Butcher Block Top Finishing

[@Johnny-fb1hm]

I used waterlox to seal my butcher block top - followed these directions - came out great. Will definitely use this same technique again. Just seems you gotta patient. Been about 6-7 weeks, and has more than a hint of the smell, so hasn’t completely dried. I don’t handle food directly on it, but we’ll see after 3 months.

[@MADKILL4]

Update?

[@Johnny-fb1hm]

Been well over a year - my stained butcher block has held up great, the hint of chemical scent went away after a couple months, still looks great now and it gets a lot of use. I followed almost exactly how the video showed it applied.

[@SeymourKitty]

That's a mighty fine piece of wood you got there sir.

[@mtatman22]

Thank you sir, one of the better videos on this subject.

[@debbiec2663]

Very helpful video. I am new to finishing wood. I appreciate you sharing your process and knowledge.

[@susanbernaix6909]

You just made my life easier.

[@huntwoodcabinetoutlet1627]

Glad to hear!

[@williamyenkevich2466]

A really nice piece of wood finished well!

[@artpimentel5244]

I bought this for my friend for his birthday as we just moved into a new house and he finally has room for a workshop. The bench was very easy to set up kzbin.infoUgkxyFZUPFEey-PuqsPMxqaykBhgA1LWxFHh They center support is a little difficult to snap in and out of place at first but at least then we know the bench is secure. It was a pleasant surprise when we saw it came with clamps. I apparently missed that in the description. My friend loves the versatility of the bench. Great starter bench for his workshop and easily transportable all over our property. I wish the bench was a little taller but the other features of the bench more than make up for that.

[@Jason_from_cal]

Good job on the video man! Thanks for the info!

[@OtterLakeFlutes]

I thought about Waterlox original or satin but did not see anywhere on the ad it was food contact safe (my use is for wooden flutes with mouthpieces, to a rather hyper-green-safe-conscious crowd (some of them won't even touch their lips to mineral oil because it's petroleum, meanwhile I drink a tablespoon to loosen up the ol' lower belly). I have some 50/50 tung oil / citrus solvent that I guess doesn't seem to take too terribly long to dry, and I sort of post-finish with Odie's Oil (in part for the smell) but something appliewd after the 50/50% Tung/D-limondene and before Odie's would be something that doesn't take forever to dry but puts a little sheen on. I've heard different areas of cut or grain can absorb Watco Butcher Block Oil to look uneven or spotty, but I thought maybe the penetrating pre-treatment of the 50/50 might mitigate that. I also can NOT find out what is in the Watco. But now you're indicating Waterlox is food contact safe, so maybe it would be good. Oh wait I see you're using Waterlox the way I'm using 50/50 as a penetrating 1st two coats, anyway, maybe tomato tomahto. Awesome paper hint! I'm to assume the tung is just pure tung...? Hmm... looks way runnier... looks the exact same as what you said was Waterlox... the popup sign was the only thing indicating the switch from Waterlox to tung and you saying "second coat" and all seems like you never switched products... I did benefit here...

[@huntwoodcabinetoutlet1627]

Boy, that's a good one. Not sure that putting Waterlox on a mouthpiece is good. I recommend to contact the company and ask them.

[@cshan7680]

Wonderful video. Thanks.

[@huntwoodcabinetoutlet1627]

Thanks for your nice comment. We are glad you liked it!

[@deborahgregory-fink5464]

good information. very clear.

[@wolffelipe]

That was really good!

[@AdamTheCarpenter]

Ever considered Rubio Monocoat as a finish instead? Seems to be super quick and easy and durable as all get out. Has been used in the flooring industry for decades.

[@huntwoodcabinetoutlet1627]

No, this is what we use.

[@martingo2680]

I did hear uou mentioned the name of the product but can you please type it in the comment box again? Just be sure..

[@huntwoodcabinetoutlet1627]

Waterlox Original is the sealer finish and comes in a metal can.

[@debcecotti8273]

Thanks

[@UbiDoobyBanooby]

The text said Tung Oil but the guy said Linseed Oil. I'm guessing you meant Tungseed since that's the one you would use for a kitchen application, being good safe, water resistant and dries hard.

[@huntwoodcabinetoutlet1627]

We use "Waterlox".

