Calibrate steering angle sensor on Chevy truck

[@TheVega2all]

I m very thankful with you my friend I’m am a one of those wanna be and you are an excellent teacher

[@abdiaspablo7130]

The new technology of automotive alignment

[@Khaled-if4xs]

Thank you brother As a mechanic it's very helpful tutorial for us

[@carlosnovoa88]

Very tank you!

[@armandogarza7059]

So every time you do anything like add a leveling kit or install bigger tires ,you have to proceed with these steps

[@Mario-hd5se]

Question I never had the traction light and abs light on but I change my clock spring because it went bad now my horn and cruise works fine but those two lights came on do I need to replace steering sensor or just recalibrate ?

[@themodernmechanic428]

You need to calibrate it

[@martinetvictorlartey5492]

Hi good job good video i love it. Can you please send me a link to the scanner you bought.

[@ChanceB1111]

Is this for models 2011 as well? Replacing mine today

[@tonkax360]

I have question if install a used rack and pinion can this be reprogram

[@themodernmechanic428]

Yes. This scanner would be able to program the rack and pinion

[@wolfnorth7075]

Hi. what scanner are you using? is it expensive? thanks.

[@martinetvictorlartey5492]

Hi there, I want to know what scanner he uses, did he reply you?

[@JaKobe24]

@@martinetvictorlartey5492 its an autel at least 2-3k

[@cyrusthefather7133]

Is it the same process for 2018 chevy Silverado?

[@yousifmorsy6511]

When I tried to read live data of stearing angel sensor and turned the weel to max right it gives 760, and to max left -720, but the standered range should read -720/+720, so what to do now ? is it sensor problem or need calibration or reset ?

[@flightmedic7169]

My 2018 Cadillac XT5 is doing a weird humming noise after replacing the steering rack and the wheel is not aligned. I get a code that’s says steering wheel angle calibration not learned.

[@timhudgins3257]

What kind of autel scanner are you using?

[@themodernmechanic428]

It’s an autel MaxiSys

[@Isaac-lo7yc]

@@themodernmechanic428 what model MaxiSYs ??

[@marcogutierrez1506]

@@Isaac-lo7yc same question here...!

[@naralvjorge213]

Anyone get an answer?

[@2slofouru]

@@naralvjorge213 he's never given the actual model number in any videos, and tells you to click a Amazon link to see the model. I'll pass on the click bait.

[@bhonggacutan3449]

Is it the same procedure on Ford ranger sir?

[@erickramirez5372]

No ford and gm are separate systems.

[@drewgsands]

2007 Hummer?

[@mountainvalley5169]

I have replaced my EPS motor and done a calibration with my scantool, and now the instrument cluster says service 4x4, service stabitrak, service traction control, and I don't know what to do now.

[@carbonsteelbladetheorigina7993]

Out of curiosity, what was the problem?

[@frankyq21]

Bro I need this. Where are you located ? Do you have a shop?

[@themodernmechanic428]

I'm located in SoCal. Shop is in Pomona, CA

[@frankyq21]

@@themodernmechanic428 hell yea bro can i bring in my truck to you? i need this done asap.

[@frankyq21]

@@themodernmechanic428 whats is your name and the name of your shop?

[@kennethmoyer2858]

What about programming a new power steering model?

[@themodernmechanic428]

To program modules on any GM vehicle you need to use their SPS2 software with a laptop and a j2534 pass thru device.

[@ivanvelado5463]

Yo cambie el sensor steering clockspring y mequedo esa lus ensendida

[@autoexcellence7358]

Good

[@abdiaspablo7130]

Stirring still making strength noise

[@motika64]

This happened to me after try to programa an additional key with an inexperienced technician, after reading a post that unplugging the battery for 10min the message will disappear, I tried and it works. Be careful not to break the nut that tightens the battery positive pole because it happend to me