Building a Miter Saw Station PACKED with Features!

  Рет қаралды 1,004,273

Michael Alm (ALM FAB)

Michael Alm (ALM FAB)

Күн бұрын

Пікірлер: 565
@AndyJame-eu2qr
@AndyJame-eu2qr Жыл бұрын
the author does like to from scratch, shaping and trimming wood from large blocks into fine finished products. kzbin.infoUgkxD-QRFQz730FJEh4f9BYSf-nkIMIC9hL_ as another reviewer mentioned, most projects require a lot of high-dollar equipment that most of us dont have the room or budget for. But, knowing how to do these things, even if we wont be able to practice the full stack project, is still great.
@dan__________________
@dan__________________ Жыл бұрын
I built a semi mobile miter saw station. One of the best additions I made to it was adding an inlayed measuring tape about 1/16th below the surface. I accomplished this by routing a groove and inserting a long adhesive backed magnet that you can get in rolls from amazon. I then laid in one of those measuring tapes used to attach to tools such as a table saw. The beauty of using the magnetic strip is that you can tune and fine adjust the ape measure because its not permanently adhered to the station, only stuck down via the magnet strip. I then added an acrylic tab to the adjustable stop that has a shallow cut in it which is filled with red marker. This is a simple way to make a cursor to line up the stop. I also added a flip to the stop and an adjustable miter stop but I wont get into that here.
@jeremyspecce
@jeremyspecce Жыл бұрын
More and more the stand alone toe kick base makes so much more sense than building a toe kick into each cabinet box. To be able to level the whole thing and then work off of a common level base simplifies things so much, especially if your floors are less than perfect.
@FraterAleph
@FraterAleph 6 ай бұрын
I agree but the way he used those little blocks with a single screw each to level it is nor nearly beefy enough
@AlanCart
@AlanCart 3 ай бұрын
Are the toe kicks screwed to the wall/floor or just left loose on the floor? Same questions about the cabinets to toe kicks, it didn't seem like they were screwed together.
@MichaelAlm
@MichaelAlm Жыл бұрын
FYI the plans for this build are now available at www.almfab.com/store/plans they include plans for the flip-top lathe, and if you don’t have a lathe, it explains how you can build a second drawer cabinet. Also if you have a different miter saw, the plans explain how to modify for your set-up. For those who give it a go, enjoy the build, and thanks for supporting my channel!! 🙌
@jimmygiannakis3638
@jimmygiannakis3638 Жыл бұрын
As a retired old fart getting into a wood working hobby it's mind boggling watching your skills. I know I could never live long enough to acquire a minute fraction of your ability but your videos are still super inspiring to watch.
@ROBTAT2
@ROBTAT2 Жыл бұрын
There’s still plenty of cool things to make without having 20 years of experience. There’s really cool pattern plywood you can make with basic designs.
@adamb0mbz
@adamb0mbz Жыл бұрын
You can do it! Just time to see how deep the rabbit hole goes
@jeremyspecce
@jeremyspecce Жыл бұрын
Just start. Make ANYthing. Get out there, and do it, start small, get the tools as you need them and just have fun.
@dannyarcher
@dannyarcher Жыл бұрын
I’m in that camp mate. Don’t think I’ll ever have this level ability but I’m planning on having fun spending my retirement money on wood and playing about. Only thing I’m a touch nervous about is buying a table saw as kick back seems to be a real thing lol
@WillTilton
@WillTilton Жыл бұрын
@@dannyarcher I avoided table saws for years for that reason. Got one a few years ago. I just try to be super safe, never had a kickback. Honestly think you'd have to do something really stupid to have one. I worry more about chopping off a finger so I always have push sticks for everything.
@brendangrimace
@brendangrimace Ай бұрын
I can’t tell you how many times I’ve seen KZbinrs say “this is the easiest way to do drawer slides,” only for it to be ultra-convoluted. Your method (for both matching the heights, and for setting the 1/8” reveal) is all the more complicated that the task ever needs to be. Thanks for all your fantastic content!
@Fixthisbuildthat
@Fixthisbuildthat Жыл бұрын
Killer miter station, Michael! And those outro beauty shots are straight 🔥
@MichaelAlm
@MichaelAlm Жыл бұрын
Thanks Brad!!
