A tip for cutting the bevels.....place your straightedge about 1/4 inch away from the fold and use it to guide the top end of your blade....perfect bevels every time.
@trevor52902 жыл бұрын
This is the best, most informative wing build video that I have seen yet. Thanks for taking the time to post.
@HB_Aircraft2 жыл бұрын
Glad you enjoyed it!
@rodchurchill557610 ай бұрын
I've been watching videos or few hours on how to do this . Yours is hands down the best . I love the one piece idea . The wet paper first is one some talked of hearing about but didn't do . The only thing I question is the fact you didn't appear to match the panel halves for length . I will being using this method for my wings .
@NIRAJPATELV4 ай бұрын
Excellent help Thanks so much love your video Can u pls tell me what make is your exacto knife I like it a lot Cheers 👍👍
@HB_Aircraft4 ай бұрын
K26 Fit Grip Knife by Excel Blades: excelblades.com/products/fitgrip-knife
@fuzzysphere Жыл бұрын
Thank you for a truly clear and useful video. In your opinion, would this technique work for a much thicker airfoil, say with thickness 30% of the chord?
@Videogame95595 ай бұрын
The is a very good video how to make wing thanks great job
@pjryan62262 жыл бұрын
Good man.Im just starting to build myself and this tuition is perfect for me.Keep up the great work and I will get you loads of subs.
@jackjuhasz5332 жыл бұрын
Just what i was looking for ! Thanks
@donaldverhaeghe960311 ай бұрын
Do you have recommendations for cg. and control throws?
@HB_Aircraft11 ай бұрын
CG about 1 inch from the leading edge. Elevator throws of about 20 degrees. Aileron throws of about 35 degrees. Use reduced throws for the first flight then increase them to your preferred level of responsiveness once the plane is trimmed.
@nathangrahl99392 жыл бұрын
If you are going to hotwire cut a solid foam wing cores, what airfoil matches the saddle on the fuselage?
@HB_Aircraft2 жыл бұрын
E168 with a chord of 178mm and 100% thickness. This results in an airfoil that can be cut from a 1" thick foam blank. See: airfoiltools.com/plotter/index?airfoil=e168-il
@TheWingnut58 Жыл бұрын
Using a fully semetrical airfoil, draw a line from the center of the leading edge to the center of the trailing edge along the end of the wing....the bottom half is the shape of the wing saddle.
@cl18t4 ай бұрын
How my aileron reflex does this need?
@HB_Aircraft4 ай бұрын
I don't use any reflex. Unlike a flat bottom wing a symmetrical wing has very little downward pitching movement that needs to be balanced.
@Tonynux Жыл бұрын
is the wing 30 inches long?
@HB_Aircraft Жыл бұрын
Yes the wing shown in this video is a 30 inch wing.
@Magic-hubi Жыл бұрын
Thanks
@Lakshmidevi-ib3jr2 жыл бұрын
what material is used ?
@HB_Aircraft2 жыл бұрын
Foam board, it is foam with a layer of paper on each side. See: store.flitetest.com/flite-test-water-resistant-foam-board-by-adams-25-pack/
@TheWingnut58 Жыл бұрын
The foam board from "Dollar Tree" works great too...
@ricardotrujillo744410 ай бұрын
I assume you mean elevons, not "elverons" right?
@ELIAS-og5vf Жыл бұрын
Hello sir where can buy this bord and what is name plz
@HB_Aircraft Жыл бұрын
You can buy the foam board from the FliteTest store: store.flitetest.com/flite-test-maker-foam-board-by-adams-20-pack/