I must say Gil, for us QRP mountain top and park activators, you are the wind beneath our wings. Your video posts inspire and encourage us to try new things and to warm up the ether!
@RadioPrepper4 жыл бұрын
Thank you! Glad to be of some inspiration :-)
@TheDgdimick4 жыл бұрын
Gin, you SO need that 3d Printer. You're the one that recommended the Ender 3 to me, and I've been happy with it for 8 months.
@RadioPrepper4 жыл бұрын
And I still need to buy it! Darn, you beat me to it!
@TheDgdimick4 жыл бұрын
@@RadioPrepper I've bought 2 so far, and normally they are running pretty much all the time, except this week, I'm studying for my Extra Test on Saturday.
@ianboard35553 жыл бұрын
Completely agree. I bought one a couple of months ago and have been super happy with it. I like the fact that you can start with the basic model and upgrade it easily (better controllers, extruders, etc...).
@Adam-qd8jh Жыл бұрын
I decided to make this design and it worked really well for the cw range on the 40 meter band. Using 29 feet of speaker wire and a 32 foot counter poise. Though I haven’t heard any voice, my water fall on my SDR was packed with cw. I live in between two hills at the bottom and get really bad propagation. But This was my first antenna project after 2 years of messing around with the balun that came with the nooelec SDR. I think I just need to get my antenna higher or lengthen it as I only put it up about 15-20 feet. But I’m excited because I’ve never seen so many signals before. And also I tried using it at night so maybe this is why I haven’t heard any voice on the band. But I can tell this Antenna will pair perfectly with my QRP cw pixie. Thank you!
@RadioPrepper Жыл бұрын
Make sure you check the SWR if you transmit with it. You probably will need a tuner..
@richardcooper384 жыл бұрын
Gil, First off I'd like to thank you for all your efforts in publishing these videos. They have provide a huge amount of instruction for me. I think I've bounced around almost every antenna type for my situation. My wife and I live in our 38' diesel motorcoach. There's limited space for antennas. I will be mounting a screwdriver antenna that I've had been dragging around for years but I've always have had reservations about it's performance. I've read and have listened to almost everything about these EFHW antenna systems over the last couple of weeks. I've been trying to figure out how to utilize a half wave length piece of wire and what I could do. One of the comments from another channel, he had mentioned that he put one of these antennas in his attic running all over the place and still achieved great performance. With this in mind I'm going to try to run the antenna wire from front to back several times and see how this will work. At this point I've got fairly good confidence that it'll perform well for my situation. Have you strung up anything similar with limited space in your trials of ham radio? Looks like most of your CW'ing is out in the beautiful open country. I look forward to your upcoming videos about these antennas. I need to get this put up on the roof of the coach and give it a try so I can get more sleep. Lol Steve Ellington put up a fantastic video of his studies on this antenna system. Well worth the time to watch. 73's Gil and thanks again!
@RadioPrepper4 жыл бұрын
Not sure, that is a unique problem.. On a sailboat you have a mast.. You don't... The question is, do you want to operate while driving? Assuming that isn't the goal, honestly, a HWEF on a fishing pole type mast will serve you best, vertical or inverted V. I don't think it will work folded back and forth, but sometimes weird things happen in radio...
@richardcooper384 жыл бұрын
@@RadioPrepper Gil, Being able to operate while driving isn't going to happen. Maybe on VHF. I'll have to give it a try and see. If nothing else I'll be able to throw it into a tree when trees are handy. I wouldn't mind if this floated and had a mast. Lol. If I was a able we'd be sailing the high seas years ago. I'll let you know how it works out.
@OH8STN4 жыл бұрын
This was a magnificent video Gil, thank you for sharing 👍
@DrenImeraj4 жыл бұрын
You should consider getting a step drill bit. They are extremely effective for opening holes in plastic boxes. Thanks for another great video!
@RadioPrepper4 жыл бұрын
I have one, but I need a smaller one!
@n8nkqrp5954 жыл бұрын
It's all about Al value and thus the minimum usable frequency of the unit. And to a secondary matter- self-resonances of the UNUN with no load connected. T106-2 has an Al value of only 135, severely limiting it's low band use, as you mention. For what it's worth, the Al value of the FT140-43 is 885, 4 times that of the iron core, giving you 16x the inductance per turn. Much to consider. 73
@RadioPrepper4 жыл бұрын
Great info thanks!
