CAN-AM RYKER - Baja Ron Sway Bar End Links: Install and Review

[@chulow9024]

I've looked at alot of male videos an they show how to videos of this... but it took a woman to do it right to explain in details of why to change it. Thank you ma'am!!! 😊

[@AnthonyLGreen-cz9wy]

Hey Beth, just wanted to let you know, I installed these yesterday and had the same issue you did with the bottom washer. So what I did was I used a pair of NEEDLE NOSE PLIERS. That way it was easier for me to hold the washer in place in front of the hole. It was so much easier. Just wanted to let you know so you could pass that along to your viewers. Thanks for all you do

[@RykerRydes]

Great tip Anthony! I love when people post ways to make the install easier. Yes, people will read the comments, so thank you for posting!

[@angiesaunders6015]

I tried the needle nose and found it to hard to get them in there. So I did it by hand and gently let the washer slide down and pushed the bolt right through it. Perfect timing. One was easier than the other if course..

[@alvaroguerrero7681]

I just installed them and what a difference, great product. I have an installation tip for the bottom side to share. I cut a piece of cardboard thick enough to fit snug in the eyelet and long enough to hold the spacers at both sides + a short section to go through both holes in the U bracket/support. Slide the link with the spacers all held together by the cardboard in place and then push out the cardboard with the screw. It is easy and only takes a few seconds and no need to hold it with your hand so bit are free.

[@RykerRydes]

Great tip!! Thank you!!!!!!!! I am sure this will help a lot of people!

[@cjctucson7683]

Beth is right on how hard that one washer is to put in place. I think I finally got the best way. I took a piece of a plastic straw from the restaurant and cut it off so it is just a little longer than fitting all the way through the lower bar. I then pulled it back a little and put a washer on it. I then put some kids putty around the straw at the hole where the difficult washer will go. I then pressed the washer against the putty real hard. While holding it in place, I withdrew the straw. Then I went about the steps of bolt in, washer on bolt, bolt through the end of the end link, then I pushed the bolt all the way through the difficult washer and out the exit hole. Add the nut on the end. Yes, it leaves a little putty there, but you can either use a toothpick or cotton swab to push some of that off, or you can know it will dry up and just drop off with use. Either way, it does not hinder the movement of the link on its own swivels. Good luck. I hope I saved you the hour of frustration I had before I figured out this way.

[@RykerRydes]

Great tip!!! Thanks for sharing!!!

[@angiesaunders6015]

Husband got me the links for Christmas and I'm getting ready to tackle this project. Thanks for giving me the power to do it myself

[@RykerRydes]

That’s so awesome!! How did it turn out?

[@angiesaunders6015]

@@RykerRydes great. It was easier than I expected. So proud of me

[@patriciafautsch432]

Using the painter tape to hold washer to back of billet worked great! Thanks to the guy who recommended that!

[@RykerRydes]

Great tip! I love when subs jump in and make helpful recommendations. That's what this channel is all about. Helping one another.

[@BlackphoenixEntertainment]

A swaybar is on my list of things to do for next year. I need to start working on my suspension.

[@RykerRydes]

Yeah, suspension and sway bar make a big difference on the ride. I'd like to do my suspension too, although I think that'll have to wait!

[@giovannam925]

Got mine in today and put them in, was an easy install besides that one washer!. Going for a test ride in the morning.

[@RykerRydes]

Right! That ONE washer! lol I thought of an idea of putting a string through it to help it attach? What is your assessment after your test ride?

[@jasong5353]

I just watched your vid to help guide me on the install. Noticed the stock ones the nut and bolt were backwards. Not sure if it matters or not. Just took it out for a test ride through some twisties and I already notice a huge difference. Feels may more planted and has a lot less body roll. Great mod and worth the price.I used a piece of painters tape and attached the washer on it. Made those bottom washers a breeze.

[@RykerRydes]

So glad you like them. Baja Ron makes a great product!!

[@patriciafautsch432]

Great idea! I will use that!

[@toboldygo5823]

And anti-sway bar doesn’t let the momentum of a turn drag the ass of the bike around. Thank you for showing me this Beth I’m gonna buy one and put it in it stabilizes the machine that much more👍🏻

[@RykerRydes]

Awesome! Thanks so much for watching!