@marchelovtiberiualexandru7062
@marchelovtiberiualexandru7062 Жыл бұрын
@@MichaelAlm foam inserts for all the drawers! that would look amazin g with all the work you put inm the mitter station
@jeremyspecce
@jeremyspecce Жыл бұрын
Definitely pretty nuts with the dynamic lighting 😮
@m.d.e.845
@m.d.e.845 Жыл бұрын
@@MichaelAlm next time you pull the tinfoil out, just say ‘if you know you know…’ 😂
@Limosical
@Limosical Жыл бұрын
19:08 - When cutting metal it's important to get a good bite into the material, if you are pressing lightly then the heat is probably not leaving in the waste swarf but allowing it to spread to the blade, making the blade get hotter than it would otherwise. There's also the possibilty that you can press too hard and create extra heat too while also chipping/breaking the cutting edges. A good middle ground of pressure is required.
@jackknows6509
@jackknows6509 Жыл бұрын
Michael, this walk thru your growth is actually an excellent opportunity to show people like myself that highly skilled and talented artists like yourself started off doing things they felt worked for their immediate needs. As for myself, I just as soon not watch someone who acts as though they have never been in the novices' shoes, that they've never had to make something work until they could get better tools or more experience. Everyone starts somewhere, that first step and most do not pick up a tool and viola, a working project with no issues. So humbling oneself to show we are all learning is a good thing. Thanks, Jack
@erik.albrecht
@erik.albrecht Жыл бұрын
That tip on enlarging the hole with a forstner bit is incredible! Definitely a "why didn't I think of that" moment!
@triciac.5078
@triciac.5078 Жыл бұрын
Damn Michael!! That’s a gorgeous setup - even as a non-woodworking person I can totally see it! Also love the dust collection system. One of the reasons why I still watch your videos is that dust collection system. When I was 7 or so, my next door neighbor (and best friend’s) had a house fire due to the dryer and the excess sawdust in the garage. Love that you clean this up, not just for your lungs, but for safety in general.
@MichaelAlm
@MichaelAlm Жыл бұрын
Thanks Tricia!! Dust collection is a must!
@benwilkerson1188
@benwilkerson1188 Жыл бұрын
@@MichaelAlm what dust collector were you using under the cabinet? I don't see it listed in the description but curious what you were using.
@allenramirez2778
@allenramirez2778 Жыл бұрын
I've been outta the game for a while, moved into my old house that is paid off but it's built in 48,i have a lot of renovation to do and closed my mechanic shop, started a job in casino to build up some cash, and now I'm very inspired by this video to build the best woodshop and single bay hangar style garage for my vehicle work with a lift that I've ever had! Thanks Michael, this is the one that I needed, first the woodshop, then everything else will fall into place and hopefully my job will let me work part time only when I'm ready if not it will be only my businesses, I closed the doors on them but never retired them
@danboyett4385
@danboyett4385 Жыл бұрын
I bought the plans and built the outfeed table… love it. I bought the plans for the under-saw cabinet… halfway thru that build… I can’t wait for the miter station plans to become available. I’ll probably put my own little touches so it matches the outfeed table and the under-saw cabinet though. But I love the design; great job.
@Jlinwoodjackson
@Jlinwoodjackson Жыл бұрын
All I’m gonna say is…. The J. M. Dawley mitersaw measurement rail and stop..,is hands down the best you can get… short of an automated one. You can get ONE aluminum extruded rail that is up to 8’ long… maybe 10’. The “stop system” is amazing, as you can put in MULTIPLE stops on the back of the rail, and the sliding stop , stops on them.. or can go past them. Say… for a cabinet shop that cuts a few measurements ALL THE TIME.. so, just put in stops on the rail system, and it will always be dead on! It’s the best!!
@robohippy
@robohippy Жыл бұрын
For the two angled drawers, for me, in keeping with the 1/8 inch reveal, I would put a 1/8 inch shim of hard maple or some hard wood, then wax the runner and the bottom of the drawer edges. They will slide as easily as the mechanical runners. Nice build. My lathe, well my big ones, would not work with a tip up.... My mini lathes yes.... I am lucky to have a lathe room and a flatwork room.
@frednoble3547
@frednoble3547 Жыл бұрын
I think only you out of all youtube could have turned a mitre station into such a beautiful work of art! Tool companies need to start recruiting you to design their show booths!!
