Cutting straight lines with a jigsaw using the router method

[@avrahamgoldberg9731]

Wouldn't it be easier to just clamp a straight edge to the workpiece and use that as a guide? The method in the video essentially does the same thing, but with the added step of screwing a piece of wood to the jigsaw.

[@BStarCrafts]

Thank you for good comments 😊 Have a nice time 🍀

[@marcoguo9633]

I think theres a good chance that the jigsaw could wear out the edge or cut straight through in that case. I can see why this method is better long-term since it doesnt wear out the straight edge after repeated uses.

[@marcopinchetti5872]

your idea has one benefit: you can cut thicker pieces. THOUGH: it's not so immediate to place the "guide rail" at the perfect distance. It's easy, but not as immediate as this method reaches

[@newmonengineering]

@@marcopinchetti5872 the way I do it is by using guide blocks. Basically a pair of blocks that define the distance from the guide to the line. It's fast to set up and you can always use a metal guide like a t track if you are concerned about wear. But if you are doing a lot of them it can become time consuming in comparison to this method

[@powerpc6037]

Not to mention the added distance between the machine and the workpiece, allowing the blade to bend a little when it follows the grain of the wood. with the machine on the workpiece itself, the blade cannot bend that far, allowing for more precise cuts.Also, wood against wood gives more friction instead of metal against wood.

[@arun.sekher]

🙃🥴The irony of this video is that you need advanced power tools, like a table saw, to create a jig for making straight cuts with a jigsaw. However, if beginners had access to those advanced tools, they would likely choose to use them instead of a jigsaw for this specific task.

[@liam314]

You could use the factory edge of a sheet of plywood to make this. That way you would not have to make any accurate cuts to make this jig. But you make a fair point. This is always the problem with these types of yt videos, "excuse me while I whip out my perfectly set up table saw to make a jig for cutting straight lines!" ;) Anyway, I will try to make this using only a jigsaw and a cordless drill

[@Zjaan321]

Better to use the right tool for the right job. But if you have nothing else, I guess this can work as a permanent workaround if you not planning use the jigsaw for something else. Can also just use a guide and clamp as usual instead of fixing wood to the jigsaw which you will need to remove again when using it as intended. The ideal tool will be a circular saw and will give a much more desirable finish. Jigsaw is better for odd shapes, curves and tight corners in my opinion.

[@BStarCrafts]

Thank you 😊 🍀👌Have a nice time 🍀

[@chowderwhillis9448]

Exactly no offense uploaded but this is kinda stupid and just to get KZbin views, not practical on the jobsite

[@b3arwithm3]

Exactly, the blade always flex thus no point trying to make accurate cuts. The only benefit of this jig is we don't have to account for the width of the base when placing the straight egde

[@nameless5r]

@@chowderwhillis9448 not really but you're entitled to your stupid opinion... So.....

[@SimplySketchyGT]

Indeed a track saw will work better. But if you need to use a jigsaw this is a genius method.

[@Николай-х5э2ч]

Сверху пил ровный, а вот за счёт мягкости пилки и фиксации её только с одной стороны 90° торец всё равно не получится. Только Фрезер, ленточная пила или циркулярная даст ровный пил и торец 90°... Бессмысленная приблуда, с тем же успехом можно подошву лобзика просто упирать в направляющую

[@BStarCrafts]

Спасибо 😊 Хорошего дня 🍀 감사합니다 😊😊 좋은 하루 되세요 🍀

[@АлександрКруглов-к7й]

Б. Инженеры придумали инструмент, для криволинейных распилов. Нет. Б. Народ, упорно продолжает пытаться запустить его прямо.

[@yuryGens]

@@АлександрКруглов-к7й , мы не ищем легких путей, такова природа русской души )))

[@АлександрКруглов-к7й]

@@yuryGens Упрощать сложно, усложнять легко.

[@LearnObserveReact]

The black plastic guard that is on the bottom of the jigsaw...actually has square and parallel sides. Put a straight edge on the top of your timber and use it instead. Good brands state on them how wide they are between the edge and jigsaw edge.

