Thank you so much for video. I find new menthod by looking this. No need to remove any parts & fix all missing print head. Send 1 print from computer. As soon as it start unplug power cable. Take papper towen & do couple of fold. Soak with after shave or alchohol + few drops of water. Keep soaked papper on printer as in video. Rub printhead on papper. Leave print head few minutes. Repate process couple of times. I did 10 times with new papper tower. Fold three or four towel & repeat process as in video. I bring back my printer :) 100 % work.
@miguimau Жыл бұрын
Thank you , Sir. It's the second time I have to make this (forgot to keep it plugged and self-cleaning was not made). Hope you and the kitten are good.
@demagmusic6 жыл бұрын
Mr. Richard James is a wonderful accompaniment to your very helpful video
@christiansabanes89804 жыл бұрын
It sure helped me a lot! Excellent job. THANK YOU
@informediatech-bruno57665 жыл бұрын
the cat is part of the cleaning process? im asking because i only got a dog....do i need to buy a cat to clean my printer?
@marsdelapp77084 жыл бұрын
The magic fluid is WATER. Put the paper towel in under the print head as shown in the video. Pour a little water onto the paper towel. Move the print head over the wet spot and let sit for a little bit. Move the print head back and forth a few times and remove the paper towel. Repeat if you don't see all the colors on the paper towel. There is no need for "print head cleaning fluid", a syringe, tube. Just a little water on a paper towel worked for me.
@DonziGT2304 жыл бұрын
What kind of fluid is needed for cleaning the head?
@juntjoonunya92162 жыл бұрын
I just use rubbing alcohol. Half these guys use it, other half pay for the special "solution".
@krzysztofsmigrodzki70975 жыл бұрын
Jakiej średnicy (wewnętrznej) jest przewód, którego używasz do wpinania się w drukarkę (i gdzie ewentualnie szukać takich przewodów?) EN: What is internal diameter of the tube you use to plug into printer (and where should I look for such tubes).
@cleocat5623 жыл бұрын
What is with it with all these videos with music but no actual instructions?
@juntjoonunya92162 жыл бұрын
So I pushed cleaning solution through to Brother MFC-250C printhead, I've done it and each ink passage goes all the way through to the printhead as shown by soaked paper towel placed underneath, no clogs, then ran several test prints and printhead cleanings and only got maybe a faint print from the cyan, then nothing. Is the circuitry broken or something? The printer seems to think everything is fine. Must I push solution through again? I don't get the point as there is clearly no clog.
@mohammedmohammedsaeed95475 жыл бұрын
Tried this method with Brother MFC-480DW, i managed to inject the liquid into the Yellow color pipes, i could see the liquid came out at the klenex under the printer head, but still no Yellow color when testing the printer.
@boereboere4 жыл бұрын
mystery ... what liquids?
@Electronicview5 жыл бұрын
Great it is useful video friend. thank you for share and stay connected
@Polyester_Avalanche5 жыл бұрын
Very helpful! What diameter tubing did you use?
@sgtbilkothe3rd5 жыл бұрын
@Axel Steiner it's later now.
@joshmundy37302 жыл бұрын
@@sgtbilkothe3rd Very later now
@sgtbilkothe3rd2 жыл бұрын
@@joshmundy3730 yup.
@philippecharteronzaoui11034 жыл бұрын
Merci pour la vidéo, j'ai exactement le mème modèle depuis plus de dix maintenant, juste une question, c'est de l'acool a bruler ou du diluant le produit a injecter dans les buses de couleurs ? Donner réponse SVP merci d'avance
@hongkongmartauction3 жыл бұрын
it is helpful! Thanks a lot!
@trumpetflowerII3 жыл бұрын
Not able to follow you; get a script and use it to enable all to understand what you are doing.
@valentinoruggiero73097 жыл бұрын
Salve volevo chiederti ma che liquido usi per pulire
@bassgoul3 жыл бұрын
tried this method, made the printer even worse afterward... was having trouble with magenta and lost cyan as well after this. i think my printhead is screwed. also made a gigantic mess, as ink/solution came out of the other empty ports while squirting this stuff in. it's worth trying for a last ditch effort though, i guess
@orlandobueno84336 жыл бұрын
hello good afternoon greetings from venezuela I have a brother mfc-240c printer which the yellow does not want to subduct yellow ink and I uncork it and with a syringe I put on it yellow stamp and if it prints but until it dries the ink that is left cavezal and then the same problem does not print me that it will be
@birrento3 жыл бұрын
Hello, what is the solution that you inject in the ink sistem? I have cleaning solution from inktec (MCS-100MDP)
@ainimohd.zainolazlin45014 жыл бұрын
thanks..really helpful..done doing mine..
@pulungadiyatma1277 жыл бұрын
save for print head?
@juancarloshortasanchez1992 жыл бұрын
After make this proccess the printer show me an 48 error and the head doesn't move, what can I do??
@missmesmerize2575Ай бұрын
Have the same problem! Actually, the error is called printer 4F error. Cause: wrong ink or problem with the printer head. Maybe there is too much air in the system, so I would try to get it out (repeat the procedure!). The more likely reason: the printer head needs replacement.
@stevenreiss6 жыл бұрын
was genau wird eingespritzt wenn nicht isopropranol ?