[@truthinadvertising2702]

@Mr Sunshines Tung oil comes from Tung fruit from a tree in China and Linseed oil is from flax seeds. Neither is toxic, unlike mineral oil which is also called liquid petroleum-derived from crude oil.

[@NobleNobbler]

I lol'd after seeing your name was Mr Sunshines

[@brianpayers]

@@huntwoodcabinetoutlet1627 What kind of waterlox? There seems to be many different options... can you perhaps send a link to the exact version you use?

[@huntwoodcabinetoutlet1627]

​@@brianpayers We use Waterlox Original, Satin/Medium Sheen (which gives it a semi glossy finish). Here is the link: www.waterlox.com/original

[@ritual301]

Cool little video. Thank you

[@leifjohnsenvt]

This is a great tutorial, thank you so much. I am curios, should you be wearing a mask?

[@huntwoodcabinetoutlet1627]

If you are in a well ventilated area, then no, you do not need to wear a mask.

[@leifjohnsenvt]

@@huntwoodcabinetoutlet1627 Thanks for the reply. I am very worried about particles and am very new so its nice to hear I can relax a bit in a well vented area. Thanks again.

[@djneville2000]

I just completed a garage workbench. I want to finish the top with this type of oil. Living in Michigan the temperature in the garage is about 40 degrees right now. Will this affect the oil drying and should I wait until higher temps? Thanks

[@huntwoodcabinetoutlet1627]

Yes, it will affect the dry time. It should be around 60 degrees. You still can oil but will take longer to dry. Anything below that, I wouldn't oil till it warms up.

[@phillamoore157]

I'm getting ready to do that exact project. Mine's a large slab connecting cabinetry on each end (and underneath). Were you happy with how yours turned out?

[@captaindrywall]

I am ready for the oil.. I came here to see how to clean every spec of sawdust. If he just put oil on the countertop without removing all dust he, and you are screwed. do not skip the part were you get all the dust off. I don't mean just vacuum or wipe down.

[@kalef1234]

mmmmm that's some nice wood right there

[@KityKati]

Did u wet it prior to sanding? Someone told me to keep rubbing water on it for a few days top and bottom and that will help it swell to close very slight gaps. Had it made by a company for island top 3ft by 5ft, needs sanding and oiled. Do i have to oil the bottom with both oils or only do the bottom with linseed? Also, would you suggest a polyurethane finish instead?

[@huntwoodcabinetoutlet1627]

I have never heard of that. If you put water on your top the oil will not penetrate the wood deep enough to protect it. I put 2 coats of oil on the bottom, only one kind though. I would not use 2 different kinds of oils. As far as the polyurethane, you could, but you don't want to cut on it. Use a cutting board that has been oiled.

[@KityKati]

Not sanded yet. Stopped putting water on it for now bcuz i was waiting for your answer. So u only use Waterlox Linseed oil or tung is good too? Do u also do this monthly?

[@huntwoodcabinetoutlet1627]

No, you don't need to Waterlox it but once a year. Put first coat on, sand with 180 grit, second coat sand with 500 grit will make for a smooth surface for your last coat. When dry paper sand and you're done.

[@MiniMoto2424]

Great video thank you so much!

[@lollysmomgerl8994]

if a butcher block gel stain & satin top coat are used. Should the Tung Oil still be used? If so, should Tung oil be used before application of the gel stain & satin top coat? Thanks for the video - the countertop looks nice!

[@huntwoodcabinetoutlet1627]

No, you don't want to use both, rather use one or the other. I hope that there is not going to be food prep on the top. Tung oil is used on tops that will be used for food prep. Stain and top-coat will contaminate the food.

[@lollysmomgerl8994]

thank you for letting me know that - guess I will stick with the tung oil. @@huntwoodcabinetoutlet1627

[@ScottKorin]

At 3:24, the graphic says tung oil, but then the gentleman said he was using WaterLox, which is linseed oil based. So, which is it?

[@huntwoodcabinetoutlet1627]

Waterlox is a tung oil based wood sealer/finish.

[@phillamoore157]

Considering using this product on a workbench top.... Can anyone give me a reason this product wouldn't work, or if there's a better product out there for that purpose?

[@lindasuevandergrift8850]

We're getting butcher block countertops in our kitchen. We're thinking of using Danish oil. Is that the same as tung oil?

