picture or a diagram on how to put the rods back on (throttle)- I was not paying attention when I disassembled, and have it all ready to go but... cant remember what rods go and attach where and in what order!

[@Buckwsr]

Well, this repair was a long time ago, and I no longer have the machine. So I can't help you there. You probably thought of this afterwards...."I should have taken a photo before disassembly."

[@mphowington]

Well why yes I did! I was helping my wife with dialysis and focussed on the bolts so I wasnt paying attention. Any ideas where to find diagrams or could I send you a picture and you help me? This should be a no brainer (its mostly the throttle linkage in struggling with)

[@Buckwsr]

@@mphowington I might be able to help. Give me the make and model of the machine. Also, the Briggs and Stratton engine information that is probably stamped into the engine cover somewhere.

[@mphowington]

Great! The machine is 917292403, craftsman tiller. Engine is 134202-1118-e1- i ended up with a new carb and mostly cant figure out how to connect the throttle linkage (link to crank bell and confused myself with the governor and speed control rods) basically what connects the throttle lever - id be happy to email you pictures- my diagram doesnt really show what connects where.

[@Buckwsr]

@@mphowington Sorry, I've been maxed out lately and haven't been able to do any research for you. Have you made any progress?

[@majestical5331]

I have a tiller that the in tank fuel bowl (short tube) isn't filling. Filled it and reinstalled and it ran for a few. Supposing the worn diaphragm is the cause?

[@Buckwsr]

sounds like the pump built-in to the carburetor isn't sucking gas up from the tank. A rebuild kit should resolve that.

[@majestical5331]

@@Buckwsr Thanks! Spent 2 hours trying to start it doing everything. Finally saw that bowl at carb disassembly and had a eureka moment..

[@nancybednar8665]

Really liked the video especially the ladies questions I asked the same thing right On

[@Buckwsr]

Yes, she's a nice lady....also named Nancy, by the way.

[@melodymccallister8671]

Where would I get a butterfly Rod connection the plastic at the end of my just busted

[@Buckwsr]

Use your engine model number to go online and look up parts for that particular engine and carburetor. Another option would be to get an inexpensive (made in china) aftermarket replacement carburetor.

[@melodymccallister8671]

Thank you you have a blessed day

[@stevenengster1294]

I have the same exact machine. It starts but I can not move the choke past half way before it stalls out. I just replaced all the gaskets and the belt. Do you think it needs a rebuild or do you think the diaphragm could be bad or is there a blockage somewhere. I have tried to adjust the needle and the throttle screw with no luck. I would appreciate any help you could give. Thanks

[@Buckwsr]

If it only runs with the engine choked, then you're not getting enough fuel through the carburetor. A rebuild and thorough cleaning would probably do the trick, in my opinion.

[@dandrag1]

Awesome. Thank you!

[@jasond.606]

LOL ! If you would have watched my other segments . That'll get you plenty of hugs and kisses from your other half lol .

[@nicolabooth6075]

Did you remove and clean the main jet?

[@Buckwsr]

Honestly I can't remember. I did this video like 2 years ago. I guess if I did not show that in the video, maybe I didn't remove and clean the jet.... most rebuild kits include the parts to do so....

[@jasonsmith1702]

Thank you.

[@hadleymanmusic]

I just received a carb offa Amazon now I'm at odds before making a disaster.

[@SneakerGoodsMiamiTV]

In need of a 5hp motor for a go kart I'm building from scratch. Are you selling the motor by any chance?

[@Buckwsr]

Sorry, I sold this machine. Already. Keep looking. You'll find one!

[@SneakerGoodsMiamiTV]

I been looking forever for a decent one trust me. If you ever come across any let me know

[@Buckwsr]

I sure will.

[@SneakerGoodsMiamiTV]

Buckwsr thanks

[@paulthornton2070]

Wh ole you were in there you should have pulled the valve seat out and cleaned it also.

[@philliphall5198]

I AllWAYS remove tanks and clean them with white vinegar It’s just the right way to do it

[@mgomez5606]

They should of put plastic tank on it instead of metal.

[@seansullivan4087]

Thumb nail?

[@Buckwsr]

Yes. I have one on each hand.