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@한희혁-m2e]

역시 응용면에서는 따라갈 사라이 없을듯 유익한 영상 잘보고갑니다 다음 영상도 기대해볼께요 ~~~

[@BStarCrafts]

감사합니다~ 이번주 사업 대박 대박 기원합니다 🍀🎁👍

[@budkim4074]

형님의 아이디어는 늘 새롭습니다~^^ 너무 멋진 방법이네요~*^^*

[@BStarCrafts]

고마워 선화야~ 이번주도 해피 해피 🍀💚 날 풀려서 굿데이네 😁😊🤜🤛

[@oldschooldiy3240]

You will never have the same quality of edge as with a flush trim bit! The jigsaw blade has too much deflection(flex) in it....better to use a table saw or circular saw!

[@stigmautomata]

i like this design as it allows the clamped guide to be placed directly on the intended cut,

[@sampathkumar3018]

Yes. I too found it difficult inspite of all adjustments.

[@Musicpins]

Because most jigsaws is junk, a circ saw is better yes.

[@GustavoArayaPaillas]

😊😊😊😊😊😊😊

[@UrdnotAkongo]

You missed the entire point of why something like this might be helpful, maybe they don't have other tools? You ever think of that? "Just use X tool" is such a weak argument. Yeah that's true, if you don't have constraints on budget, storage space, etc.

[@인테리어용접기능장]

안녕하세요 구독 좋아요 꾹꾹 누르고 시청하고 있습니다 저도 만드는걸 좋아해서 여러가지 국가 기능자격증도 취득하고 더 좋은 제품을 만들고 싶어서 도전 중입니다 선생님께서 알려주신 방법은 제게 가구 제작 기능사 실기 시험을 보는데 많은 도움을 줄걸로 사로 됩니다 아울러 선생님 채널도 번창하세요

[@BStarCrafts]

감사합니다~ 하시는 일 대박 나시고 시험도 한번에 붙으시길 바라겠습니다 🍀🍀💚🎵👍

[@DianaLuckysova]

wow. genius! I don't want to use circular saws and this is the best solution I've seen to improve jigsaw cuts. Thank you so much for sharing!

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@namhyungkim1267]

영상보고 만들었는데 하드우드로 만들어야 겠더군요. 소프트 우드로 하니 자꾸 움직여서...😅😅😅 좋은 팁 감사합니다.

[@BStarCrafts]

아… 뭐든 지그나 도구는 하드우드로 만드는 것이 좋은 것 같아요~~ 안전 목공하세요. 🍀🛠️😊

[@kenmoulton5221]

If you have a square or a straight endge you can run it against the the saw guide and will save you time and gives precision.

[@theredrooster7143]

Yeah, there’s no point in doing what he did if you’re running the saw against a straight edge anyway. Just back up the straight edge and run the guide along it like you said.

[@papabeoms]

와우 감사합니다. 자처럼대고자르는 나무두께와 직소바닦에있는 나무두께가 동일해야겠네요. 안그러면 약간사선으로잘릴듯하네요. 그런궁금증이생기네요^^ 아닌가? ㅋㅋ 잘몰라서요... 정말고민많이했는데, 이렇게 알려주시니 감사드립니다.^^

[@BStarCrafts]

네 아주 정확하게 보셨어요. 사실 영상을 찍을 땐 귀찮아서 12T를 대고 잘랐는데 안정적으로 자르기 위해선 지그 두께와 같은 18T를 대고 자르면 아주 좋습니다. 그래서 그 다음 영상인 원형톱은 18T로… 😅 좋은 하루되세요.👍💚🍀🎁🤜🤛

[@papabeoms]

@@BStarCrafts 정말 좋은 아이디어 제공해주셔서 감사드립니다.^^ 영상 자주보고 있어요~ 즐겁게 취미생활할수 있게 도움많이 주셔서 감사해요~

[@TheMadJester159]

Probably wouldn’t be using a jigsaw if I needed straight cuts but making jigs are enjoyable. Good job on that.

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@강화무]

가이드를 멋지게 만드셨네요. 좋은 아이디어입니다 톱작업 대신으로 작업해도 될것같네요. 지금 리모델링하는 작업대가 완성되면 제작해보겠습니다..감사합니다~~✅

[@BStarCrafts]

감사합니다~ 추운데 안전 작업하세요~^^

[@Doliday]

와... 이건 저도 써먹어야겠어요 🌟🌟 매번 잘 보고 가요 😶‍🌫️😶‍🌫️

[@BStarCrafts]

감사합니다. 저보다 훨씬 정교하게 잘 만드세요~ 🤜🤛👍💚😊

[@miryu_kim]

안녕하세요 영상 맨처음에 나오는 구불구불한 형태처럼, 드로잉같은 자유분방한 형태로 자르는 작업을 하고자 합니다. 영상에 나오는 형태도 직쏘로 자르신 것인가요? 또 자르신 나무는 어떤 집성목인지 여쭤봐도 될까요?