[@huntwoodcabinetoutlet1627]

No, it is not. Danish oil is a mix of oils and varnishes. Varnish is toxic and should not be put on countertops that will have food prepared on them. It would be best to contact the product maker, that you are thinking of buying, and asks them.

[@imckdonnelly]

What kind of router bit did you use? 3/8" round over? How deep did you go to get such a nice roundover, mine always come out a little "sharp" almost

[@huntwoodcabinetoutlet1627]

Yes, 3/8" Round Over. Set the bit so that you take off the edge but not too deep that you put a groove or lip on the front and/or the top.

[@gasousman]

Hi. Thanks for these great wood working videos. I mistakenly used Polyacrylic instead of water based polyurethane (Lowe's had it sitting right next to their oil based polyurethane). Now, months later, the paper from boxes, like cereal or popcorn, sticks to the polyacrylic. I then have to scrape the paper free. How can I fix this?

[@huntwoodcabinetoutlet1627]

That has not been my experience with Polyacrylic, so it may be defective. You could call the company and see what they say.

[@avamaria8447]

My neighbor cut down a pine tree with super large branches. I would love to make some circular butcher blocks. Is the pine appropriate for this and do I need to let it dry completely? Thanks for this video, hope we hear back.

[@huntwoodcabinetoutlet1627]

Yes, you can use pine, and yes it needs to be dry.

[@avamaria8447]

@@huntwoodcabinetoutlet1627 thank you so very much.

[@huntwoodcabinetoutlet1627]

​@@avamaria8447 ​ By the way... Pine is a very soft wood and will damage very easily…the oiling process is not intended to protect the wood from that standpoint but the oil will help protect the wood as far as sealing it up. Using pine as a butcher block, in my opinion, is not a good idea unless it's fully understood that it will get a lot of damage to it from cutting on it if it is intended for an actual butcher block.

[@avamaria8447]

@@huntwoodcabinetoutlet1627 ok, thanks for telling me. I'll still use it, but now I know what to expect.

[@shainmiah6122]

I have a dinning table made of pine which has been hard waxed. Unfortunately even though it looks great, it leave marks and scratches. What can I do to seal it and make it more scratch resistant

[@huntwoodcabinetoutlet1627]

You'll probably need to do some research on finishing products that actually harden and reach out to a true furniture company that builds pine furniture.

[@LiveLaughSmile]

What do you suggest is more beautiful finish? Oil base or water base?

[@huntwoodcabinetoutlet1627]

That would be up to personal taste. Try both on a small piece of wood. That way you can see what looks best to you. Personally, I like oil, which has a better sheen to it.

[@LiveLaughSmile]

Well, I did both sides, using different finishes to see what I like most. One water based protection and the other side butcher oil. So the butcher oil I used I loved it. The water based l didn’t like . Thank you! I did this to the wet bar on the basement. It turned so beautiful!

[@huntwoodcabinetoutlet1627]

@@LiveLaughSmile Good to hear, I'm glad it turned out well for you!

[@LiveLaughSmile]

@@huntwoodcabinetoutlet1627 thank you!

[@kenchambers7604]

Thanks! Good video. What kind of maintenance does a counter top finished this way need over time?

[@huntwoodcabinetoutlet1627]

It depends on the amount of use and how bad it gets dinged up. If kept in fairly good shape, you can get away with a light sanding and re-oiling. Otherwise, you will likely need to re-sand much deeper. Remember that it is all in steps: as sanding takes place, step down the level of paper coarseness from roughly 150 grit to 180 to 220, etc. The oiling is in layers as well. The desired look is all in the success of the prep work. Other tips: If you have a small spot, you shouldn’t sand too much or you may have to totally re-sand. Also, use a clean rag and go in the direction of the wood grain.

[@rrbb36]

“Background music” should be just that…in the BACKGROUND!

[@LEMUSA77]

😂😂😂

[@transitvandiego]

"don't slop it around... " then he slops it over the side lol

[@clairehood9099]

What grit of sandpaper did you use between the two coats of tung oil?

[@huntwoodcabinetoutlet1627]

Just a sheet of paper, no grit. Depending on how rough the top is, most of the time paper sanding will work, if it is rough use 500 grit. You don't want to stay in one spot, as you need to keep the sander moving.