[@tatianagamez]

I'm about to install the end links that I won from your page. Here's a tip: Cutting a straw helps keeps the washers in place until the screw goes in pushing the straw to come out.

[@RykerRydes]

Awesome tip!!!

[@6431harry]

Hi Beth I installed the Spyder Extras Billet Aluminum End Links from Sling Mod. You already know, it's funny we are on the same page. I love them, the cornering is fantastic and at 70 mph it takes away the back and forth motion. Everything is much tighter. I'm excited to see what the whole sway bar performance does. Thanks for another great video.

[@RykerRydes]

That is awesome! I am excited too!

[@6431harry]

@@RykerRydes Do you feel you have to pull harder on the bars now the end links are in? I feel I have to pull harder, maybe I hit turns at a faster speed. I know I will be buying the Baja Ron Sway bar kit. I'm turning into a mad accessory guy.

[@6431harry]

Next, the muffler Oh the madness.

[@RykerRydes]

@@6431harry OMG really? I just switched mine out YESTERDAY! We really are in sync!

[@sjustice5254]

What kills me is all the extra crap 💩 you have to order that should have been done in the factory 🏭 in the first bloody place! Windshield Backrest are installed .. now I have to get this because I don’t feel comfortable going to the town next to me! It’s insane.

[@cjctucson7683]

Just got these for my Ryker. Nice to know the hard parts so I have things ready. I am pretty sure the bolts on both sides are 10 mm so you are not using a pliers which can slip so easy and smooth the bolts/nuts. One other part is that the install of the end links is fairly easy, but I would need a mechanic to do the install of the sway bar. So glad to try the end links first. Lastly, an old mechanics trick to hold that washer in place, just chew a PIECE OF GUM and use a little bit to hold the washer against the solid part. No need to mess with super glue. Lastly if you read this far, where did you get that simple extension bar for your shifter? There are always many You Tube vids on these projects, but I always go to yours first. Thanks for all your help.

[@RykerRydes]

Great tip with the gum!!! Check out my very first video. It’s on the extender with a link in the description.

[@rejji7]

Hi my Ryker angel as you know i pick up my Ryker on Friday but what i’m noticing after watching these videos is that a lot of people are always buying/adding parts which are not cheap to get better performance, seems like it never ends is this just a part of the BIKE club for serious long distance riders, seems to me if you always have to keep buying stuff that Can Am needs to up their Ryker performance or is this stuff ppl are doing more or less just optional, lol I see your very macanically gifted, great videos, Happy Safe Riding

[@RykerRydes]

Ok first of all, I think it is so kind that you call me your Ryker angel! That is probably the best compliment I have heard! Would you care to share your first name, so I can address you properly, instead of rejj7? lol! As far as the accessories, yes people go crazy (me included) but it is TOTALLY NOT NECESSARY! Some buy the bike because it is so customizable, but not nothing is needed for the bike to have an amazing experience on the bike. It has PLENTY of power just the way it is. Also, as far as me being mechanically gifted....I have NEVER worked on a car or bike in my life. Nothing mechanical at all. That is the reason for my videos, to show people that even if I can do a project, they can too. Plus it saves everyone a lot of money not having to go to the dealership and pay crazy prices for their labor!

[@wavshrdr8452]

Beth - great channel so I subscribed. I would differ on the needfulness of some of the products you have reviewed, as have others. One thing for everyone to keep in mind is that all vehicles are built to a price point. It is obvious there are some shortcomings with the Ryker. Given its very low price point, it is to be expected. There are some things they did very well as they got a lot of the key things right. If you follow the aftermarket industry, you'll see where enough people have found issues to support parts being made to address the issues they have with the Ryker. Maybe you won't have the same issues, maybe you will. Thankfully there are enough Rykers out there to support a robust aftermarket with a lot of offerings to customize your ride as you see fit. Or address the issues you have. You may be very happy with the stock Ryker and how you ride it may be just fine for how you ride. The one thing I would encourage everyone to do is buy the 900 version over the 600 if you can afford it. You'll never regret having the extra HP and likely the resale will hold up better. There are several things Can-am could have done better from the start. Some things to start with would be better horn (wouldn't have added much cost), heated grip option, cruise control option, better seat, better suspension (with remote preload), better mirrors, get rid of the horrible DSS key, bigger motor option, hand brake in addition to the foot brake, and get rid of the clunk when you take off. Having said that it is a lot of fun to ride and few new vehicles at this price point offer the amount of fun the Ryker offers. Still an extra $500 or so the manufacturer level could have made for a much better ride that would cost us thousands to do what they could have for the $500 or so. Beth's videos are always fun to watch and can help you build the Ryker you wish the factory had made for you.