@richardwhitcroftkc3rrw632 жыл бұрын
Gil.... your videos are always entertaining and educational.
@BarefootBeekeeper2 жыл бұрын
A stepped bit makes a better job of holes in plastic boxes than a twist bit, and can be used by hand, without a drill.
@jamdiversified96982 жыл бұрын
Quick tip, If you want to get hot glue off of something, spray it with isopropanol (IPA) and it will come right off clean.... From smooth surfaces at least.
@riaanmaree11324 жыл бұрын
It's been more than 24hrs and we're all anxiously awaiting the test video! ;-)
@RadioPrepper4 жыл бұрын
It's coming!
@ratfunkblue4 жыл бұрын
I have really enjoyed your videos. I am a newly minted ham. Got my general two weeks ago. I am now building the the earchi endfed for HF thanks to your videos. You are definitely my KZbin Elmer! Cheers! ~ KI5JZV
@RadioPrepper4 жыл бұрын
Glad to help!
@raulponce62764 жыл бұрын
Nice! I really hope it works! I also bought one and it arrived for me these days. It is a very low permeability (ur = 10) powdered iron specified as low losses in "all frequencies" (??). I have been researching, and it really makes sense that it is a core with lower losses at high frequencies, since the material allows less effect of magnetic hysteresis and circulation of Foucalt currents. The phenomenon is obseveed in induction furnaces, where the core must necessarily produce heat. conversely, especially in QRP, any loss value becomes significant. than, this core would be better. In my case, I will have to wait a little longer to test because I live in an apartment on downtown. I wait for your opinion in another video too! haha
@RadioPrepper4 жыл бұрын
Wait for the second video in a day or two...
@g4okt4 жыл бұрын
'I just can't help myself...." Yes, I know that feeling! Nice vid, looking forward to the testing. I like to use type 61 ferrite for 10 and 6m. 73, Keith
@RadioPrepper4 жыл бұрын
61 would be the right choice for those bands yes. Maybe 52 for 10m...
@survivalcomms4 жыл бұрын
Cool beans ! The step drills (unibit) work great for plastic housings . When I have used a ground reference with an end fed it's really cool to see just how differently the antenna acts over varying soil conductivity. I have had good results with a counterpoise and a random length wire but the RX noise was greater. Thanks for sharing !
@RadioPrepper4 жыл бұрын
Interesting thanks!
@hobbyrob3134 жыл бұрын
YES yes yes this is not strange what happens here! drilling holes in this way requires for it! but don't say that these boxes are junk, that's not fair! ( And +1 for Denis Dimick!!! ) Greetings from NL Rob
@toddmathews78283 жыл бұрын
I've found that using a forstner bit works really well for drilling through those cheap plastic boxes. Sadly, it took me more than one box to discover this.
@andreVE4BK2 жыл бұрын
I use a stepping bit… slowly. Never had a breakage
@ssubaihi4 жыл бұрын
I am HZ1-si (Suhail) from Saudi Arabia First, thank you so much for this Great channel .. I heard that some (Core materials) have some advantages over others, Particularly in (Receiving mode) which let your antenna has less noise.. Perhaps That's is why some of the End-Fed producers marketing some of End-Fed antenna as a ((SWL End-Fed antenna only) with limited TX Power capability .. Hopefully you shed some light on such (the important secret) .. I say this because I made myself End-Fed Half-Wave antenna, it is very good antenna, I have no big problem in (Transmit Mode) as I can compensate for Far Away DX station with a little push of TX Power ... However, I am still struggle in Receiving Mode especially with some weak DX signals .. Besides, I don't have much (Horizontal space) for the "Wonderful Beverage Antenna" .. By the way ... Generally Speaking ... which is better in (Receiving Mode) .. (9:1 Un-Un*) or (49: 1 EFHW**) ? considering Both Antenna have the same Length @ same Band .. *considering a proper Ground or Counterpoise applied.. **Considering a proper Line isolation applied.. Please Help ..
@RadioPrepper4 жыл бұрын
That is a very good point. I did not test noise levels... The second video will be out soon.
@alexandretsilefski23084 жыл бұрын
Hello Gil. I enjoy your videos. The transformer you discribed for the CB band is working really well, I had contacts with Perpignan and London from the village I live, not too far from Strasbourg. Many thanks! Have a nice week-end!
@RadioPrepper4 жыл бұрын
Excellent!