@rcbax434
@rcbax434 Ай бұрын
You are the "This Old Tony" of woodworking. I like your small shop and how you have made it function better. Bigger is not always better. Great stuff.
@MichaelAlm
@MichaelAlm Ай бұрын
That's an honor! I love the size of this shop...
@orientalwoodworks
@orientalwoodworks Жыл бұрын
I work in the trim industry. I’ve only used two miter saws, the Kapex, and the Hitachi C10 FSH. It’s undeniable that the Kapex is more accurate but under powered (as all Festool tools are😣) The Kapex has zero travel out the back but the Hitachi has the slides that run out the back. Also, the Hitachi is more powerful. However, on the job site, you basically just said the Saw up wherever, not necessarily up against the wall when you have to worry about space. Just food for thought; I am not in any way trying to influence the way you buy tools for your shop. Great video.
@randallsmith7885
@randallsmith7885 8 ай бұрын
I love watching pros tape and float out drywall. Beautiful work!
@AngieWilliamsDesigns
@AngieWilliamsDesigns 4 ай бұрын
As I’m about to FINALLY build my miter station I had to watch this again. There are so many things that I picked up on this time around that I didn’t think about when I first watched. Glad I watched again.
@haydenbriggs
@haydenbriggs Жыл бұрын
Hey, just a tip. The Kreg jig has two little holes above the main hole for the hinges. They are there so you can just drill the holes for the hinge screws while the jig is still clamped in place! Hope this helps!
@Ghust2
@Ghust2 Жыл бұрын
I just finished a cabinet project & used the Kreg Jig for this. My hinges' holes didn't line up with the kreg jig ones, so might be that Michael had the same issue :)
@angellas.1314
@angellas.1314 Жыл бұрын
@@Ghust2 Many people have that issue. It’s nuts Kreg didn’t fix that. I had the same issue this weekend!
@chipmeister111
@chipmeister111 9 ай бұрын
This was so nice to watch. It's got the creative juices within me screaming to come out so thanks a lot. I'm purchasing a miter saw in the next month and have been searching for ideas for a station. You did an incredible job on yours. I could just sit around it and stare all day, never getting anything done. Thanks again.
@unclejim2048
@unclejim2048 Жыл бұрын
Good video Michael. Here's a tip for enlarging a forstner bit hole when you make one that is too small. Take the new larger bit (the size you want the hole to be) and drill a hole in a piece of scrap. Now place the new larger hole in the scrap, over the hole that is too small -- you can clamp it, hot glue it, brad nail it, stand on it or what ever is convenient. Now use this hole to guide the outside of the larger forstner bit instead of the center spur. Once the hole is enlarged remove the scrap piece. It's an old trick used to make door-knob holes bigger in old doors.
@Aethalops
@Aethalops Жыл бұрын
The narrow drawers next to the saw are a nice touch. The "toe kick" is a great foundation and makes life easier ever afterward. Just FYI it's actually called a plinth (See Encyclopedia of Furniture Making by Ernest Joyce). In my setup I put a small cyclone / small bucket in the cabinet before the vacuum. Much faster to empty.
@kevinetheridgemakes
@kevinetheridgemakes Жыл бұрын
The explanation of the drawer slide installation is really clear and seems a good idea. I’ve seen 100 different people do it, but this method seems to be one of the clearer methods. Nicely done.
@jasona2881
@jasona2881 Жыл бұрын
Michael, a quick tip on the Kreg hinge jig. There are two small holes on the inside ring for drilling pilot holes for the hinge screws. That removes the need to align the hinge to set the screws afterward.
@stradric
@stradric Жыл бұрын
Another: Maybe this is on newer models, but the plastic guide on the forstner bit on the jig has a twist lock so you don't have to un-chuck it from the drill every time.
@stuartmackenzie454
@stuartmackenzie454 6 ай бұрын
Might want to try attaching all hardware before assembling cabinet. Flat horizontal on workbench attach drawer slides then assemble cabinet. Work from drawer slide centre line for screw location. Great saw station
@Joadcressbeckler
@Joadcressbeckler 2 ай бұрын
You should be proud of those drawer slides. Great idea and execution.
@Toograced
@Toograced Жыл бұрын
Of course you already know this, but I thought I would confirm it all the same.... That was really amazing videography on the glamor shots of the stand and tool. As usual, you really have taken what use to be armature videos to another level. Very well done. Thank you.
