Part two of three parts showing the building of a crab trap for use on the coast of Texas. Raw Video.
Пікірлер: 54
@CraigFos11 жыл бұрын
If you are referring to the upper chamber, the crabs will try to escape by going up. Once they get in the upper chamber, it is harder for them to find there way back down to the lower chamber and then out the funnels. Crabs will eventually escape out of the tunnels. Double chamber traps work much better than single chamber traps. I have used single chamber traps in shallow water and you need to check them more often.
@CraigFos11 жыл бұрын
Cut out the opening for the bait holder and attach the cover on one side using loose fitting hog rings. Insert a length of bungie chord about two inches down from the hinged side of the door and feed it through the center of the cover. Stretch the chord and secure it together with two hog rings. Feed it through the opening so that the hog rings are inside the trap.
@CraigFos11 жыл бұрын
Start with the oldest post and work your way up. The supplies were purchased at Home Depot, Lowes, and San Leon Marina. The wire for the main body is available at America Fence in this area.
@CraigFos11 жыл бұрын
Bottom of Trap Cut out thirty five meshes (52.5”), flat on both sides. Fold side up at 8 meshes and 11 meshes from the ends. Attach bait holder in the center using hog rings.
@CraigFos11 жыл бұрын
Bait Holder Cut out 24” wire hardware cloth 18” long with a tab on one end. This will make two bait holders and three covers. Cut 9” with a tab off of the top and bottom. Cut the middle into three sections for the covers. Roll one of the 9” tall sections to form the bait holder, bend the tabs to secure. Insert one of the covers onto the top tabbed section and secure.
@CraigFos11 жыл бұрын
Baffle Cut out eighteen meshes (27”), tabbed on both sides. Bend center mesh over the side of a 2X4. Attach baffle to the bottom 5 meshes up from the bottom. Attach the top of the bait box to the baffle using hog rings. Cut the opening in the baffle, starting one mesh in and leaving tabs on all sides. Cut 4 mesh in cutting on opposite sides of the center wire. Fold the tabs up. Repeat on opposite side.
@CraigFos11 жыл бұрын
It is cheaper to make him and buy them, but if you are just in it to save money the time is not worth the savings. I enjoyed making the traps and modifying them in different ways to try to improve my catch.
@CraigFos11 жыл бұрын
Funnels Cut out five meshes leaving a tab. Fold in half and secure the open side by folding. Fold the two flat end corners to form a funnel. Cut an opening one mesh up and five meshes in from both sides. Attach funnel using tabs. Repeat on all four sides.
@grantfoster90995 жыл бұрын
Bend the corners on the two pannels but not on the side where the door goes on it makes the trap easier to build 😊
@CraigFos11 жыл бұрын
Top of Trap Cut out thirty eight meshes (57”), tabbed on both sides. Attach the tabs to the bottom and use hog rings to secure sides. Make sure the trap is flat and attach the baffle to the sides of the top using hog rings.
@CoquiAudio8 жыл бұрын
thank so much for all parts of the video sir here in Puerto Rico we catch them into the river close by Quajataca tunnel in Quebradillas town close to "Isabela town too" :)
@CraigFos11 жыл бұрын
Door Cut out four meshes (6”), flat on both sides, set aside until top is attached.
@CraigFos11 жыл бұрын
Escape Rings Install two escape rings in each chamber by cutting out the center of four meshes and using the tabs to secure the rings. Attach the float with enough line for the area you plan to crab. Bait and catch some crabs.
@aroundtheclockservicesatc32173 жыл бұрын
Hello you seem to know a bit about crab pots where is the best places to get the West wiring material to make crab pots
@CraigFos3 жыл бұрын
@@aroundtheclockservicesatc3217 I get my wire from San Leon Marine Supply at 2100 Avenue J, San Leon, TX 77539. Phone: (281) 339-1016.
@msladebeatz2 жыл бұрын
@@CraigFos Awesome video!! What gauge wire do you use?
@materialsky31311 жыл бұрын
Thanks!
