Build Super Fast & High Capacity Power Banks (130W) - DIY Fast Charge 15000mAh Power Bank

Рет қаралды 7,341

Күн бұрын

Пікірлер: 26

@ericklein5097 Ай бұрын

Yes, but you only used 5S so your ability to output at 20V is pretty much 0....once you factor in voltage drop (if you're pulling any decent amount of current) you'll drop from 21.0V to 20.0V really quick. In my experience you need at least 20.3V for most of these buck PD boards needs at least a few hundred millivolts over the output. The BMS you chose is definitely a decent choice as its simple and not as problematic as Daly BMS's Very cool how you adapted an Arduino to create a simple display with some of the more important information. Cell voltage and then calculating SOC based on lowest cell voltage is pretty simple with cobalt based lithium ion since its discharge curve is pretty linear. Using the overall voltage of the pack isn't the best way to go since your BMS will cut off once the lowest cell hits the BMS low voltage cutoff. Shouldn't be a huge issue if your cells stay fairly well balanced but once you start to get some deviation you might find near the bottom of their discharge they will deviate even further. Low voltage cutoff on the 30Q is 2.50V....if you stop at 3.00V you're missing out on 10% or 15% of the capacity. I personally wouldn't use the 30Q but if that's what you had laying around for free then free is better than nothing....30Q definitely has some cycle life and capacity degradation issues that came from trying to squeeze 15A out of a 3000mAh cell. Since you're running it at a max of about 7-9 amps if both ports are outputting 65W it shouldn't be too much of an issue. It would be cool in the future if you could find the simplest way to measure voltage and current output at each port but I think thats going to involve working with the fast charge module you're using and not doing it externally with the Arduino I didn't realize that input board you used could do 5S charging which is pretty cool. I know there are some boards on Aliexpress for 2S/3S/4S charging. When you look at getting a spot welder keep one thing in mind. Spot welding is entirely dependent on your power source: using a TRULY HIGH C RATE LIPO (that "100C" rating bullshit is all nonsense) SUPERCAPACITORS (watch out for all the used caps on Aliexpress, you get what you pay for) OR A HIGH C RATE LIFEPO4 LIKE A123 OR HEADWAY. You can use the simplest $20 PCB so long as the mosfets on the board are 300A-500A mosfets and there are 6-10 of them. Then you also want to skip the stock 10AWG leads for attaching your power source to the board and your weld pens/electrodes. I use 2 AWG to connect my Headway or A123 batteries to the board and 6 AWG silicone wire for my welding pens. You can make electrodes out of solid copper wire but the proper alloy to use is actually an aluminum/copper alloy. It's all about having a package that has low IR...you're aiming for single digit IR from power source to electrodes...3-7 milliohms is usually ideal. A 16Ah/20Ah Headway/A123 battery does pretty good but when I tried to parallel 2 20Ah A123 batteries I blew the mosfets on one of my JQ-DHJ02B boards...definitely one of the better boards for the money right now if you don't want to DIY your own (There are Aliexpress listings for mosfet boards for 8/12/16/24 etc mosfets of your choice...I like the IRL40SC228...then you'd need a control board like the 7Y320 which is meant for supercaps...for supercaps I'd recommend 2S2P minimum if you buy used caps from Aliexpress...they sort them by internal resistance and then sell them accordingly so don't buy the cheapest 3000F 2.8V caps you can find) There are a bunch of bidirectional boards available on Aliexpress, I mostly use Feb 22 store. Makes life a lot easier and most of them are either buck only (so you'd want a 6S or 7S battery probably) but some like the IP2368 are buck boost and meant for 3S to 5S with 4S probably being the most common. A 4S2P pack of 5Ah 21700's makes one hell of a good sized powerbank and with most 5Ah 21700's having a 10A or 15A rating they can easily handle 200W worth of output if in 2P. Whatever you do avoid the SW2303 IP5501 boards, they are garbage. My channel has a couple videos (long and boring) that go over a lot of the options out there and what I think of them.

