Sort of went through this my old td5...... After ripping everything appart...it was a KIN bonnet hinge squealing 😂
@angusabbott561522 күн бұрын
Thanks for sharing your battle with this particular 300 TDi
@BritannicaRestorations22 күн бұрын
No problem 👍
@SteveJones-k5u22 күн бұрын
Had a similar noise on a VW TDI it turned out to be a hair line crack in the cam shaft hub centre from the woodruff key locating slot , good luck , you have the patience of a saint and very thurough.
@BritannicaRestorations21 күн бұрын
Thanks for sharing!
@kevinrowlands675322 күн бұрын
Mike you are realy thourgh and patient
@BritannicaRestorations21 күн бұрын
Have to be - there is no-one to back heel this onto!
@paulholland541222 күн бұрын
Mike I really hope you're onto some think with the pump timing. I once had a squeak that from the cab sounded like it was behind speedo but upon further investigation seemed to be coming from the injector pump area, All I did was replace the diesel filter and never heard it again, that was several years ago and still going strong.
@BritannicaRestorations21 күн бұрын
See next video!
@jameskerr575621 күн бұрын
Hope you get to the bottom of the issue. Very patient to strip it all down. Think I might be reaching for the Jamesons
@BritannicaRestorations21 күн бұрын
Getting close now!
@malcolmyoung786622 күн бұрын
No clue as to the weird noise but VE Pump timing has almost been my nemesis. Not one of the Land Rover things but a VW iteration(well Bosch for VW) that has an electric governor instead of a mechanical thing. If it’s not on the button regards dial gauge adjustment it just won’t start.surprised that the pump you have actually ran at all. Maybe that’s the tolerances Land Rovers are renowned for.. Meanwhile I struggle on to time my pump just to get it to run so I can adjust it so it runs correctly. It’s been a long process and much advice sought(along with completely incorrect info from a manual/specific to my van) but KZbin is helping me out in that regards.. always thought Land Rover VE pumps were easy to time up.. mine I has been complete twa7!!
@BritannicaRestorations21 күн бұрын
Says in the 300Tdi specs for an EDC pump, the lift is only 0.45mm at TDC
@GrumpsBarn22 күн бұрын
My only suggestion is to check the air filter strap cotton reels, had a knackered one once that made a weird squeaking noise that went with the revs
@BritannicaRestorations21 күн бұрын
See next video!
@ScR-jb7th22 күн бұрын
I once had a similar noise at a similar frequency, although mine was more of a whistle. Turned out to be a cracked glow plug, the noise was combustion gas whistling through a crack that was so small you couldn't see it. So it might be worth changing the glow plugs.
@stephenbricolman106722 күн бұрын
That was my thought on the second video 👍
@BritannicaRestorations21 күн бұрын
See next video!
@leaulife56922 күн бұрын
Just give it some millet and a cuttle fish bone and it`ll be fine.🤣
@BritannicaRestorations21 күн бұрын
Lol!
@bradhardwidge152122 күн бұрын
The noise has gone because airfilter housing removed. It's the rubber mountings underneath that have gone and it's metal against metal.
@BritannicaRestorations21 күн бұрын
Don't think so...
@mickdavis852122 күн бұрын
Check the mounts on the intercooler
@BritannicaRestorations21 күн бұрын
Not that...
@justjames838322 күн бұрын
It may have already been suggested or checked but if it's a squeaking I think I might be tempted to check the blue hoses and make sure they're not rubbing on something or each other
@BritannicaRestorations21 күн бұрын
See next video!
@kinnellian22 күн бұрын
You have the patience of a saint I have to say, I'd have been raging long ago. Compelling stuff. I know you're ruling out the vacuum pump, but I kinda thought it could be peripherally related somehow, because the pitch of the "chirping" changed quite noticeably lower when the vacuum pump was removed last video. Be buggered if I can think how it can be related though.
@BritannicaRestorations21 күн бұрын
See next video!
@erictyrrell356022 күн бұрын
Schrödinger’s squeak
@BritannicaRestorations21 күн бұрын
lol!
@simonrowlands747222 күн бұрын
Check the idler bearing in the timing belt cover, strange one
@BritannicaRestorations21 күн бұрын
Changed already..
@graham-martin584722 күн бұрын
this might be a long shot have you checked inside the water pump incase there is something in there catching the impella ?
@BritannicaRestorations21 күн бұрын
See next video!
@TriumphT100T22 күн бұрын
Wow Mike, hope you find the problem.