@CraigFos11 жыл бұрын
Attach the door to the opening using three electrical straps. The center strap should be attached in a figure 8 style to keep the door from sliding side to side. Fold the top over the top edge of the trap. Insert the plastic latch on a length of bungie chord and attach it in two places to the door. Tie a bio-degradable string to the top of the trap to hook the latch in.
@rongrey74494 жыл бұрын
Craig Fos was there a part 2 to this video?
@four-x-trading56063 жыл бұрын
can you put measurements for each item that goes into the trap?
@jackiecary2911 жыл бұрын
Hey great video. I grew up on tybee ga and I learned the waters grom my parents. We do it all oyster crabs clams etc. I always wantef to learm how to make crab traps of my own. I just learnef how from yor video. One question where can I get the measurement to do it and the hardware. One again awsome video
@ericalexander80276 жыл бұрын
do you have a set of plans you used?
@rongrey74494 жыл бұрын
After you hog clipped the bait holder, did you cut the opposite side to have the opening?
@DebbieTomkoSUNSHINE2 жыл бұрын
Can poultry wire be used?
@rongrey74494 жыл бұрын
I was sea sick trying to keep my eyes focused, what was the final results? Why was that inside wire placed over the bait box? How many entrances Did you put? Any escape rings? Degradable panel or mesh? I live in Florida an these trap spec’s seem unlimited.
@FishingPhoFun4 жыл бұрын
What size hog rings are those?
@robjennings95655 жыл бұрын
All that zooming in and out has made me feel sea sick 🤕
@knowlifenation85453 жыл бұрын
Where do you get that mesh from in Texas?
@connormoore23107 жыл бұрын
What is the height and length of the wire
@MrWilliamyang6 жыл бұрын
What size hog rings?
@elmatt18718 жыл бұрын
hi what wire mesh u using? what is it called?
@grantfoster90995 жыл бұрын
Riverdale Wire
@MrDenali5437 жыл бұрын
What size mesh is the main wire? Also what is the width of the roll of main wire?
@grantfoster90994 жыл бұрын
16 gauge Riverdale Wire
@btgame18363 жыл бұрын
What size a the hole you the phorts
@mikermason10 жыл бұрын
where did you get your supplies and directions
@CraigFos10 жыл бұрын
I got my supplies for the funnels at Home Depot and most of the rest of the supplies at San Leon Marine Supply, I did find that you can get the main wire cheaper at Houston Fence and Supply in Galveston. As for directions, I just modified different designs to meet my needs.
@mikeyxmr7 жыл бұрын
what size is the red mesh wire?
@CraigFos7 жыл бұрын
Mark Morvant, one and a half inch.
@williamhzerbejr1289 ай бұрын
What size chicken wire for funnels and bait box
@CraigFos9 ай бұрын
I use GARDEN CRAFT 25-ft x 2-ft-Gauge Green PVC Coated Steel Chicken Wire Rolled Fencing with Mesh Size 1-in that I purchased at Lowes.
@brianthomas7520 Жыл бұрын
Do you have any pics with crabs in
@CraigFos Жыл бұрын
Here is a photo of crabs in 4 of the traps: drive.google.com/file/d/1D_djM1qgqfpqDhTUoOBEu270oyExZ160/view?usp=sharing
@guillermosilva26714 жыл бұрын
At what store do I buy the wire roll?
@CraigFos4 жыл бұрын
I got it from San Leon Marine near Texas City, Tx.
@hieunguyen-gh9pq10 жыл бұрын
what the name of the plier do you use thank
@CraigFos10 жыл бұрын
Hog nose ring pliers
@hieunguyen-gh9pq10 жыл бұрын
thank you verymuch
@codykiller76058 жыл бұрын
+Craig Fos thanks for your help and love your video
@jepthalong199811 жыл бұрын
where did u get the directions you are using to build your traps?
@materialsky31311 жыл бұрын
I still don't quite understand the point for that part 8:46 . Is it to put some crabs up there for more space at the bottom until you retrieve the trap?