[@Melenaos]

@@huntwoodcabinetoutlet1627 just a normal sheet of paper, like from printer machine?

[@huntwoodcabinetoutlet1627]

@@Melenaos Yes, exactly.

[@shawoo]

Just to confirm, staining is optional correct? I purchased an unfinished American poplar butcher block. Was planning on just clear coating it. Any concerns with that?

[@huntwoodcabinetoutlet1627]

Correct. The only concern is if it will be used for food prep or not, as other clear coats are toxic. If this is being used for food prep, be sure to use Waterlox as it is not toxic after it dries.

[@shawoo]

BargainHUNT great thank you. Will be using as a laundry folding table , so sounds like I’m ok

[@huntwoodcabinetoutlet1627]

@Mr Sunshines I’ve never heard of that, so I called a technical Rep. at Waterlox, as well as found great info on their website: www.waterlox.com Here’s what I found out: - On their website, it says “Waterlox Original Tung oil finishes are water resistant, stand up to household spills and are non-toxic1 and food-safe when dry. Waterlox Original Tung oil finishes have good heat resistance, can be used around stoves and are unaffected by boiling water and liquids.“ - The Rep. said “Once the Waterlox has cured (dry time typically 24 hours, with good ventilation, low humidity and not cool temperatures), it is not toxic, and it cannot get un-cured. So, once the Waterlox has cured it is food safe”. - The Rep. also said as far as cutting food on a Waterlox wood top, that cutting into the Waterlox breaks the seal for protecting the wood. So if knives are used to cut food on the Waterlox wood countertop and if you want to continue to protect the wood from water/liquid damage, then a food grade oil should be applied every week of use.

[@RittaTT]

hello.. so you don't use beeswax then? I bought a wooden board that I wona turn into a kitchen cutting board.. Thank you

[@huntwoodcabinetoutlet1627]

No, we don't.

[@alexandreash9037]

I put 3 coat of oil on top but I forgot to wipe the extra oil after the third coat, now its all sticky! what should I do?

[@huntwoodcabinetoutlet1627]

How long did you leave it to dry? With not wiping the last coat off, it will take longer to dry.

[@BigSway22]

How long should I wait after my final coat to do a clear top coat? I’m making this a desk and want to preserve the wood

[@huntwoodcabinetoutlet1627]

Depends on the weather. If it's 70° plus then 24 hours. If it's under that then 36 hours.

[@BigSway22]

@@huntwoodcabinetoutlet1627 if I didn’t coat it in clear would I damage the wood using it as a desk?

[@huntwoodcabinetoutlet1627]

@@BigSway22 Over time, it would fade/darken. UV lighting turns the wood darker.

[@Hollymarie212]

What brand or kind of Tung oil is used here?

[@huntwoodcabinetoutlet1627]

It is Waterlox.

[@avarmauk]

I’ve used mineral oil on my butcher block. But over time it seems to fade. Will using tung oil be longer lasting?

[@huntwoodcabinetoutlet1627]

No, overtime anything that is in the sun will fade. Doesn't matter what it is. UV light works just like the sunlight. Will make things fade over time.

[@071946]

Mineral o oil and bees wax 4 to 1

[@maniac1972]

So is it one coat on the back then two on top with a sanding between coats.

[@huntwoodcabinetoutlet1627]

No. 2 coats on the bottom and 3 coats on the top. Before the last coat, you'll want to lightly paper sand with regular paper.

[@danedauphin2244]

Help, please!! i used a stain. Too red. I wan't 'blonde' what do i do?

[@huntwoodcabinetoutlet1627]

You could try sanding it (180 Grit). Maybe it will work, depending on how deep the red color went into the wood.

[@earldavis2822]

This is probably a very good demonstration on finishing a butcher block but the music is totally annoying. Being a little on the hard of hearing side I could hardly make out what was being said. I didn't watch the whole video but would have without the music.

[@stevephillips8192]

I love music, but could you imagine school classrooms having soft background music playing all the time!!! Pick a time when you’re not teaching (talking) if you want to play music. Ok I’m getting down off my box, you can start the music 🎷🎻🪗🎹🎼🎺

[@truderenken3248]

Background music makes it very hard to hear the instructions

[@sandrameyer131]

Does the circular sander leave marks? We have the kitchen countertops in need of a good sanding as they are 30 years old.