@missmesmerize2575Ай бұрын
Eine Mischung aus 20 ml Isopropanol und 80 ml Glasreiniger soll eine geeignete Reinigungsflüssigkeit ergeben. Oder aber man verwendet eine im Handel erhältliche Reinigungsflüssigkeit.
@alessandroarnoldi48274 жыл бұрын
Che liquido hai usato per spurgare ? Diluente nitro?
@hussinaliali69646 жыл бұрын
What is in green bottle
@marsdelapp77084 жыл бұрын
I think it could be either Acetone, Xylene, Toluene, Kerosene, Methyl alcohol, Ethyl Alcohol, Gasoline, or water. I am guessing that it is not Isopropyl alcohol because the description says, "Isopropanol is used only for cleaning of excess ink. DO NOT use this to clean the printer head!" Now I just need to find a video that actually shows how to clean my print heads instead of a video that leaves you guessing.
@amanciang4 жыл бұрын
Printhead Hospital Cleaner
@dandan-cp6tk7 жыл бұрын
Jeśli dobrze zrozumiałem, najpierw wstrzyknąłeś rozgrzany płyn do płukania (czyszczenia) głowicy. Następnie do wyczyszczenia resztek użyłeś alkoholu izopropylowego (butelka z oznaczeniem SHL (UK))? Jakiego płynu użyłeś do czyszczenia głowicy? Czy nie lepiej byłoby najpierw odciągnąć strzykawką pozostałość atramentu z przewodów i głowicy i dopiero po tym zabiegu wstrzyknąć rozgrzany płyn? Gdzie można nabyć strzykawkę z takim adapterem na przewód drukarki który wchodzi do kardridza? Ewentualnie pamiętasz średnicę wewnętrzną tego wężyka co użyłeś? Pozdrawiam
@Matitiasz7 жыл бұрын
Zgadza się. Izopropanolu, użyłem tylko do czyszczenia "sprzętu", (strzykawki, rurki, obudowy drukarki ). A jaki środek do czyszczenia ? Ja użyłem gotowego, który możesz zakupić na ebay. ale można samemu zrobić taki płyn, wedle przepisów z netu :) skład to np. około 30% izopropanol + 70% płynu do czyszczenia szyb. (płyn bez dodatków, jak np. extra zapach) - poszukaj przepisów, bo są różne. Nie ma potrzeby niczego odciągać , ale jeśli chcesz to możesz eksperymentować. Możesz kupić gotowy zestaw już z rurką i strzykawką, lub samemu zrobić płyn , a strzykawkę i rurkę (jak od kroplówki) na pewno gdzieś dostaniesz. Życzę udanego czyszczenia :)
@wojteksmag82866 жыл бұрын
A czy można zwykły etanol (alkohol etylowy, denaturat), zamiast izopropanolu?
@MarekKrassus537 жыл бұрын
Dobre.
@carlchristensen5844 жыл бұрын
Yeah, like others here, a tubing diameter would be helpful.
@carlchristensen5844 жыл бұрын
FYI. Long ago I purchased an ear wax cleaning kit. It had a large bulb 'dropper' made of green rubber. Since it was opaque, I cut off the small tube portion of the dropper, fit it snugly over the end of my syringe, and then cut down the other end to a size that would slip over the ink nozzle. Unfortunately, no clear tube between the syringe and the nozzle, but was able to gently persuade the solution through the system.
@duke85live5 жыл бұрын
1 like just for the cat ;D
@jimviau3276 жыл бұрын
Hey Matitiasz, Thanks for this video but you could have given us a little more details such as If you forbid using IsoPropanol what then should be used? Furthermore, why are you using two different liquids? what are they? Please reply with those important details. Thanks (PS: I cant read PL ??? )
@Matitiasz6 жыл бұрын
I intentionally didn't give the name of the cleaning fluid, I don't get paid to advertise, and the choice of cleaning fluid is quite large. One can even make their own. For example, a formula could be 30% isopropanol and 70% window cleaner (without any additives). Look for formulas/recipes yourself as there are many. In the film I only used pure isopropanol to clean the exterior of the printer and the syringes themselves.
@irismunoz18072 жыл бұрын
@@Matitiasz p
@leonardozago97066 жыл бұрын
You can also do deep cleeaning function as well. Turn off the printer, then press Menu and contemporary switch on the printer, the press 7 and then 6 and then 4. So you can start the laboratory cleaning procedure! Bye !!
@ronk10306 жыл бұрын
What is the contemporary switch?
@DougieDiety5 жыл бұрын
Edit! Two minutes of useful info in a nine minute video.
@Matitiasz5 жыл бұрын
:)
@MrGraphicplayground4 жыл бұрын
Great choice of Music... I thought it was coming out of Spotify... ahhahahaha
@jasonsosnick8669 Жыл бұрын
I bought this printer kzbin.infoUgkxciSwynMJ7PnUvvx11rewiu-yFBkZTl53 to replace an aging HP printer. It is just used for casual home printing so I don't need anything more. Installation went easily though the HP Smart Printing doesn't work well with our laptops - having to select the actual device. Will have to see how the HP Instant Ink program works out. Plus haven't been able to set up printing from smartphone yet - either direct or WiFi