@ncstudio333
@ncstudio333 Жыл бұрын
Don't worry about heating up your blade on aluminium cuts, the chips will take out basically almost all the heat and unless you're cutting like 6" solid round you can be almost as generous as with wood when chopping it.
@Arterexius
@Arterexius Жыл бұрын
Having been hit by those chips while cutting up a bunch of scrap, I wholeheartedly agree. That burned like hell
@justintomer2567
@justintomer2567 Жыл бұрын
While I agree that the blade heating up is not the issue, I've found that if you're too aggressive when cutting aluminum you tend to end up with some material sticking to the teeth, which can be difficult to clean and causes issues when cutting wood after the fact like more pronounced saw marks, increased tearout, and even burn marks if your blade is also a bit dull (which happens if you cut a lot of aluminum) overall it's just better to take your time cutting aluminum
@mbmurphy777
@mbmurphy777 Жыл бұрын
Moving up to a larger hose on the festool made a dramatic improvement on my dust collection.
@DrDsHere
@DrDsHere 9 ай бұрын
A suggestion for the shop: Put a dust collector point in front of the vacuum cabinet. Then you can sweep the floor dust easily into the vacuum.
@meperson
@meperson Жыл бұрын
That is more beautiful shop furniture than my kitchen cabinets 🙂. I also like how you mix Festool and Ryobi - no tool snobbery, skills speak for themselves! I do wonder if your vacuum is being starved for air exhaust being fully enclosed?
@thomaslong3947
@thomaslong3947 Жыл бұрын
As a younger wood worker, I appreciate the detail and craftsmanship. I've started building tables and stations for my company and videos like these give me great ideas. Thanks for the beautiful video.
@lawrencemay8671
@lawrencemay8671 Жыл бұрын
I’m remodeling my master bath, it has a 109 inch double vanity, with a center that is open for my wife to do whatever wife’s do to get ready for whatever. I replacing it with a more modern look. It’s built out of good quality cabinet plywood. So I’m going to build a base like you did, then level it. Take the doors off, and add drawers to it.
@matthewcraver9917
@matthewcraver9917 Жыл бұрын
re: baltic birch plywood. Two alternatives are apple plywood (mostly US-sourced) and eucalyptus plywood (Vietnam, Indonesia and Malaysia-sourced). I personally haven't worked with either but they are both stable hardwood plywoods.
@15harney1987
@15harney1987 Жыл бұрын
I started building my station very similar to yours. My biggest issue is that I’m using a circular saw and a level with clamps for straight cuts, so not everything is square. Add to that I don’t have a truck, so I have to get my plywood precut at Home Depot, ie also not square… shims and lots of checking and rechecking before screwing together are the name of my game. Thanks for the inspiration to finally get this going!
@lukebetterton
@lukebetterton 9 ай бұрын
I loooove the plywood being cut and shaped into handles, that's really smart.
@PK-ey9rt
@PK-ey9rt Жыл бұрын
Very nice work. I would add some small vents to the cabinet below the miter saw. This way, the shop vac doesn’t create excess pressure/heat in the cabinet. Might no be a big deal but better safe than sorry 😊
@ptrbltmech6288
@ptrbltmech6288 9 күн бұрын
that dowel on the oversize Forstner bit is a great Tip !
@robmcgrath5202
@robmcgrath5202 Жыл бұрын
OK, haven't finished the video yet but the hack with using a round plug on the Forstner bit to enlarge a hole was definitely worth the price of admission all by itself. Thanks for that. If the remainder of the video is as well explained as the first part then I will have learned a good bit when it comes to my own miter saw improvement.
@jasondoza1991
@jasondoza1991 Жыл бұрын
Ive been a carpenter for 25 years, and it looks very nice!! Hide away lathe is a cool idea, chop saw drawers are cool too. Im building my shop as we speak and i appreciate the ideas.
@jspin72
@jspin72 9 ай бұрын
Very nice build! However I will add the same small critique that I have with several of the miter stations I've seen. There's a lot of custom fabrication specific to this particular saw. I realize it's a Festool and should last a long time, but u just never know. If/when you have to replace it, there will be significant modification required to fit a new saw... unless the replacement is the same unit, or is shorter and narrower. I'm planning to make my shelf slightly deeper than the height of most saws, then shim the saw up flush to the top. The shelf will also be slightly wider than most saws. Then the only custom fab will be narrow fillers to bridge btwn the bench top surface and the edge of the saw base on both sides.