@milobydesign 7 ай бұрын

I have a kweld. It changed my life forever. I hope you'll be able to get one soon. You'll love it. Worth every penny.

@Djambo57 7 ай бұрын

I was thinking about getting something smaller like that... I once borrowed a larger spot welder from a friend but it kept tripping my circuit breakers... The current spike was too high while turning it on. I also saw a bunch of battery powered welders online and I actually did use one of those before and it was quite good. They are around 50-60USD which is not bad

@beachcow1650 7 ай бұрын

the thing blurred at 1:34 looks suspicious lol also this video was really good, and the end product was amazing!

@Djambo57 7 ай бұрын

Haha, thanks! Looks suspicious indeed

@rydjaradat 12 күн бұрын

good Job , But, how is your battery balance holding?. As using permenant voltge dividers will ultimately debalance the battery cells, "yes you have a BMS that will balance the cells at the " but it is a passive balance, so if 1 battery is fully charged at 4.2 volts and another battery is at 4 volts and the charge current is still at lets say 250 mA(depends on how bad are the cells voltages are far apart, the bigger voltage difference the larger the current) the BMS will discharge the full battery at a current detemined by the discharge resistor "usually 100 mA", So the full battery is still being charged at 250 - 100 = 150 mA , when this battery reaches 4.25 volts the DW01-A protection IC will disconnect the whole pack from the charger/output, so you will have a battery at 4.1 volts (BMS keeps dischrging the full battery till 4.1 volts) and another at 4.05 volts, and this may worsen over time.

@nixon275 7 ай бұрын

Amazing work dude, as always. 💪

@danielkormendi8816 4 сағат бұрын

What happens if you charges the bank while it charges your notebook?

@Foton0154 12 күн бұрын

these chargers modules are cheap but they do not have good power quality, they have quite high ripple voltages around 250-300 mVp-p, the best way to reduce it is to solder a capacitor at the output aditional 220 or 470 uF do the trick and we get under 100mVp-p ripple when powered directly from 4s battery

@gamereditor59ner22 7 ай бұрын

Ah sweet!!

@Djambo57 7 ай бұрын

Thanks!

@gamereditor59ner22 7 ай бұрын

@@Djambo57 You welcome!!

@misterinfinity4076 7 ай бұрын

Why are you using different kind of cells? Is this safe? I have almost all the parts laying around, except from the usb-c output//power delivery trigger boards. I've thought about building a 5s power bank for a while, but i am concerned about the quality of all this type-c boards. I've seen some horrors while browsing alliexpress, and i've even got some that completely disregard every protocol/handshake. are you confident enough to use them to charge phones and laptops?

@Djambo57 7 ай бұрын

You should never use different cells! Looks like a forgot to mention that. I did use same ones but in some shots I had different ones just to show what I'll be using. I've used this modules for quite some time now and I didn't have any problems. They do have a bit of noise but they work, I'm not sure how I could test them better. I drained the whole power bank from a 100% to 0 in a single use multiple times and the modules did get a bit hot but other than that, everything went right

@duggrein409 5 ай бұрын

Great work

@Braven36 15 күн бұрын

Would it be hard to convert to us ac power instead of batteries. I hate how my multiport charger can not charger more than one device at fast charging.

@abidhussain9229 2 ай бұрын

I made the same, can you explain how to calibrate the voltage, i tried but the display always showing same voltage during charge and discharge, sure im doing some mistake. Kindly assist. Thanks in advance

@smartcookie_ibrahim4542 8 күн бұрын

What if I use each battery 3300mah ?

@barrydwaynethomas Ай бұрын

Hello, This is great! Do you have schematics/diagrams for the wiring?

@emiljanduka51 7 ай бұрын

if the cells are connected in series that means only 3000 mah

@Djambo57 7 ай бұрын

yeah it's 3000mah, 63Wh, I said it's 15000 only in power bank terms since most of the power banks on the market use a single cell inside and the capacity is the first thing you see on the box.