Broken 8" Portal with L&W arm and fix talon X

[@dab1ou1n48]

Same thing happen to my rzr lastnight installing 8 inch portals brand new out the box

[@theirishaxe9405]

Get a lathe bro then you won't have to make videos being mad 👍 put a washer on the bolt then no play. You saw that tolerance before you tried to crank it down you could have just shimmed it out or sent it back. I would have been pissed and just sent it back. You can't machine out the ball end a bit and fit the stock one with the boot on this new shit? You can always tell how the company is by how they handle your probs no matter how small.

[@drumhard06]

I ran into the same issue. I just bought another set of spacers from them. I also noticed that they were different lengths in the bag. Between the two sets I was able to have the correct lengths with little to no play.

[@enaznhoj]

5:20 speaking the truth. Great advice and another great video. Thanks

[@WBOS72]

Absolute piss poor engineering on their part. Thanks for sharing, and saving us money.

[@BobKnar88]

Dude, I would have ran a smear campaign video on how much them products eat shit. Your a way nicer guy than me.

[@lilkeifer06]

Wish I would have seen this video before I just purchased there rear radius rods and forward a arms for my rzr. There fit for the rear was too wide. Had to grind down inside of knuckles to get them to fit. Then they sent me the wrong front arms. They did finally make everything right for me.

[@keeganfoster1792]

That is a actual horrible. Product you know its bad too when you cant even get it moving without it costing you money

[@prestonbarksdale6859]

What’s a good 28 that doesn’t float much that would be good for a foreman 520

[@monkeyman7048]

Low pressure Outlaws 3’s with beadlocks is always a good way to go. my buddy has them in his 500 foreman and they performed pretty well he didn’t really need a gear reduction either

[@ronniebowling1485]

I call BS on blaming and trash talking L&W. You should've checked for clearance issues as you where putting your rig together, and shimmed it accordingly before you even put it on the trail. L&W produces a quality product. I know cause I own a 2020 talon r with the same radius rods and high clearance lower a arms with 3000+ miles of royal blue ,tackett creek, and more trips than I can count to windrock. I also know other guys in my group that own polaris, can am and kawasaki that run these with zero problems. Maybe try to set your rig up properly before hand so you don't tear shit up. You are right they ain't cheap to work on.

[@MudPuppyOffroad]

You can call whatever you want no one cares the fact is their parts do not meet Factory spec but they're cheap so you can't complain too much LOL

[@bertrunner8386]

bruh don’t worry about the tolerances nobody buy this shit...... what if mudpuppy buys this shit.......crickets

[@nickruisoutdoors]

Could you use a washer instead of cranking it down

[@MudPuppyOffroad]

Whole video

[@A11ium]

How could they sell a product with such a crap fitment?

[@jessewoody5772]

Its all about Easy Money....Some manufacturers give zero fucks about you and their problematic junk products. Alot of aftermarket parts makers have no clue what geometric tolerancing is. I dont buy anything china if I can help it, most of it is junk headed for the landfill.

[@andrewvantassel5181]

Those joints will probably only last a couple rides since they aren't sealed and they are probably just low quality considering how everything fit and was built lol

[@andrewvantassel5181]

They are right tho, there is suposed to be play there. They just forgot to finish the sentence with "because we made our product wrong" 😂

[@MrMaster2017]

Next week they will probably try and ship him a remachined set free of charge and refund him on the cost of everything.

[@spencerbo1795]

Hey mudpuppy what is your opinion on brute forces with their reliability Also will you ever go to busco

[@MudPuppyOffroad]

My opinion on brute Force reliability is zero out of 10 probably the worst. Almost as bad as a Popo 850 or 1000

[@caseymaxwell7645]

Is it an oem knuckle? I was thinking of making my own arms with the Honda oem joints I’ve learn oem is good haha

[@MudPuppyOffroad]

No you much use the satv knuckle piece

[@johncox6292]

Try to stay away from spherical bearings total junk for the mud

[@Mattism78]

Did you see if it makes the noise when the machine is off the jack? I’m really curious if mine will make the same sound when jacked up because I get no movement when it’s on the ground. Quick comment about SuperATV. How are you going to make a windshield without stainless hardware? My latches are already rusting. Everything the sell just rusts. It’s super frustrating.

[@MudPuppyOffroad]

Depends how you're parked. Mine don't giggle much on the ground. Yeah satv fastener HW is junk

[@kcoble125]

aside from aztexs what other tire would you recommend, atv wise

[@MudPuppyOffroad]

I like OG outlaws

[@kcoble125]

@@MudPuppyOffroad so on a rancher 420 what would you recommend running, asking you because you give honest feedback. currently running 28 aztexs no gr however seem to dig in sand a little much for me, looking to go bigger. all i do is water riding, avoid huge mud holes unless it’s the only way

[@NiteHawk861]

Junk

[@richbon8825]

Where you riding this weekend

[@MudPuppyOffroad]

Maybe holopaw Saturday morning

[@dizzlerizzle2775]

that looks like alot of fun

[@tdawgoutdoors4393]

How did you get so good mechanically

[@MudPuppyOffroad]

A combination of tinkering and being a mechanical engineer I suppose

[@Ace-bk9yg]

1st