Thanks Lars, your videos are invaluable.Just wondering if you have thoughts on video cards, particularly to suet 4k monitors.
@cadcamstuff6 жыл бұрын
Hi Matt Eyles Thank you for watching! I wish I could help. But honestly, I know very little about this kind of stuff. I would recommend that you check out the forum for this kind of stuff. forums.autodesk.com/t5/fusion-360-design-validate/bd-p/124
@darren43926 жыл бұрын
Hi Lars, Thanks for the videos. They are a great help in learning Fusion 360. Sometimes while I'm using Fusion, the view cube in the top right corner stops working, the home icon disappears and the only way I can change the point of view is to use the orbit function. Hitting escape doesn't unfreeze it. The other commands still work and I can still interact with the model, so the software hasn't crashed. Have you seen this? Is there a way to get the view cube working again?
@cadcamstuff6 жыл бұрын
Hi Darren Healey Thank you for watching! Honestly, I have not seen it myself. Check out this article: knowledge.autodesk.com/support/fusion-360/learn-explore/caas/sfdcarticles/sfdcarticles/How-to-optimize-settings-in-Fusion-360-for-performance.html Also, here is the support forum if you need it: forums.autodesk.com/t5/fusion-360-support/bd-p/962 Best, Lars
@wernerberry78006 жыл бұрын
Love when you have the Haas sim on Buddy! Great video!
@cadcamstuff6 жыл бұрын
Thank you Werner Berry :-)
@Flyingjaffacake6 жыл бұрын
Lars, your videos are invaluable: clear, concise and well produced. Thanks again. Have you considered setting up a Patreon page?
@cadcamstuff6 жыл бұрын
Hi David Spencer Thank you for watching! ANd thank you for the kind words! I do work for Autodesk so I am compensated for most of the time I spend on these videos :-)
@Flyingjaffacake6 жыл бұрын
Good to hear. Thanks for the reply, I appreciate it.
@ShriramEmoters6 жыл бұрын
I loved fusion 360
@hydro16metal6 жыл бұрын
Learning fusion ...you've been lots of help.. thinks for the beginner info
@cadcamstuff6 жыл бұрын
You are so very welcome :-) Thank you for watching!
@JulianMakes6 жыл бұрын
Hi Lars, one thing that's annoying is if i make a circle (by giving a diameter), later on i highlight the circle/cylinder etc and it shows as a radius. so mentally i'm allways doubling stuff, i only want to see diameters usually. is there somehitng i can change?
@cadcamstuff6 жыл бұрын
Hi JulianHG Thank you for watching! I just drew a circle and extruded into 3D space. I clicked the edge and it shows as a radius in the lower left...In my opinion, this should be a diameter. I think you might be on to something. I need to look into this and figure out who to talk to. Thank you! Best, Lars
@JulianMakes6 жыл бұрын
brilliant thanks to much!
@billvanca93776 жыл бұрын
Lars, I had a question about the lollipop router bit you used. What is the brand and part no and where can I purchase. Also, very early on videos you or the CNC handbook you referenced a "Bullnose" router bit is talked about. I had searched for such a bit on the internet with not luck. So the same question for make and part number. I have a 1/4" shank limitation. Thanks in advance!
@cadcamstuff6 жыл бұрын
Hi Bill Vanca Thank you for watching! Lollipop is always called undercutting endmill www.harveytool.com/cat/Undercutting-End-Mills/Specialty-Profiles/Browse-Our-Products_192.aspx You will also find Bull-nose as a corner radius endmill. Hope this is helpful. Best, Lars
@douglasdupont70536 жыл бұрын
Lars, I would like to see if you can Deburr undercut with that lollipop tool. We have to deburr cross holes a lot here.
@cadcamstuff6 жыл бұрын
Hi Douglas DuPont Thank you for watching! I would have to look into this, but I think you would have to used the same contour toolpath and just adjust it to one pass. Best, Lars
@herminsularbelaez78594 жыл бұрын
thank Lars really good video.
@babajan41856 жыл бұрын
i want to generate undercut machining on one shoe mold surface can send you my igs file
@cadcamstuff6 жыл бұрын
Hi Hafeez Khan Thank you for watching! I'm having trouble finding the time to help individuals, you might want to try to Fusion forum: forums.autodesk.com/t5/fusion-360-computer-aided/bd-p/2070 Best, Lars
@woodywood19516 жыл бұрын
In fatc, it's only a couple of minutes about undercutting...
@cadcamstuff6 жыл бұрын
Fact!...Hmm, should there have been more examples? Love you feedback