[@BStarCrafts]

네 같은 직소기로 자른 거 맞습니다. 원래 직소기는 구불구불 자르는데 특화되어 있습니다. 영상 사용한 목재는 고무 나무입니다. 주말 잘 보내세요 🍀

[@miryu_kim]

@@BStarCrafts 와 답변해주셔서 정말 감사합니다!!

[@UpSigurd]

С направляющей планкой можно было добиться такого же результата с самого начала.

[@ilhojeong3131]

페스툴 직쏘기가 따로 필요 없겠네요~~~~ㅋ 정보 감사합니다~~ㅎ 추석명절 잘 보내세요~~^^

[@BStarCrafts]

페스툴님과 비교해주시다니… ㅎㅎ 명절 잘 보내시고 좋은 밤 되세요 👋💚🍀

[@kisado7142]

간단하면서 실용적이네요👏😁😊 역시 아이디어뱅크!👍 요새 매일 공방에 계시나요 언제 연락 드리고 갈께요~

[@BStarCrafts]

감사 감사합니다 😁😁😁 네 오셔서 차 한잔 하고 가세요. 요즘은 자주 나가진 않습니다만 닐 풀리면 자주 나갈라고요. 👌😊

[@DanDDirges]

Very good idea but I always have blade deflection when I use a jigsaw. Never cuts square for me and I`ve tried many high quality blades. I think you would have the same problem with this technique cutting curvy lines thru thicker stock.

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@mokumoku_]

무척 유용할듯 합니다. 가끔씩 끝까지 다 안자르고 중간까지만 자르는 컷이 종종 필요한데, 테이블쏘나 원형톱은 일자로 깨끗하게 잘리지만, 중간까지만 자르는거는 원형자국을 남겨서 문제죠. 이럴때 직쏘가 가장 적절한데 직선을 자르는게 힘들었네요. 좋은팁 감사합니다

[@BStarCrafts]

업로드 후 그 부분 설명이 부족해서 아쉬웠는데 브연 설명을 정확히 해주셨네요. 감사합니다.👍🤜🤛👌 커다란 별모양을 자르는 장면을 시연했음 좋았을… 😊😊😊😊😊

[@루하핑]

와 기발하다.. 좋은정보 감사합니다. 내일 당장 만들어봐야겠어요!

[@BStarCrafts]

감사합니다. 이번에 새로이 업로드한 원형톱 응용 영상을 보시면 조금 더 참고가 되시듯 합니다 💚👍😊🎁🍀

[@pacidonodono7546]

Terimakasih banyak atas idenya.. Two tump up... Bogor Indonesia hadir

[@BStarCrafts]

Terima kasih 💚🇮🇩😊 Semoga harimu menyenangkan 👍🍀👌

[@davidflavin]

Great solution to finish 👏👍 Even with a circular saw you could get a wobble.

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@DrLumpyDMus]

Circular saws wobble but the saw kerf is consistent. When used with a fence, wobble will produce a kerf wider than the blade, but it won't produce a wandering cut like a saber saw. The angle of the blade to the work does not vary in a circular saw. It varies quite a bit, and unpredictably, in a saber saw.

[@viorsa8200]

Excelente proyecto muy bien desarrollado y mejor ejecutado , con esa plantilla fácil de hacer y de colocar , problema resuelto y buenos cortés , gracias por compartir tanta creatividad y conocimientos , un saludo cordial y por supuesto un gran like desde Narón , Galicia (España) 🤓 🛠️ 🔝

[@BStarCrafts]

🙆🙆🙆 Gracias Viorsa 🍀🎁👍🤜🤛😊 Que tengas un buen día 👍🍀👌

[@JohnSnow-vf8jo]

Amazing, I never realised you could get screw driver bits with handles on. LOL.