@hollyy1905
@hollyy1905 Жыл бұрын
i'm not actually a woodworker (though it is fun when i do get to do it), but I've watched years of your content and loved it!! i learn a lot even if there's no use for it personally, and watching the processes and explanations behind your projects are always so so so entertaining and valuable. love your stuff, Michael! it's great seeing you update your workshop :)
@corydauer
@corydauer 9 ай бұрын
Great job. I can't wait to finish my house build so I can build out a wood working shop. Thanks for the great detail.
@rangersmith4652
@rangersmith4652 Ай бұрын
Those "first drawers" are functional and obviously sturdy. I suspect they were also very cheap top make. That means good design.
@FeedMeAQuarter
@FeedMeAQuarter Жыл бұрын
I've got a couple of tips for you. I noticed that your Milwaukee drill dropped the hole saw as you finished drilling, that usually happens when you are on the corners of the arbor and not the flats. It's also a well known issue with Milwaukee drill chucks, which leads me to my second tip, the run out. Milwaukee drills have sloppy keyless chucks. But you know who don't? The Germans. There is a company called Rohm who makes machinist tools and they make a bolt on replacement for Milwaukee drills. They have the standard 1/2"-20, as well as the 9/16"-18 that they made specifically for the M18 Fuel drills. They're great, I had one on my 3rd gen Fuel and abused the hell out of it for several years before the drill got stolen. As far as the right angle adapter goes, they are great for occasional use but the internals heat up very quickly and shatter under heavy use. Just putting that out there in case anyone was thinking about trying to use one for drilling joists etc.
@kleckerklotz9620
@kleckerklotz9620 Жыл бұрын
This is the best Festool miter saw ad I've ever seen. I really don't understand why they don't sponsor you. SCNR. Well done, Michael. Greetings from Germany...
@hou-fungyuen4064
@hou-fungyuen4064 Жыл бұрын
This is absolutely incredible! The only thing that messes with my head is the draw pulls on the 2 patterned plywood drawers...as they are angled my head would think they open out at an angle rather than straight out so instead would've put the brass handles perpendicular to the mitre station itself rather than drawer face. Anyway it's no criticism at all as the whole thing is so on point
@Toograced
@Toograced Жыл бұрын
I was thinking the same exact thing when I saw it.
@CoachAndreaTyndall
@CoachAndreaTyndall 9 ай бұрын
I am in love...OMG...I need this! I love how the side tops butted right up to the chop saw. I'm going to redo mine and I will totally be incorporating that!
@subungulate
@subungulate Жыл бұрын
This is the second video of yours I watched. Your woodworking is excellent but I’m so impressed with the video production: voice overs, shot angles, editing, sound design, etc. I could watch you work all day. Keep up the great work.
@Golgafrinchamdent
@Golgafrinchamdent 2 ай бұрын
Great idea & execution of the hid-a-way lathe! Innovative ideas like that always catch my attention.
@clintstinytrailerconversio5560
@clintstinytrailerconversio5560 8 ай бұрын
I'm repurposing some really bad cabinets for my daughter, but it does have nice fronts and doors and my heart yearned for a new miter saw, but with the cost of the project I pulled out my old 12" Porter Cable. I only have to make 6 new fronts and will try an edge beads (might not be saying it right) for the first time and undermount slides for the first time, as well. I found Maxcut software that let me create a cut list and optimization for the 3 thicknesses of birch. Plywood is coming from Florida Southern Plywood; is prefinished and their prices destroy those of the big box stores.
@wonderwonder30
@wonderwonder30 Жыл бұрын
Your giggle at the end while revealing the lathe says it all! This is fantastic, wish I had your skills to pay the bills 😊😆
@haltz
@haltz Жыл бұрын
Super cool build. I hadn't considered putting a lathe in a flip top. Space considerations are what's stopping me from buying one, now I'm rethinking that. I'm a huge believer in building a separate toe kick and leveling that first. Just makes the rest of the job so much easier. We just did a 25 foot run of RTA kitchen cabinets in the original part of a house that's 110 years old, the floor was out a full inch over that span and leveling them independently was incredibly tedious, but some built ins we made custom for the living room we were able to put on separate kick and it was a walk in the park. Not a criticism here, I own a Foreman and use pocket holes regularly, but I don't understand why anyone uses them to knock cabinet carcasses together.