[@huntwoodcabinetoutlet1627]

If you use 100 grit sandpaper, then yes it can leave marks. It would be better to use 180 or 220 grit. Due to the age, of course you won't be able to spot sand (as it won't look right) but rather will need to evenly sand the entire surface, so it all looks the same. Hope all goes well!

[@alhambra119]

Good information, but the music is not a good idea.

[@cookiedavis180]

Do you sell these? That is beautiful

[@huntwoodcabinetoutlet1627]

Yes, we sell Butcher Block Tops. If you'd like to inquire more, you can call or email George Dunbar in our customer service department and he can best direct you according to what you are looking for. George's phone # is: 1(800) 873-7350 _ extension: 1108 or email him at: [e-mail]

[@mikefarinella5268]

Dust mask?

[@mikefarinella5268]

Golly, I was just asking a helpful question. BTW, FUCK YOU!

[@stefanosvolicas7008]

can i strait polyurethane a butcher block

[@huntwoodcabinetoutlet1627]

Yes, you can. I would advise to put at least 2 coats on your top for better protection.

[@alejandropatino6656]

What kind of wood was this board made of?

[@huntwoodcabinetoutlet1627]

Maple, 1.5" thick.

[@lgmnowkondo938]

so the waterlox is the undercoat? I thought it was a final coat sealer...One question though, I sealed my butcherblock counter with waterlox, and the counter that gets sunlight really gets light and brittle fairly quickly compared to the rest of the counter. Is there anything I could do for that?

[@huntwoodcabinetoutlet1627]

I haven’t heard of this happening. The waterlox is the only thing that I put on. From the first to the last. Three coats total. Maybe call the maker of waterlox to find what we could do about this. I would like to know.

[@lgmnowkondo938]

your video says "applying tung oil" final coat....is tung oil waterlox? I thought it was linseed...seems unnecessarily confusing.

[@huntwoodcabinetoutlet1627]

It's not confusing. Yes, Waterlox is one type of tung oil. It's made up of several types of resins, oil, and gum. The TOP 5 are: Tung Oil, Mineral Spirits, Ester Gum, Phenolin Gum, and Olefin Gum.

[@gmkpl]

Is this product also safe for food?

[@huntwoodcabinetoutlet1627]

Yes, it is. Restaurants use it on their tops. But to be safe, don't use it near open flames until it dries.

[@nursebynight14]

How many inches thick should the wood be for countertops

[@huntwoodcabinetoutlet1627]

1 to 3 inches thick is recommended. The thicker the better, for less chance of warping. 1.5 inches is our standard, and we have done tops up to 4 inches. 1 inch is more cost effective (though be sure to secure it down well, to help prevent warping).

[@anonymouspdg6121]

Hi, after sanding, what do you clean the block with to remove any dust particles before coating it again?

[@huntwoodcabinetoutlet1627]

Use an air hose and a dry cloth. If you don't have air, then the cloth will work. After the first coat paper sand (which means that you use a piece of paper to sand the top). Then put the next coat on the paper sand, and then the last coat.

[@rebelhank3936]

Would be a good video if I could hear you, ditch the music

[@pierrex3226]

that is not tung oil. the guy literally says it's linseed oil based.

[@huntwoodcabinetoutlet1627]

Waterlox has many ingredients. The top 5 are, from the most to the least, mineral sprits, specially processed tung oil, ester gum, phenolic resin and linseed oil.

[@IntrepidJordan]

Speak with confidence

[@scottwaynewootton731]

Your background music too loud.

[@eliot5220]

No mask ! Breathing in a lot of dust

[@terrydunaway8652]

Turn the music off ...it ruins the video

[@davidwarner3692]

What would have been a good video was totally ruined by irritating and totally unnecessary background music! I wanted to hear what you were saying - not supermarket music!

[@ritual301]

Mute + Dying Fetus playlist = problem solved.

[@Eloscarrc]

You’re a supermarket

[@minihooperminihooper4467]

Haters gonna hate

[@lynnesummers8]

David Warner you are a miserable human being! The video was great and very helpful

[@joycecampbell6307]

So STOOOOOPID

[@jayweston5981]

The annoying music is an unnecessary distraction,making it difficult and bothersome to listen to the dialogue.It made me skip the video!