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@petermcmurray2807]

Thank You. I need to make angled cuts on a 1900mm piece of plywood. This will do the job much more accurately than trying to follow a line. In fact I can use it with a circular saw. Much better than the saw guide cutting through the centre that I tried. Straight edge is of course another piece of ply.👍👍👍

[@BStarCrafts]

Thank you 🤜🤛😊 Have a nice time 🍀

[@wayneduval7847]

Excellent! Really great way to keep the cut straight. 😎

[@BStarCrafts]

Thank you 😊👍💚😊 Have a nice time 🍀

[@clintcowles7563]

A clever idea for specific purposes. Neat! Happy building and staying busy. Northern Michigan here by the way. 😁

[@BStarCrafts]

Thank you 💚👋😊 Have a nice time 🍀

[@jaaman0670]

Bravo, belle réalisation, c'est simple, mais il fallait y penser 👍😃. Comme quoi, avec un peu de réflexion, tout est réalisable !

[@BStarCrafts]

Merci. 🤜🤛👍💚 passe une bonne journée 😄🍀

[@John01GM40]

can't see how this is better than running the jigsaw down the guide rail you attached with the clamps and not messing around with a bit of wood screwed to the jigsaw

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@ETILHK54]

Neat idea! Thought about the same thing a few days ago, as whenever i cut, i have to work out the inconsistencies later, getting tired of it, wasting time.

[@youbabo]

최고 ^^ 안그래도 직쏘기 가이드 만들려고 했는데 마침 이런 동영상이 있었네요. 참고하겠습니다.

[@BStarCrafts]

감사합니다. 혹시 탭핑 비트 있으시면 오늘 올린 원형톱 응용 영상을 참고하시면 일직선(영점) 잡기가 훨씬 수월할 겁니다. 좋은 저녁되시고 안전 작업하세요. 🍀🤜🤛😊

[@hermannclasen8196]

@@BStarCrafts dä

[@sajasaja4930]

T twe

[@cesarlukyanski5352]

El sabe sabe, abrazo desde argentina. Gracias por compartir su sabiduría.

[@BStarCrafts]

Gracias 😊 Que tengas un buen día 👍🍀👌

[@vanzipper6486]

The best cut and under the panel👍In Switzerland we put the machine under the panel

[@BStarCrafts]

Thank you 👍💚🇨🇭😊 Have a nice time 🍀

[@CBDuRietz]

Crap! It seems that I need to buy a table saw in order to make a jury rigging of my jigsaw in order to not having to buy a table say... 🤣

[@윤현진-c5s]

똑같은 장비도 누가 어떻게 쓰느냐에 따라 틀리내요 ~~ 오늘도 감탄하면 감상했습니다 ^^

[@BStarCrafts]

💚🎁👍😁😁😁😁 새론주 멋지게 고고 😊

[@antoniosolorzano9175]

@@BStarCrafts mensaje y i

[@antoniosolorzano9175]

L

[@luinroberto4887]

By

[@cris2rire]

Lille

[@DiHandley]

Excellent idea, I think I’ll use it. What part of the world are you from?

[@BStarCrafts]

Thank you 👍😊 Have a nice time 🍀 I live in Korea 🇰🇷🇰🇷🇰🇷💚

[@planeta1961]

Muchas gracias. Muy útil. Desde Ica- Perú.

[@BStarCrafts]

Gracias 😊 Que tengas un buen día 👍🍀👌

[@reviewtoday1965]

Hey Maker. Great tips. Thanks for sharing.🍁🍁👍👍

[@BStarCrafts]

Thank you 💚😊 Have a nice time 🍀

[@princeamongmen7064]

Great idea mate will deffo use it especially if I can find my plastic footplate, I can set it up and use it at will!

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@bradleytuckwell4854]

Simple jig but very Accurate and precise thanks for sharing

[@BStarCrafts]

Thank you 🤜🤛👍😊 Have a nice time 🍀

[@СергейКузнецов-ы7я9с]

Изобретение на пустом месте, что если направляющую крепить немного дальше (на половину подошвы лобзика) и тогда к подошве уже не нужно ничего прикручивать

[@BStarCrafts]

🤜🤛

[@mallencolly]

I love the bit where you need a table saw to get the straight cut on the guide you need for a tool thats not the best option, still have to clamp straight edge to your work, and will still probably get a wonky edge because it's a jig saw. 😂 Either cut with a jig saw and use the router to get the edge you want, or cut with the damn table saw

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@bramweinreder2346]

If you use templates this works with almost every shape, including guitars. This is actually a very common and straightforward method. But if you want something straight, a chisel or a plane would also do a fine job, just takes more skill and time.