@MatthewBowe
@MatthewBowe Жыл бұрын
That forstner hole resizing trick might be the coolest thing I've seen in a while.
@thanatos66613
@thanatos66613 Жыл бұрын
I can't believe it's been a year since the tool wall video! I love your stuff.
@asa_2361
@asa_2361 Жыл бұрын
Hey Michael, not sure if anyone else has mentioned this but the Kreg door hinge jig actually has two drill hole guides for the hinge screws. Saves you from having to use the speed square. Always enjoy your videos!
@coreycrlsn
@coreycrlsn Жыл бұрын
Came here to say same thing. Also, you can remove the whole drill bit assembly from the jig, so you don’t have to unchuck the bit every time.
@Ron-FabandBuild
@Ron-FabandBuild Ай бұрын
Awesome job on the miter station! I have to laugh, I guess we all have that first miter station from scraps. Unfortunately for me, I am still using mine. It will suffice until I make the move into my permanent shop area. Then I will build my forever station. Very nice job, Love the special touches on the pattern plywood drawers. The entire build was really thought out. Great job. Thanks for the video.
@HLR4th
@HLR4th Жыл бұрын
Miter station envy! Outstanding. Loved the tip about the forstner bit when the hole intially made was not the hole really needed.
@woodfella21
@woodfella21 Жыл бұрын
I always look forward to the release and viewing of your videos. Your ability to define the video ratio of: How much do I explain vs. How much do I assume the viewer already knows or comprehends, is spot on. Just the right amount of clarity. There are three moments of irony involved in me watching this video just now. 1. That cast iron Delta beast was also my first power miter box. 2. I also recently designed a new miter box station for my new compound/sliding miter saw. (Although mine will be portable.) 3. We share the same last name! Keep up the good work Michael! Sincerely, James Alm / Northern Illinois
@matthewmcmurtry6069
@matthewmcmurtry6069 Жыл бұрын
Here's what i love about your videos. i can watch them with the sound off, as i often do when i'm in class, and you can still understand the entire process, logic, and practical application. Truly that's a craft of it's own. Great job.
@bertv1205
@bertv1205 Жыл бұрын
You are gonna love the Kapex (I do!). Might I suggest you check out the Hookedonwood channel for his design for a super fence for the Kapex & getting a zero-clearance insert, either homemade or by Cauliflower (which I like a lot)?
@fatroberto3012
@fatroberto3012 6 ай бұрын
I wish you had drilled the mounting holes for the brass drawer pulls at an angle that had them line up with the direction of movement 😁
@JSCRocketScientist
@JSCRocketScientist Жыл бұрын
I always wondered how cabinets were leveled. Your method worked very well, since you didn’t have to do further leveling!
@lancesmith5645
@lancesmith5645 Жыл бұрын
very nice man. its always nice to see the efforts of organization combined with experience gained come togather so flawlessly. that is a nice workstation.
@nathanielsnyder1323
@nathanielsnyder1323 Жыл бұрын
I know its more cost but pairing your kapex with a festool dust extractor would make the dust collection that much better.
@AtomicSneeze1
@AtomicSneeze1 Жыл бұрын
great project. I'd however never be able to use those flat drawer pulls. No matter how careful I'd be, I would forever be catching myself on them and end up with cut divits in my arms and legs. I learned the hard way. In the shop only round and/or flush handles on all drawers and cabinets. preferably flush mount as anything that sticks out is a catch magnet for EVERYTHING. LOL
@gregorycampbell1148
@gregorycampbell1148 Жыл бұрын
Who makes that Shopvac? Great build!!! Waiting for the newsletter for plan release.
@jewdd1989
@jewdd1989 Жыл бұрын
This is amazing! I love the details of hidden extra storage, it’s function is just as nice as how it looks and I can’t wait for this secret video you have of your new amazing lathe… wtf how cool is that flip top integrated into your mitre saw station!!! The patterned ply fronts on both cubbies was a perfect touch and the quality of your ply, I’m still struggling to find locally but I’m in a small town… pushes me to address my nightmare of a garage. Always beautiful work, thank you for sharing and in such great detail and your knowledge is incredible!