@andreVE4BK2 жыл бұрын
Gil… if you identify your wires individually (you’ll need 2 markers) before you start winding, you will save time and effort at the end. 73 Andre/M0RAV
@milfamily1934 жыл бұрын
you're awesome! I watch your videos a lot. I actually ordered 3 of the 140-43's last week. They arrived in pieces! The seller didn't package them well at all. But, he loss. Ordered 3 more form a different seller. We will see. Hope it all worked out. 73s from KC2JDR
@RadioPrepper4 жыл бұрын
Better use them for a 49:1 transformer..
@user-mt2qn4yp8w4 жыл бұрын
Man that sucks when the box broke. Keeping fingers crossed that it works. Great video. Take care. , KG7LOI Clark. 73's
@tanglewoood2 жыл бұрын
Builders might like using a step drill with 1/32" steps. They are available from a number of sources including Amazon.
@rickmckee66982 жыл бұрын
Just use a step drill !
@RadioPrepper2 жыл бұрын
Yes, I have one..
@robthomas86803 жыл бұрын
great article - got the parts - building one now - thanks!
@ae1tpa92gwtom24 жыл бұрын
Gil, ur great, n everyone , im sure everyone likes the look on yr face, when u cant help yrself, u give all of us education, courage to do it, n ways to enjoy the hobby,.. good on ya,.. 73 my friend
@RadioPrepper4 жыл бұрын
Thank you! Always nice to hear :-)
@georgealbertacanadaeh10383 жыл бұрын
Thank you, Excellent! I always wanted to see how this was actually done! I have seen and read articles but actually seeing makes it all come together. Thanks again, George Alberta Canada Eh
@RadioPrepper3 жыл бұрын
Glad it was helpful!
@HKey_Root3 жыл бұрын
'Don't make one yet as I don't know if it works'. Brilliant. Love it.
@RadioPrepper3 жыл бұрын
Turns out, it doesn't!
@HKey_Root3 жыл бұрын
@@RadioPrepper 😂
@napomania Жыл бұрын
good job . next time try to use a conic drill hole 🙂
@davidsradioroom96784 жыл бұрын
I want to build an unum. Looks like fun and you get something useful from it.
@RadioPrepper4 жыл бұрын
Yep, wait for the second video to choose your toroid! Coming up in a couple days...
@jimthvac1004 жыл бұрын
Great Video Gil, I look forward to your comparison of these two 9:1 UNUN's using your new Minion. Lol of course we will enjoy the video regardless what radio you decide to test them with :)
@RadioPrepper4 жыл бұрын
The second video will be out in a day or two!
@markg6jvy1354 жыл бұрын
“Toroids, washers wingnuts and 22awg wire, everything to make a man happy” 😂classic line Gil 😂👏 I find a cone step drill sometimes prevents that snagging of fluted drill bits when going into thin material.? Great video as always 👍
@RadioPrepper4 жыл бұрын
Worst thing is, I have one!
@mikes68444 жыл бұрын
Try putting a clamp both sides of the box before you drill the hole as it should stop it from splitting on the basis you are not using too much downward pressure. Or use a vice. Another very useful vid, I can't keep up with you! Just finished building a 49:1 balun. Will be testing some EFHW wires with it over the weekend. We are still in lock down and will be for a while longer, BYOTA (Back Yards On The Air) for me. Conditions quite good for a little QRP. Take care... 73 de M0AZE
@RadioPrepper4 жыл бұрын
I should have done that!
@StephenFarthing4 жыл бұрын
You will find it easier, and safer, if you use a step drill bit rather than the ones you have. I've probably a spare one if you want it.
@RadioPrepper4 жыл бұрын
Worst thing is... I have one! Thanks though :-)
@johnk80914 жыл бұрын
Great instructions to build the 9:1 "OON OON". I still far prefer the 49:1 and EFHW. Looking forward to your testing video to see how the two compare
@RadioPrepper4 жыл бұрын
Me too..
@gordselectronicshobby38534 жыл бұрын
Step drills would b better to use as well as a reamer for fine cuts.
@chipandrews28924 жыл бұрын
Another awesome video Gil...thanks for sharing. I must say that I really enjoy your project/build videos! You explain what you are doing so very well and seeing you do it really puts the cherry on top. Thanks again! Cheers! De KL7CA
@RadioPrepper4 жыл бұрын
Thanks Chip!