[@oz6082]

this is innovative thanks for posting. however my issue with jig saws is not only a straight cut but always blade deflection causing the blade to angle and vertically out of plumb. does this jig prevent this? if so, why?

[@tuckersossaman236]

Most jigsaws will have an adjuster for blad tension to make the blade cut more stable making the edge plum vertically, if using an older or cheap model the tension may slip causing the edge to not be vertically straight but you're definitely right with this being a problem. Much better off setting up a jig with a drill and a table saw blade for a cheap alternative to a table saw for making straight cuts. There's a few vids out there on how to do it. If wanting to use this method cutting very slowly to reduce pressure on the blade will help 🙂

[@oz6082]

@@tuckersossaman236 Thanks for the suggestions!

[@gabydewilde]

Don't push it, go as slow as possible.

[@DiegoSynth]

@@tuckersossaman236 My issue with jigsaw is that I can follow a straight line while cutting, so I get it straight on the top but totally messed up on the bottom if the wood is thicker than 1cm. Does what you explain help with this problem? Thanks in advance!

[@yamadog24]

Just clamp a straight edge to your workand use it as a guide. Works great for jig saws and circular saws.

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@saputracandra4203]

Mantap Pak Eko.... Terimakasih 🙏🙏🙏

[@BStarCrafts]

terima kasih. 😍💚👍 Semoga hari anda indah. 🍀😄🇲🇾

[@nikolsputinbaev8485]

На мой взгляд проще было бы закрепить провило с двух концов при помощи струбцин и по ней упором делать распил, используя электролобзик. Для распила ЛДСП использовать пилку по металлу (с частыми мелкими зубьями). Получается не хуже, чем на распиловочном станке

[@BStarCrafts]

Спасибо 😊 Хорошего дня 🍀

[@bugalol]

Искал этот коммент)) 👍

[@MiniPsalt]

Всегда так пилил лобзиком , когда был нужен идеальный рез . А тут - изобретение велосипеда .

[@vladimir51ful]

@@MiniPsalt идеальный рез лобзиком????????

[@MiniPsalt]

@@vladimir51ful Сам был удивлён! Когда купил лет 10 назад Фиолент красной серии . Причем пилил белое ДСП .

[@marcenariahobby7pallet]

Ficou muito top seu vídeo parabéns já deixei o meu like 🇧🇷👍👍👍👍👍💯

[@BStarCrafts]

Obrigado 😊💚💚🤜🤛😊 Tenha um bom dia 🍀

[@garoudahanouman7734]

Well, this is not the router but the trimmer method! Anyway, it's a good idea!🤗

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@rowancant3071]

I tried to do something like this the other day, but I found that my jigsaw blade bent over sideways and went whereever it wanted anyway. Even if you get it straight horizontally, it’s not very square in the vertical direction.

[@BStarCrafts]

Thank you for advice 😊 Have a nice time 🍀

[@sddiymakeitworthit7512]

Nice job really useful 👍 🙏

[@BStarCrafts]

Thank you 😊 💚🤜🤛 Have a nice day 🍀

[@사색나무]

영상 초반에 삐뚤게 자르고 뭔가 둥근 거 달린 기계로 깔끔하게 미셨는데...그 기계는 이름을 뭐라고 하나요??

[@BStarCrafts]

기계는 라우터이고 사용한 비트는 스트레이트 베어링 비트라고 합니다 ^^

[@BeaulieuTodd]

As creative s this is, to me, it just proves the point that jig saws are not precise tools. That was a job for a track saw.

[@BStarCrafts]

Thank you 🍀💚😊 Have a nice time 🍀

[@maggyliciousss]

Super! Ich liebe solche simple und hilfreiche ideen 👌🏽

[@BStarCrafts]

Danke 🤜🤛💚🥹😊 Schönen Tag 🍀

Bravo ! Cette astuce est géniale !

[@BStarCrafts]

Merci. 🤜🤛🎵👍💚passe une bonne journée 😄🍀

[@serferinterneta]

Классно. Спасибо за способ.Надо попробовать модернизировать лобзик.

[@BStarCrafts]

Спасибо 😊 Хорошего дня 🍀

[@metalcraft9642]

И ты туда же? Реально думаешь что лобзик отрежет идеально ровно?