@AJB122 күн бұрын
Does it squeak at all turning the engine over by hand from the crankshaft? Other possibilities are a piston ring or valve guide too tight. And can you listen from underneath? If it's in the clutch/flywheel area, it might sound louder underneath?
@BritannicaRestorations21 күн бұрын
See next video!
@rberkel122 күн бұрын
Could be the clutch release bearing not fully disengaging (rubbing on the diaphragm fingers) or something else in the bellhousing (loose bolt) rubbing.
@BritannicaRestorations21 күн бұрын
See next video!
@thecolliman767422 күн бұрын
Hi just seen a very interesting video on FB where the pistons were catch on the crankshaft , I don’t know if this engines been rebuilt but it’s something to think about .
@fidicengineer-001d.mcelear822 күн бұрын
Tensioner for the timing belt, had same problem LR3
@BritannicaRestorations21 күн бұрын
Changed and still the same
@williambaird880719 күн бұрын
What about the timing belt tension bearing?
@BritannicaRestorations19 күн бұрын
New INA units
@rbrtcrowther22 күн бұрын
Head gasket blowing to atmosphere? Try slacking each injector mist probably number 4 and see if the squeak goes away or reduces 🤷
@BritannicaRestorations21 күн бұрын
See next video!
@williamwilcox-rd7cx22 күн бұрын
You said the noise happened when the engine is warm . Was the engine warm when you performed these tests ?
@BritannicaRestorations21 күн бұрын
Yes
@cx60hybrid9222 күн бұрын
When it’s back together. Try cracking off each injector in turn to see if it’s cylinder dominant
@BritannicaRestorations21 күн бұрын
See next video!
@MrRobmellor22 күн бұрын
I HAVE NOTHING BUT ADMERATION FOR YOU MIKE. I WOULD HAVE LONG SINCE GIVEN IT A EF OFF PILL. WISHING YOU THE LUCK THAT YOU RIGHTFULLY DISERVE. YOU ARE AN INSPERATION TO US ALL. MANY THANKS, YORKSHIRE ROB.
@BritannicaRestorations21 күн бұрын
Getting there Rob!
@mbengineeringltd489622 күн бұрын
You think it's a mechanical chirp? How about putting some smoke around the engine bay to check for high pressure gas leaks?
@BritannicaRestorations21 күн бұрын
Getting closer!
@evanjones253922 күн бұрын
I'm still thinking it's half engine speed, Injector creak (run engine and slacken unions one by one) or valve train, maybe a cam follower roller...
@BritannicaRestorations21 күн бұрын
See next video!
@billb344422 күн бұрын
This is way the best video you have made Mike. Better than a George Gently mystery. Never give up. They used to say if don’t succeed try and try again and if you still don’t succeed give up before you make a c*#@$ of yourself. The other one was if you can’t fix it bugger it up so no one can fix it. I never subscribed to either of those if only just to be bloody minded. You are the best mate. 🫡
@BritannicaRestorations21 күн бұрын
Thanks!
@overlandbyrover22 күн бұрын
maybe there may be some rubbing on one of the motor mounts, where the noise only occurs when the block is vibrating?
@donhappel956622 күн бұрын
Purely guessing since I'm not there in person, but it does make me think the noise was external to the engine.
@BritannicaRestorations21 күн бұрын
See next video!
@donhappel956621 күн бұрын
@@BritannicaRestorations done. And although you won't admit it, I think you are secretly enjoying the puzzle!
@BritannicaRestorations19 күн бұрын
Eating into hours and so far behind jobs
@edd611322 күн бұрын
Nothing worse than people guessing, but my 50p is something in the bell housing. Sounds like a dry squeek somewhere that's devoid of oil. Only place left to explore, poss a bolt backed out behind the flywheel?
@stephenfloat126022 күн бұрын
Is it one of the Injectors or even one of the pipes ?
@BritannicaRestorations21 күн бұрын
See next video!
@dariuszrad455919 күн бұрын
😄
@williamparry931421 күн бұрын
Just turn the radio up.
@gazzafloss22 күн бұрын
Mike, if it was an automatic tranny I'd say "flexplate". A mate had an auto Tdi D1, with that chirp it turned out the flexplate had cracked and the edges of the crack were rubbing together, evidenced by lots of fret corrosion in the bell housing. Could the flywheel centre be cracked?
@BritannicaRestorations21 күн бұрын
Don't think so
@Tinnunulus22 күн бұрын
We are all hoping you find it Mike it's there somewhere mate, have you tried leaving your wallet at home and see if the squeak goes 😜👍🇬🇧