@radioastronomy20014 жыл бұрын
Like always very interesting video. Thank you! You can test it by loading it with a 470Ohm (ideally 450Ohm) resistor and running antenna analyzer. It should show around 1:1 SWR across all bands. I used a yellow core (+-4cm in diameter) from an old PC power supply. It does work well from 80m to 10m. The materials seems to be "#6".
@RadioPrepper4 жыл бұрын
Not the 9:1. The 9:1 needs to be tested with a resistor in the 400-600 Ohms range. A 49:1 or 64:1 however is tested with a 2500 to 4700 Ohm resistor. See: kzbin.info/www/bejne/ZqupaJV6pNaefZY
@radioastronomy20014 жыл бұрын
@@RadioPrepper Normally you can not buy 450Ohm resistor but 470Ohm seems to be close enough where 400-600Ohms seem to be too far. I agree for 49:1 transformer you would need something like 2450Ohm but again you can not buy one exactly like it. Most likely you would have to combine 2.2kOhm with something else (330Ohm) or use 2.7kOhm. So I still think 470 Ohm is a good approximation when testing 9:1 unun. 470 Ohms / 9 = 52.2 Ohms. Where 400/9=44.4 (my "." is yours ",")
@ricktafied Жыл бұрын
@@radioastronomy2001 Use a pot and set it to 2450 ohms?
@radioastronomy2001 Жыл бұрын
@@ricktafied Good idea. Thanks.
@joecraft44093 жыл бұрын
Hey Gil, today I heard that it is not recommended that one use a RED toroid to make unun. I have to go back and read the article for understanding.
@RadioPrepper3 жыл бұрын
Well, it's not recommended but it works better so...
@robthomas86803 жыл бұрын
um - step drills - $12 on Amazon or your locate hardware - don't leave home without 'em! :)
@MrLittlmike224 жыл бұрын
great video as always - it woudl be greta to move up to 1:49 too!
@RadioPrepper4 жыл бұрын
I definitely do prefer 49:1 with a half-wave wire..
@jamescoffey52254 жыл бұрын
I have always found that when drilling into plastic (boxes) I use a smaller drill bit or a few smaller drill bits and then start drilling, gradually increasing the diameter of the hole until I get to the size of drill bit I need for the BNC or whatever attachment I am using. Could you have made better use of a metal box for the UNUN if you could procure one for a reasonable cost? I have never tried using a metal box for a balun or an unun. AE5ZX
@jamescoffey52254 жыл бұрын
Of course I am usually too lazy and end up just drilling a hole of the appropriate size in the plastic box, and then just hope for the best. 😊
@Steve-GM0HUU4 жыл бұрын
For plastic, I drill a small hole then use a reamer to enlarge to exactly the right diameter. This way you can make holes of any size (3mm to 13mm) with just one 3mm drill bit and a reamer.
@flipster72853 жыл бұрын
I love watching your videos. I am learning quite a lot and I am now starting to build a few things to play around with. I do have a few questions though, maybe you could help me get some clarity. 1) what would the max power be that I can put through this FT140 9:1 unun? If I want to go up to a max of 500w, would I be better off with a FT240-43 or perhaps 2 stacked FT240's? Unfortunately toroid cores useful for RF are not easily available in South Africa and they are fairly expensive when we do get them so I do not want to buy loads of cores that will not get used. 2) when it comes to winding...... Adam (K6ARK) built a small 9:1 on an Ft50-61 but he does not use 3 seperate wires, he winds that with a single continuous wire. (I built that qrp antenna and it works really well). Would that same technique work for bigger unun's or would it be better to use the seperate wires and solder them together after winding? Looking forward to more quality lessons from Master Gil!
@RadioPrepper3 жыл бұрын
All right: 1. You don't build a 9:1 UNUN, which is for random wires with a 43 material core. Those are for 49:1 or 64:1 and half-wave wires. Watch the following video:
@RadioPrepper3 жыл бұрын
kzbin.info/www/bejne/ZqupaJV6pNaefZY
@RadioPrepper3 жыл бұрын
If you want to build a 49:1 or 64:1 for a half-wave wire, you will need to stack three FT-240-43 cores. I do not recommend using a 9:1 with a random wire for high power.
@RadioPrepper3 жыл бұрын
2. Yes, but need to test... 3. 500W is useless. Anything above 30W is a waste of electricity and not needed a vast majority of the time. Invest in antenna building materials and knowledge instead of an amp.