[@plutoblue8181]

굿 아이디어 입니다

[@BStarCrafts]

감사합니다 😊👍💚😊 좋은 하루 되세요 🍀

[@vnrkain1169]

Thank you. This video is precisely what I needed.

[@BStarCrafts]

Thank you 💚👍🤜🤛🎵😊 Have a nice time 🍀

[@tylerdurden9879]

I like that. Greetings from Germany. Amithaba.

[@BStarCrafts]

Danke 😊 🇩🇪 Schönen Tag 🍀 Thank you 😊 Have a nice time 🍀

[@ПавелАгеев-и2ш]

👍👍👍 А просто, без деревяшки на лобзике, нельзя???

[@BStarCrafts]

Спасибо 😊 Хорошего дня 🍀

[@veganpotterthevegan]

Using a jigsaw which tons of people have... and a router which most people don't even know exists😅

[@AleksandrFedot]

С угольником Свенсона в виде упора все получается так же,но гораздо проще и быстрее.

[@BStarCrafts]

Спасибо 😊 Хорошего дня 🍀

[@НиколайВольный-в9л]

Также сделаю. Спасибо автору за идею.

[@BStarCrafts]

Спасибо 😊 Хорошего дня 🍀

[@easternbrown]

Good solution to a jigsaw puzzle 👏

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@Beo_drago]

Was with you up til the end. Seems like a lot of work just to raise the jig saw higher away from the material. Point is you could just cut out the middle jig (play on words, lol) and just run the jigsaw's base against a straight edge instead of fabricating and attaching a higher base that's going to run against a straight edge. It just seems like wasted effort, much like my comment, lmao.

[@jeffpittel6926]

Interesting, I wonder if you left the hole round, and fitted a Delrin plug with a slot the same width as the blade would make it cut even truer.

[@BStarCrafts]

Thank you 😊

[@godofwars99]

Thank you/from Thailand.

[@BStarCrafts]

ขอบคุณค่ะ 😊💚🎁 ขอให้เป็นวันที่ดีนะคะ 🍀🇹🇭

[@AlbertH99]

Ingenious but quicker to set up and use a portable rip saw.

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@joeshuge]

Quicker to just keep the saw tight against the straight edge he clamped and not bothered with all the rest.

[@AlbertH99]

@@joeshuge my jigsaw tends to wander away from where it’s supposed to cut

[@joeshuge]

@@AlbertH99 slow down and keep it tight .

[@AlbertH99]

@@joeshuge will give it a go!

[@897589751]

Если просто по направляющей доске пилить, то также получится)))

[@BStarCrafts]

Спасибо 😊 Хорошего дня 🍀

[@LeonardoSilva-xs2du]

Very good my friend 👏🏽

[@BStarCrafts]

Thank you my friend 💚🎵😊 Have a nice time 🍀

[@starjared12345]

That is a really good idea. Cheers

[@BStarCrafts]

Thank you 🤜🤛🙏💚😊 Have a nice time 🍀

[@viryawanvajra2217]

Nice idea... Never thought before... Thanks

[@BStarCrafts]

Thank you 🎵💚🤜🤛😊 Have a nice time 🍀

[@ГансСосискин-ч3г]

тип изобрел параллельный упор! круто.

[@Stan_the_Belgian]

So all I need is a table saw to make a tool to do what a table saw can do.

[@TV-ol9pc]

와우 신기해요 영상 잘봤습니다 🙂

[@СергейНиколаевич-х5ж]

Поддерживаю

[@BStarCrafts]

감사합니다 멋진 한주 되세요 🎁😊😊 좋은 하루 되세요 🍀

[@rock_machine01]

It still wandered! That’s the nature of the jig saw beast! Nice try however.

[@BStarCrafts]

Thank you 😊 👍Have a nice time 🍀

[@MakeshiftFrank]

This is a great idea. Thanks for the video.

[@BStarCrafts]

Thank you 🤜🤛💚😊 Have a nice time 🍀

[@joeshuge]

It's a complete waste of time, did you see he clamped the straight piece of wood to the wood he was cutting? All he had to do was move it over to allow the blade to cut on the line he wanted to cut and just keep the base of the jigsaw tight to the clamped wood, he would have had the exact same outcome without going through all the wasted time attaching a piece of wood to his jigsaw.

[@bitminersouth8845]

Very useful trick, thanks What is the tool used at 0:52 please ?