@neilarmour4497
@neilarmour4497 Жыл бұрын
That forstner bit tip is game changing. Thanks for that!
@stephencracknell5077
@stephencracknell5077 Жыл бұрын
Tony give the tormek grinding system a try you'll not be disappointed. I also used and destroyed a few king stones before moving on to the tormek, remember it's all the same at the end of the day, sharp tools, but quicker.
@CheveeDodd
@CheveeDodd Жыл бұрын
Man, I used to have that same chop saw and I miss it like crazy. I've yet to find a compound sliding miter saw that is as accurate. That old saw was dead on every time. Oh, your station is beautiful. 🤪
@JesseHires
@JesseHires Жыл бұрын
Most of the folks I watch on KZbin live a good distance away from me. But I live in the same general area as you. It's fun to occasionally see locations I recognize like the lighthouse in your Jackery commercial.
@Brammm87
@Brammm87 Жыл бұрын
Gorgeous b-roll shots. Your woodworking skills grew over the last few years, but your video making one sure did as well!
@HobbyGarageDIY
@HobbyGarageDIY 4 ай бұрын
Wonderful work! It's good for the eyes to look at how you work 😍
@Olm9
@Olm9 10 ай бұрын
27:05 I think I would have preferred a one-hand operated drawer. I tend to bring something to the drawer to put back in one hand and open the drawer with the other hand. To open a drawer with both hands I need to put the thing down and pick it up again.
@kailuasurfing
@kailuasurfing Жыл бұрын
B roll is ON POINT my man
@dylandempsey6103
@dylandempsey6103 Жыл бұрын
I've heard mixed results on dust collection for the Kapex 120 REB. What are your thoughts? I've heard you need to slow the blade speed down and get a shorter 36mm hose to get decent collection out of it.
@smallberries
@smallberries Жыл бұрын
Nice work. Curious why you used a shop vac and didn't connect the miter saw dust collection to your central shop system? Maybe I missed the explanation in the video. Regardless, the whole thing looks very nice.
@JSCRocketScientist
@JSCRocketScientist Жыл бұрын
I did get a good laugh at your warming up tea on your Jackery in winter. It’s early February and here in Texas it’s 68 degrees and humid. Too bad it can’t power a portable A/C unit. But I can see the use in having a solar powered portable generator for powering devices. We get hurricanes here in Houston.
@Flippingdrawers
@Flippingdrawers Жыл бұрын
This beach carving looks very familiar😂 Love your videos mate.
@waynerudiger1756
@waynerudiger1756 Жыл бұрын
Nice miter station. Pretty similar to my absurdly overbuilt 20 year old one (yep, leared a bit since then). One question - do you plan to add self adhesive rulers to both sides? Those are a game changer for me, just as valuable as on the table saw.
@ThisTall
@ThisTall Жыл бұрын
I LOVE my Kapex, but my only complaint about it is they’re essentially useless at a 45° compound cut to the right side. The guide rail drops so low that it’s basically incapable of cutting anything thicker then 1-1/2. And I run in to this constantly trying to cut L-shape trim for cabinet crown and fillers.
@timhalleran3514
@timhalleran3514 8 ай бұрын
Wow!! Strong build Sir!! Great design brother😃
@jamespyacek2691
@jamespyacek2691 Жыл бұрын
Build the little drawers over size and cut the entire thing at once on the miter saw. Seems weird you didn't do that. Also I think it would look cool for the brass pulls to be parallel to the drawer, instead of perpendicular to the face. Opinions... you know, everyone has them. I'm gonna have to check out that patterned plywood!
@leroymellix5647
@leroymellix5647 Жыл бұрын
Hi, I have seen your structurally similar draw slides on verry old furniture, good stuff! liked your video!
@Codeyellow
@Codeyellow Жыл бұрын
Look at this! No clickbait title and a quality thumbnail with no weird faces or red arrows at 174k views. Thanks Michael! Raising the bar to Show everyone that they just need quality content!
@davidvoorhies812
@davidvoorhies812 Жыл бұрын
My brother needs to do this in his garage soon. Thanks for all the detail.
@jronmanbuilds
@jronmanbuilds Жыл бұрын
I used to use one of those right angle attachments for the drill. They are really handy to have and a very good value. In the last couple years I picked up the m12 Installation driver and it was a game changer. I just throw on the right angle chuck and/or eccentric chuck now.
