BUILDING A YAMAHA YFZ450r FROM THE GROUND UP - HOUSER XC A ARMS INSTALL

[@jeffreyginn9643]

Glad to see you’re finally building the second cleanest yfz😉

[@ononewheel7]

Ya my first blacked out one is still hard to beat 🤣🤣🤣

[@jeffreyginn9643]

@@ononewheel7 I hate you😂😂😂

[@shaunbarber2746]

Looking good, keep em coming......

[@ononewheel7]

Thanks man

[@dustinrichards8401]

Did you put nylon nuts on the ball joints to replace the castle nuts cause my ball joints don’t have the hole for a cotter pin and was told I could reuse the castle nut with some blue loctite but would feel more comfortable with a nylon nut

[@ononewheel7]

I did so my two upper ball joints came with the nylon nuts so i just grabbed some for the lower ball joints.

[@dustinrichards8401]

@@ononewheel7 ok thank you, long shot but would you happen to know what thread pitch the nuts would be

[@ononewheel7]

I don’t sorry i think if i remember correctly its not metric i just brought it w me to the hardware store and matched it up.

[@dustinrichards8401]

@@ononewheel7 ok, thank you again!

[@dustinrichards8401]

For the houser tie rods do you have to reuse the jam nuts off the stock tie rods for the tie rod ends?

[@ononewheel7]

Yes

[@dustinrichards8401]

@@ononewheel7 ok, mine are pretty stuck on the stock ones so would you happen to know the thread pitch of the nuts

[@ononewheel7]

Not sure you can order new ones from rockymountain

[@probuiltshop]

Just installed houser mx a-arms, stock spindles, what castor setting you recommend to start with on the slicast?

[@ononewheel7]

Nice man. I run my setup at -3 for the caster settings but that is recommended for xc. Not sure what mx is it may be more towards center or positive caster.

[@bigl2452]

2020YFZ450rse...throttle cable recently became super slack from the box on the right side of the hand grips. How do I tighten this back up ?

[@bigl2452]

Do you have a video on this

[@ononewheel7]

There is an adjustment at the throttle body and at the lever check both and adjust as needed.

[@wittracing72davidwitt74]

My son just boke his OEM Subframe . I put a new OEM one on . Have you every run A Subframe Support ? I was looking a Force Racing Subframe Support

[@ononewheel7]

In 2020 i ran the xcel subframe it was awesome they stopped making them. LSR makes one but I’m not fond of the design and walsh makes one that is super expensive i have seen the braces it sure wont hurt.

[@wittracing72davidwitt74]

@@ononewheel7 Thanks for the info

[@ononewheel7]

Anytime man

[@redrockracing4571]

Hey ononewheel7 do you have any knowledge of the Teixeira Tech A-arms? I like the ground clearance.

[@ononewheel7]

I have some on my can am. Just uppers but they are very nice and beefy i have always heard good thing on his products.

[@redrockracing4571]

@@ononewheel7 Thanks man I’m build up my 22 YFZ in XC

[@ononewheel7]

@@redrockracing4571 nice anytime

[@redrockracing4571]

@@ononewheel7 You use LTR Geometry Housers right? Have you noticed any difference from Yamahas though?

[@ononewheel7]

What kind of difference?

[@ОктайМехмедов]

👏👏👏👍👍

[@bigl2452]

Hello sir,I've been informed that my 2020 YFZ450rse issue was not the throttle cable it's the spring inside the throttle body. My issue is, I'm told that I can't replace the spring, I'm told I must replace the entire throttle body. Is this true?

[@ononewheel7]

You can absolutely replace the throttle body spring. Who ever is telling you this is trying to screw you. Its super easy to replace.

[@bigl2452]

Just so I'm clear, we are talking about the throttle body near the air intake.. not the throttle button on the handle bars.. correct..( sorry for the crazy questions, I'm not as knowledgeable as you, I like to be totally clear)

[@ononewheel7]

Yup you can change that yourself its easy.

[@derekhaynes4251]

What subframe are you going to put on it?

[@ononewheel7]

Oem subframe

[@justride9199]

How’d you learn how to do all this ??

[@kylebeach2316]

It's not hard at all do if you don't know how to do things just watch a KZbin video on what you want

[@ononewheel7]

Learned by just doing it grab a manual for any quad and its all in there.

[@seanclayton309]

Hey man are you from PA? I would love to get a ride in sometime

[@ononewheel7]

Rhode island.

[@seanclayton309]

@@ononewheel7 if you are ever doing a subscriber ride let me know! I would for sure make the trip up there. Or if you are ever in eastern PA let me know I have some great spots in coal county

[@xclife211]

How did you hurt yourself is that why you haven't done nyoa

[@ononewheel7]

I made the decision not to run for points this year before the season started i had planned to race a couple NYOA’s i went to greek peak and got hurt riding downhill on Saturday 😩

[@xclife211]

@@ononewheel7 bummer about the fall hope all goes well next year I've been having electronics issues this year and chasing electrical issues is horrible

[@ononewheel7]

Efi machines can be a nightmare thats for sure. What is your issue?

[@xclife211]

@@ononewheel7 I had a grounded short from a rubbed wire and now I'm waiting on a new tps to come in so hopefully I can get to twisted fence lol

[@ononewheel7]

@@xclife211 bummer man hope you get her fixd up in time 🙏