[@BStarCrafts]

Strait router bearing bit… 😊👋 Thank you 😊 Have a nice time 🍀

[@РадикНасыров-з8р]

Всё гениальное - просто! 🤝👍

[@BStarCrafts]

Спасибо 😊 Хорошего дня 🍀

[@riccardovagli0000]

Good job! Where can i find the plug-in support for the plate?

[@BStarCrafts]

I'm not sure about that. 😥 Thank you 😊 Have a nice time 🍀

[@riccardovagli0000]

@@BStarCrafts Thank you you ;-) I mean... I don't know how to say in english the plastic protection of the plate, the slide... That black stuff underneath the plate of the jigsaw: where can I find it? I think there are many valid ideas for making straight cuts with the jigsaw, and yours is very good. But I always have the same problem: the blade bends.

[@ВладимирКалинин-г8л]

Эврика!! Чтобы две доски идеально сошлись, их нужно пилить вместе!!! Это я знал, этому меня научил отец, как только я начал пилить!

[@BStarCrafts]

Спасибо 👍🤜🤛🍀💚😊 Хорошего дня 🍀

[@layrtonsilvasoares4016]

👏👏👏like e Seguindo!!!

[@BStarCrafts]

Obrigado 😊💚😊 Tenha um bom dia 🍀

[@agordencat1585]

Ill I can say is…AMAZING!!! Im gonna make one!

[@BStarCrafts]

Thank you 💚🎁👍😊 Have a nice time 🍀

[@tamito9298]

Все гениальное просто Супер

[@BStarCrafts]

Спасибо 😊 Хорошего дня 🍀

[@knightclan4]

Thanks for sharing your knowledge

[@BStarCrafts]

Thank you 💚🎁😊 Have a nice time 🍀

[@coloradomountainman8659]

Good video. Nice not to have it ruined by irritating, obnoxious, annoying and distracting background "music" like 97% of other KZbin posters (except for one little blurb starting at 1:27 but I can overlook that.

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀 But… 1:27… No ad… All advertisements must be marked as paid advertisements. 😊😅

[@daniel_martin]

I bet the table saw used for this project does great rip cuts too

[@BStarCrafts]

👋👋💚

[@tvyoutube3464]

검은별공작소님! 취미로 유튜브 하시는건가용?

[@BStarCrafts]

취미겸 겸사겸사로 합니다. 좋은 하루되세요 💚👍🍀😊

[@sbaa3238]

Bien . Astuce facile et simple 👍

[@BStarCrafts]

Merci.💚 passe une bonne journée 😄🍀

[@silverlee9018]

봐도 잘 이해가 안가는데 저거만드려면 테이블 쏘가 있어야 하나요?

[@BStarCrafts]

아니요… 평이 잡힌 두께 18mm 막대 그리고 직소날이 들어갈 구멍 (원 또는 삼각 사각 상관없어요)을 뚫은 후 직소기 아랫판과 연결하면 됩니다. 😊

[@astroman269]

Riiight... Because someone who is looking to cut a straight line with a jigsaw with such a hack has all the OTHER necessary tools to make this holder for their saw. Cool trick though!

[@BStarCrafts]

👍👌Thank you 😊 Have a nice time 🍀

[@liondrones2757]

Ficou top das galáxias. 👍

[@BStarCrafts]

Obrigado 😊💚💚💚💚😊 Tenha um bom dia 🍀

[@pathardage1880]

This is brilliant. Thank you.

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀

[@nickpont8567]

Very clever, thanks for the upload.

[@BStarCrafts]

Thank you 🎵👍💚😊 Have a nice time 🍀

[@紅髮小菁YT網]

很細緻的手工

[@BStarCrafts]

谢谢😊 👍💚 祝你有美好的一天🍀

[@紅髮小菁YT網]

@@BStarCrafts 謝謝

[@angakies5253]

Nice ideas broo..👍👍👍

[@BStarCrafts]

Thank you bro…! 👍💚😊 Have a nice day 🍀

[@RobertKarlBerta]

Instead of wood I use lean or plexiglass. I cut a zero clearance slot with blade I will use in saw. Due to zero clearance it cuts a clean cut without splintering and you can watch the cut through the plexiglass. I attach the plexi to the saw soul plate with carpet tape (amazing how useful carpet tape is for woodworking) so easily removed so reverts to normal use.

[@BStarCrafts]

Thank you 😊 Have a nice time 🍀