Honda COP Distributor Conversion

[@RideRevival_Outdoor]

from the time i found your coil on plug setup i had been asking myself if this was possible and how to do it. Days later, BAM Burton Racing video on it. Thanks!

[@revelopez112]

I just ordered an ecu from you guys! If I'm happy with it I'll definitely be sending it back for this kit install. Looks awesome

[@richd2744]

Any recommendations on aftermarket Distributors that work well with this? My OEM one went out, went to a Duralast one which works fine but it doesn't fit the block off plates. Apparently some have issues. I tried another brand and couldn't even get Spark.

[@situatedillness]

Ok so question, obd2b does not need the rpm wire, but what if i have an obd2 to obd1 conversion? Do I now have to use that or is is it still ok to not use it?

[@BurtonRacing]

For full instructions please email [e-mail]

[@jgriffin566]

You ever find the answer

[@situatedillness]

@@jgriffin566 nope

[@mfzb0912]

​@@situatedillnessupdate?

[@yeetplays3421]

NEED HELP HERE!🤚🏼🤚🏼🤚🏼🤚🏼🤚🏼I have the Burton racing copk on a obd2 distributor and I have and issue where my RPM tach stop working. In the beginning it will come and go once in a while and then it stop working completely. So I have change clusters to see if it was that but it does it with whatever cluster I switch too, RPM tach won’t work. What could it be?

[@allentownrep]

Im confused. Dont we need the 2pin plug for the COP kit to work? In the COP video it shows how you de-pin the 2 wire plug to get the power which is black and yellow wire and the RPM wire which is the solid blue wire signals. Can you guys clear that up?

[@And1dc2]

Yea this needs to be cleared up it doesn't make any sense

[@allentownrep]

@@And1dc2 I emailed them about it. You're getting the power and RPM signal from the actual harness side. What he is removing is from the distributor side.

[@And1dc2]

Yea I just figured that out a little bit after watching the video haha it's actually pretty cool the way it all works

[@cvseth22]

@andid95 can someone explain it to me ,I'm quite confused as well and I'm trying to do mine's now

[@otithehondahorder234]

looks like it will work with obd2B? small plug is the same but no rpm wire

[@JustThatOneMexican]

I like the step by step, I recently did mine and had an issue with the roll pin that keeps the hall effect in place and it actually flew off causing a no spark symptom, ended up using a spacer and cotter pin just to ensure it stays in place, have you guys ever seen something like this happen?

[@lewzero]

It's low on the list of "will buy" parts, but I absolutely need this. Heli-coil to fix where the exhaust manifold stud got drilled out of the head just a _little_ too deep......

[@johnsmithnonya46]

How can you cut the blue wire you called it the speed reference, and still get RPM??

[@BurtonRacing]

Please email [e-mail]

[@Racecarhuey]

Another “how to” vid using an obd2b distributor would be greatly appreciated. I purchased my br cop system about a year but all supporting info is for obd1 systems.

[@BurtonRacing]

For all specific questions you can contact us directly at [e-mail] the concept is the exact same, some specific applications may vary however we provide all the information needed to navigate an install on all factory style applications.

[@nicolasquesada7060]

Hello My Friend, Friend, could you help me with the electrical diagram of how to do to be able to Assemble the system of independent Coils for My car

[@freddieximenez7138]

I have a hondata s300 on a 92 acura integra b20v gsr distributor how much is this kid cost.?

[@BurtonRacing]

www.burton-racing.com

[@minni1094]

Does the ICM have to be removed for the COP to work correctly? I removed the coil but not ICM.

[@BurtonRacing]

Not necessary for the COP to work.

[@ElleEnd]

Wish you guys were in Australia :c

[@rcred80]

Do you have to do anything to the ecu

[@BurtonRacing]

Please email [e-mail]

[@georgeowen3506]

How do you do this to nissan ka24de distributors

[@tylercooper3842]

Will it work on a broken dis?

[@BurtonRacing]

Depends whats broken. Many components are housed inside.

[@duanedonaldson2262]

If the body case is not broken, all you need is another junk dizzy to cannibalize parts from, the internals are the same if the clocking on the outside is different just be sure its the same type.

[@LuisRodriguez-io6yq]

Where did you put the two wire that come with coil plug

[@BurtonRacing]

That connects to the engine harness. Please watch our COP video for step by step.

[@JEKFROOT]

So,basically for this to work just connect the ICM wire (yellow/green) & the speedo wire (blue) on the engine harness. Correct?

[@wernwerks819]

On the engine harness you will connect the wires of the distributors 2 pin plug to the COP harness. On mine I depinned the distributors old 2 pin plug and repinned the Burton harness into it. The blue wire is the RPM signal to the cluster, the other is your switched ignition power to power the coils.

[@TwistedAutoGarage]

What about obd2b i have a 98 crv

[@steventru9878]

What is needed to do this on a obd2a

[@BurtonRacing]

An obd1 ecu conversion and the purchase/install of the cop system from www.burton-racing.com

[@alexm4890]

I don't get how u attached coil?

[@duanedonaldson2262]

This video only shows a portion of the mod

[@537R4HC]

i have a ECU that needs a service to work with obd2b

[@duanedonaldson2262]

There are plenty of Honda Forums to help you with all your needs

[@537R4HC]

WTB> OBD2b GSR Distributor serious

[@maideantrico3678]

can obd0 do this?

[@BurtonRacing]

With an obd1 ecu conversion

[@maideantrico3678]

@@BurtonRacing how much?

[@BurtonRacing]

@@maideantrico3678 www.burton-racing.com