@warplanner8852 Жыл бұрын
Gil, French don't say "merde" anymore? 😅 For the bigger holes, use the a reamer, Gil. A little more work bit minimizes the chance of shattering. 72/73 de William, k6whp dit dit
@oobihdahboobeeboppah4 жыл бұрын
The Fairite type 43 is not the best material for the lower bands on HF. If you look up the specs at Palomar Engineers you will see that type 43 is better from 20m up possibly as high as 6 m. Type 31 is a better material covering 160 meters to 6 meters. Type 41 will work but not as well.
@RadioPrepper4 жыл бұрын
In theory yes, but in practice, everything I have ever found that works points to 43, 52 and 61 for 80 to 6m, with 31 used for chokes. Maybe the choke vs transformer is the difference...
@oobihdahboobeeboppah4 жыл бұрын
In recent months, I built 9:1 ununs using both. Afterwards, I used a 50Ω dummy load at the output of the unun, and my analyzer at the input. What I found was that in both units, the response curves almost paralleled the Fairite specs exactly. I've used both for QRP, and both work, though the 31 works better: Louder signals on receive and better signal reports on transmit. I'll have more time to test with the warmer weather. Ahhhh, the fun of Amateur Radio!
@Steve-GM0HUU4 жыл бұрын
@@oobihdahboobeeboppah just wondered please - on which bands did you find the 31 was better?
@mortimersnerd8012 жыл бұрын
@@RadioPrepper Your correct Gil...and Palomar sell 31 material specifically for common current and noise chokes... other than 160 and maybe 80, meters... 31 material is not recommended for the high bands.. took in their seminar at the Yuma hamfest. in how they explained this.
@svtelos47263 жыл бұрын
Its possible to punch holes in thin plastic, with an ordinary hand hole punch. A single, not the triple for notebooks. Or, for thicker plastic, a leather hole punch. much cleaner and less scarier than watching Gil and a drill press.... :) !!
@RadioPrepper3 жыл бұрын
Not that kind of plastic but those work very well on Altoid cans!
@svtelos47263 жыл бұрын
@@RadioPrepper Then, we should put a nice small drill press vice on your Amazon Wish List for Xmas! Thanks for your videos. I just got my General License and am looking forward to hearing you on the radio. Alas, Im in San Diego. Your vids are both entertaining and very instructive. Thanks. :)
@RadioPrepper3 жыл бұрын
Thanks! I have one but it's up North at my parent's...
@Ryo_Saeba4 жыл бұрын
Bonjour, je vous ai entendu au col de coursegoule alors que vous étiez au col de vence. Vous avez donné l'adresse de votre chaine, je me suis donc permis de vous écrire pour vous dire le bien que je pense de votre chaine et que la liaison avec un petit talkie était sans fioriture
@RadioPrepper4 жыл бұрын
Super merci! Je suis de temps en temps à l'écoute sur le relais du Mont Agel et Vial..
@riccardomilan Жыл бұрын
Thanks so much Gil! is it mandatory to remove the insulation before join and weld the wires correct? I'm doing a similar UN:UN with 16:1 9:1 and 4:1
@RadioPrepper Жыл бұрын
Hi, oh yes.
@AndrewBryantPianoTuner Жыл бұрын
When you twisted the 2 wires together did you remove the insulation ?
@rickmckee66982 жыл бұрын
An FT140-61 core works much better 10 thru 80 meters.
@jamesgeorge1709 Жыл бұрын
Get yourself some step bits you'll never go back to metal boring bits.
@19134ANDY3 жыл бұрын
Nice video, do you have one on how to make a 6:1 unun
@RadioPrepper3 жыл бұрын
I have one on the 9:1.
@mabo48484 жыл бұрын
TNX !
@scottcarter99754 жыл бұрын
Another good video Gil. Thanks. Question: I have a spare FT-82-43. Do you think it would work for a 9:1 for portable up to 10 watts? Thanks, Scott kw4jm
@RadioPrepper4 жыл бұрын
I will be able to tell you in a few days... Wait a bit... I would make a 64:1 transformer...
@WillemvanderHouven4 жыл бұрын
Nice video Gil, but could you explain te windings again with a total wind of the emailed copper wires i count 8 turns ? at 5:30
@RadioPrepper4 жыл бұрын
Count the turns on the inside of the toroid... Every time the wire goes through the code is one turn.
