Camaro SS And Texas Speed Headers

www.WhiteCollarGreaseMonkey.com
5 Cents Back by Audionautix is licensed under a Creative Commons Attribution license (creativecommons.org/licenses/by/4.0/)
Artist: audionautix.com/

[@SonicH6265]

Sounds really good! Can’t wait to do mine..... thanks for the video

[@MrFrost-xh6rf]

That’s what I want.. longer power band. 2011 2SS manual, Completely stock it only starts around 3K. The clip of y’all driving has me sold on long tubes.

[@jasonreyna7615]

Beautiful. I have a 2010 Camaro SS and a 98 Z28 in my garage both 6 speed

[@Ws6Ms]

niceeee I have a 2010 as 6 speed and 2002 ws6 auto..💪💪💪

[@cesargonzalez1521]

Would you ever get an automatic ss? Why not?

[@La.Ron9]

@@cesargonzalez1521 i have one putting my long tubes on tomorrow or the next day.

[@gjodexter]

You will need two people. One on top the other under the car. It’s a good three hours from start to finish. Make sure to heat up around you O2 sensors before you try to remove them. If you don’t they will strip. Good luck.

[@Ennis09]

Hey fellow Michiganders! I’m getting ready to do mine in a few weeks. How long did it take? Did y’all run into any issues? Mines not winter driven, 58k miles 2010. I suspect bolts should come off easily.

[@nomnomtron]

Sounds great. High flows or catless?

[@gjodexter]

nomnomtron catless

[@morajorge38]

Was this on a stock exhaust? I just installed a corsa catback extreme exhaust and looking to install tsp long tubes on my 12 ss

[@gjodexter]

He said dynomax just after the video started.

[@rajuncajun968]

Did ya'll change the spark plugs out for new ones during the install?

[@gjodexter]

RajunCajun96 yes.

[@rajuncajun968]

Ok sweet. Just ordered a pair for my 2012 SS, very excited to install!

[@gjodexter]

RajunCajun96 nice.

[@simplybuilt_1708]

I know it's not the same thing but would a heat gun work to remove the sensors?

[@gjodexter]

Possibly but it would sure take awhile. Just buy a small torch used for soldering copper water lines.

[@White_Snake69]

Use Map gas gets hotter

[@ashleysikes.1236]

No cats

[@XUGKgAMeR]

So the headers were 1 7/8 without cats?

[@gjodexter]

XUGKgAMeR that’s correct.

[@oscarmontoya8769]

I jus got my long tubes... Will it run fine if i dont have a tuner to eliminate the rear sensor

[@gjodexter]

Oscar Montoya did you install catted connections? If not you will run lean at the top and also have a check engine light showing,

[@oscarmontoya8769]

@@gjodexter i have the off road conectors/straight pipe... thanks for the response i appreciate it.

[@user-kp6ld8qg6w]

Everything else is stock except for the headers?

[@gjodexter]

yes. he added a tuner later on.

[@bingobango170]

Any difference in power with the new headers ?

[@gjodexter]

Bingo Bango definitely. The tuner also removed the need for the rear O2 sensors. No check engine light was set. Power gain of about 15 to 20 wheel I would estimate.

[@bingobango170]

That’s great thanks. FYI I recognize that area. I used to live on enismore on woodhul lake. I’m over in white lake now. I have a 2013 ss1LE. And I used to live on Dvorak off of maybe road. You drove by that street in this video 😂

[@keyanutate6127]

White Collar Grease Monkey is that with or without the tune?

[@White_Snake69]

Use Map gas

[@lyfsavr3489]

what tuner is he running?

[@gjodexter]

lyfsavr3489 SCT. I believe they were one of the companies that got nailed for allowing you to turn off the rear O2 sensors.

[@jeffhammer79]

I plan on doing the same to my 12 ls3. I have the dynamic and a cold air. If I get the sct with the catted version will I need to turn off the rear o2?

[@jeffhammer79]

Dynomax

[@gjodexter]

jeffhammer79 no headers no problem, catted headers, it’s up in the air if it will set codes or not.