@MrJohnBos
@MrJohnBos Жыл бұрын
Great build, I would apply a tape measure tape next to the channel inserts on either side of the saw for easy measurement of length using the stops.
@elivaughan1192
@elivaughan1192 Жыл бұрын
Walnut/aluminum and holy crap. That thing turned out gorgeous. I really didn't know where the aluminum thing was heading. Love it.
@scottcbarton
@scottcbarton Жыл бұрын
The Forstner bit trick. Where has this been my whole life?! Brilliant.
@susan_halla
@susan_halla Жыл бұрын
Just about to build by own miter station, and I’m definitely borrowing your idea for those small drawers on either side that would normally be unused space. I don’t have any patterned plywood, but I’ll be sure to make them pretty nonetheless. Great build!
@kjtemmes
@kjtemmes Жыл бұрын
Baltic birch plywood is now EXTREMELY pricy even in here Finland. Even when our woods are full of birch...
@JeffFine
@JeffFine Жыл бұрын
Very much looking forward to building this and the lathe section, as I have a similar size lathe for making pens. This combination will consolidate my tools and make much more usable space in the garage shop. By the way, I did make your framing sled and it works marvelously! I'm a fearless frame now.
@MichaelAlm
@MichaelAlm Жыл бұрын
That’s awesome!! Plans are going well. They should be available next week 👍
@ronh9384
@ronh9384 Жыл бұрын
Do you have the link to the framing sled?
@JeffFine
@JeffFine Жыл бұрын
@@ronh9384 here it is. kzbin.info/www/bejne/g6OToWV6gbWHqtU The plans are only $5 and we’ll worth it. This sled works fantastically.
@jorgennorrman4023
@jorgennorrman4023 Жыл бұрын
Genuine and quality work, you tcoud build kitchen modules. Those that are available is mostly made by really low quality materials, like sawdust and glue. And if you can make a deal with a housbuilder, then there are good money to make. Fitted build kitchens are a good business, and people are paying good money for a counter topp made of a unique piece of wood.
@corygillies9039
@corygillies9039 10 ай бұрын
Purchased these plans a few weeks ago! I am in the middle of the build now. Michael, what shop vac are you using for this project?
@BentusiProgenitors
@BentusiProgenitors Жыл бұрын
Im going to copy your method and redo my main wall as well. Thanks for the direction.
@EricAlbert
@EricAlbert Жыл бұрын
Fantastic build! The beauty shots are the whole reason I bought the plans, which are equally excellent!
@MichaelAlm
@MichaelAlm Жыл бұрын
Thank you!! 🙌
Best way to store a LATHE?
30:15
Michael Alm (ALM FAB)
Рет қаралды 183 М.
The Miter Saw Station Everyone is Copying!
31:53
Scott Walsh
Рет қаралды 782 М.
бабл ти гель для душа // Eva mash
01:00
EVA mash
Рет қаралды 5 МЛН
小蚂蚁会选到什么呢!#火影忍者 #佐助 #家庭
00:47
火影忍者一家
Рет қаралды 127 МЛН
How I Brought My Old House’s Moldings Back to Life in One Week!
36:26
Michael Alm (ALM FAB)
Рет қаралды 13 М.
I don't get why people think drawers are hard
20:04
MWA Woodworks
Рет қаралды 404 М.
Building a Tiny Office Pod Under My Stairs
51:47
Man Made
Рет қаралды 7 МЛН
Table Saw + Miter Saw WORKBENCH Like No Other
25:31
VanIsle Studio
Рет қаралды 314 М.
Ingenious Construction Workers That Are at Another Level
33:17
#Mind Warehouse
Рет қаралды 89 М.
I built the perfect miter saw solution.
21:38
Lincoln St. Woodworks
Рет қаралды 614 М.
Worlds Nicest Table Saw Sled || Ultimate Table Saw Upgrade
33:30
Bourbon Moth Woodworking
Рет қаралды 935 М.
Miter Saw Station
28:23
Mike Farrington
Рет қаралды 761 М.
I Build 3 Cutting Boards - 5 Min vs. 5 Hour vs. 5 Day
34:14
John Malecki
Рет қаралды 2,4 МЛН
бабл ти гель для душа // Eva mash
01:00
EVA mash
Рет қаралды 5 МЛН