@AndrewBryantPianoTuner Жыл бұрын
When you twisted the 2 wires together did you remove the insulation or do you leave it in place ?
@RadioPrepper Жыл бұрын
I left it.
@carlossilva.k2wc.5424 ай бұрын
First, thank you much for sharing your videos with all us, I have a quick question, How much power can this core hold in digital modes (FT8)? Is 30 or 40 watts okay?, Thank you in Advance,73 de K2WC
@RadioPrepper4 ай бұрын
Hi, 30 should be OK, though with FT8 5W is enough. BTW 43 material isn't good for a 9:1. Check my other videos. Use a #2 red core.
@carlossilva.k2wc.5424 ай бұрын
@@RadioPrepper Thank you for your prompt answer, your are talking about the T200-2 toroid?
@RadioPrepper4 ай бұрын
Yes, or T130-2. I don't remember which one I used, it's in a video..
@corbeijersbergen99994 жыл бұрын
Gil, don't blame the cheap plastic box, blame the wrong type of drill..
@RadioPrepper4 жыл бұрын
Or myself.. ;-)
@putraperdana4941Ай бұрын
Can this balun be used as a rendem antenna to listen to SWL...sir...?
@RadioPrepperАй бұрын
Yes, it is for a random wire and will help reception, but better use a T-130-2 toroid.
@midwestavaitionmx55034 жыл бұрын
I’m brand new to hf, love the information in all of these videos. Also most interested in portable setups. Couple of questions, Do BNC and so239s serve the same purpose? Where do you get your materials for your projects? Thanks 73deW0DJW
@RadioPrepper4 жыл бұрын
Hi, Ebay.. BNCs are just smaller and easier to use; same purpose.
@Pauldeva4 жыл бұрын
What are dimension of the box pls, '73 de YO2MMJ
@RadioPrepper4 жыл бұрын
50x80x26mm.
@luismirandakunert34754 жыл бұрын
Nice, congrats DO you know where can I get(buy) a set of this toroids to make inductance as my pleasure? Thank you
@RadioPrepper4 жыл бұрын
I get them all on Ebay..
@thierryruiz92054 жыл бұрын
Bonjour Gil, très bonne vidéo sur la fabrication de transformateur, aurais tu la possibilité de joindre les liens pour l'achat des toroïdes, merci d'avance, 73 F1RJC
@RadioPrepper4 жыл бұрын
Sur Ebay, fais une recherche, il y en a plein...
@thierryruiz92054 жыл бұрын
Bonjour Gil, je viens de le faire, j'ai trouvé mon bonheur, merci Thierry
@tackanderson42702 жыл бұрын
How can you use a multi-meter to test "short" when all your wires are touching and already shorted"? Unless the "lacquer" wire coating is enough to separate them and keep them from shorting out?
@RadioPrepper2 жыл бұрын
The enamel does insulate the wires but the circuit itself is such that everything is a DC short, so a multimeter is useless. It is however not a short for AC at the intended frequencies.
@tackanderson42702 жыл бұрын
@@RadioPrepper Assuming those frequencies are isolated (in bandwidth). I'm assuming this is what you meant as "intended frequencies". However, once ground is introduced to A/C, a short results, even an isolated ground (not sure of a radiated or ground plane). So this means under operation, those wire must be isolated? Testing however, must be done with an O scope. I do think you said that the multi M would be useless, so point understood.
@RadioPrepper2 жыл бұрын
Actually I should have said "the turns are insulated," it really is only one wire... See my construction videos...
@tackanderson42702 жыл бұрын
@@RadioPrepper Sounds great....
@calvinlong12652 жыл бұрын
Do you know if you can safely use an unun on a dipole?
@RadioPrepper2 жыл бұрын
You would not use an UNUN on a dipole, as it makes no sense to do so..
@daveduffy22924 жыл бұрын
In some vlogs I noticed that they use insulated wire. Does it make a difference
@RadioPrepper4 жыл бұрын
Not with material 43. Note that enameled wire like I use is insulated.
@Subgunman5 ай бұрын
Old joke about thread lockers, "Cross threading works better than locktite". NOT! I found that buying and using the longer and narrower step bits will not destroy plastic cases, the fatter and shorter step bits will cause cracking of cases, steps too large.
@HKey_Root3 жыл бұрын
Actually could someone explain why this isn't a balun? Still learning.
@RadioPrepper3 жыл бұрын
BALUN is balanced-to-unbalanced. UNUN is unbalanced to unbalanced. Example: An end-fed wire is unbalanced, coax is unbalanced, so you use an UNUN. A dipole is balanced, coax is unbalanced, so you use a BALUN.
@HKey_Root3 жыл бұрын
@@RadioPrepper Of course it is. My bad. So twin flex from say a homemade Magloop would need a balun? 9:1?
@RadioPrepper3 жыл бұрын
What is twin flex? Are you sure you mean a magnetic loop, not a regular loop? Mag loops don't need impedance matching other than the big capacitor in the loop...
@HKey_Root3 жыл бұрын
@@RadioPrepper We're now talking at cross purposes. Thanks for your input.
@captainmarvel60314 жыл бұрын
Thanks for the video! One question, do you know what guage wire to use for it to handle 100 watts, or would I need a different toroid also?
@RadioPrepper4 жыл бұрын
It should take 100W, 1mm wire.
@barrykery11753 жыл бұрын
@@RadioPrepper The wire can easily handle 100 plus watts. The heating of the core is the limiting factor. Depending on what UnUn or balun you make, I've already run 1500 watts using an FT 140-43. Yet a 64 to 1 UnUn for a HWEF won't handle more than 50 watts without getting hot. Barry, KU3X
@RadioPrepper3 жыл бұрын
And risking permanent damage...
@laurentboussuge73684 жыл бұрын
Bonjour merci pour vos vidéos pouvez-vous la faire en français ?
@RadioPrepper4 жыл бұрын
La seconde sera aussi en Français!
@laurentboussuge73684 жыл бұрын
@@RadioPrepper merci
@technicmasters79362 жыл бұрын
Does this work with FT14-43 toroid or would i need to have a different number of turns? And if so, how many?
@RadioPrepper2 жыл бұрын
No, a 9:1 does not work well with an FT-140-43. Use a T130-6.
@technicmasters79362 жыл бұрын
@@RadioPrepper Probably just a typo, i meant FT14-43, i think i have a T130-6, ill give it a try, thanks
@RadioPrepper2 жыл бұрын
I never heard of an FT14-43... See the EARCHI (Hawai Radio Club) pdf file on the matter...
@technicmasters79362 жыл бұрын
@@RadioPrepper oh, sorry FT114-43
@technicmasters79362 жыл бұрын
@@RadioPrepper Would FT114-43 work?
@expert2444 жыл бұрын
Now I want to make an UNUN.......
@RadioPrepper4 жыл бұрын
Make a 49:1 transformer rather..
@harrymudd65472 ай бұрын
It's only eight turns.
@RadioPrepper2 ай бұрын
And?
@harrymudd65472 ай бұрын
I thought they said it had to be 9 turns?
@gilgsn2 ай бұрын
I don't remember, but 9:1 does not necessarily mean nine turns..
@harrymudd65472 ай бұрын
@@gilgsnI'm just trying to understand how this works. It looks like 8 turns to 16 turns. How do i get 9 to 1 impedance match from a 2 to one turns ratio?
@RadioPrepper2 ай бұрын
@harrymudd6547 I don't know on a trifilar transformer, only how to calculate it on a regular bifilar transformer...
@M0RMY4 жыл бұрын
Gil Brilliant as usual. I really enjoyed this. I have emailed you a message about a project you may be interested in conjunction with Callum DX Commander. Tom M0RMY
@RadioPrepper4 жыл бұрын
I'll check that address thanks!
@warplanner88523 жыл бұрын
Gil, I am told that you can TWIST the wires with no adverse effect. I am going to build a one and I will report back. de k6whp
@kennethschultz64654 жыл бұрын
Hot glue ain't water tight .. you truly want ppl to fail
@RadioPrepper4 жыл бұрын
It doesn't need to be watertight. This is for temporary portable operations. Even for a permanent installation, these boxes should be vented to avoid condensation.
@kennethschultz64654 жыл бұрын
So you are a Fan !! Well I'LL never be !! I tryed 5 difrent designs Not one of Them worked in any satisfictory way !! It's a crappy antenna !! In any way.. waste of time
@RadioPrepper4 жыл бұрын
Fan of hal-wave end-fed antennas, not random-wire antennas with a 9:1 UNUN... What kind did you try and how?