[@steelgong]

Great vid. I just fitted SpyderExtra end links from Slingmods. They supplied a little grub screw that holds the washers in place and makes them super easy to fit.

[@RykerRydes]

That's very cool! I think a piece of string might work too? Just pull it through once the washer is in place?

[@showlom]

Thank you so much for your videos. This was very helpful to help me switch my end links. I am a new Ryker rider and your videos were a strong push for me to get one. Keep up the good work.

[@RykerRydes]

Thank you so much!! Please check out my online store: www.RykerRydes.com

[@paulgoold1055]

Amazing video. This just moved higher up on my wish list. Thanks Beth!

[@RykerRydes]

Glad it was helpful! Stay safe Paul!!

[@mikeyuberalles]

Excellent video, Beth. I've been wondering about this upgrade. I just purchased a set as well. Thanks for addressing this one.

[@RykerRydes]

You are so welcome!

[@bobbelbeck2247]

FYI: A small forceps makes putting the washers on quick and simple. 10 minutes a side with a 10mm socket and wrench. Tighter steering, less hwy sway, no skipping on sharp curves, less wild when hitting bumps. A necessary mod.

[@RykerRydes]

Great tip!! Thanks for your review too!

[@budyser365]

I am glad the links make a difference and are not bad to replace. Looking forward to hearing what you think with the full replacement done next week. This is something that I may be interested in. Thanks for the great video.

[@RykerRydes]

You and me both! Stay well Mark!

[@Xonid1]

I'm changing mine now. I have those fender lights too.

[@RykerRydes]

Awesome!!! I love it!!

[@lindaadams9007]

Just installed my end links thanks to you.

[@RykerRydes]

My pleasure! What do you think? Se an improvement?

[@lindaadams9007]

@@RykerRydes Really like the ride now. Thinking about the sway bar.

[@margaretbride9606]

Tks for your help. My husband makes me do all the up grade to my ryker so I need all the help I can get.

[@RykerRydes]

Happy to help! Girl power!! If I can do it, so can you!

[@wizardfitz1]

Great job as usual, just watched and installed a horn, rear shifter and risers with help,of your vids

[@RykerRydes]

Nice work! I am so happy you find my videos helpful...that's why I do them!

[@sjustice5254]

What kills me is all the extra crap 💩 you have to order that should have been done in the factory 🏭 in the first bloody place! Windshield Backrest are installed .. now I have to get this because I don’t feel comfortable going to the town next to me! It’s insane.

[@medina8050]

You are one of the best ...THANKS FOR POSTING

[@RykerRydes]

So nice of you! Thank you very much!!

[@tracimarra6261]

Great video. Hoping you have one for adding led lights

[@RykerRydes]

Thanks for watching! Yes I have tons of new LED light videos and also sell them on my website RykerRydes.com

[@maddmechanic2386]

Word of caution, you should use blue loctite on them. They're not nylon threaded nuts. They could back off

[@RykerRydes]

I 100% trust Baja Ron, and he clearly does not want anyone using Loctite on them. Please contact him directly regarding that. I would not want to change the function of the links (which are pre oiled)

[@maddmechanic2386]

Oh ok, what part of florida do live. Im in Lakeland

[@tomisham9900]

Very good! I will get the blue ones too because it is my favorite color, my pickup truck is blue.

[@RykerRydes]

Good choice! Clearly that is my favorite color too!

[@dirkdiggler2379]

Just installed mine the difference is huge! smoother turning thats for sure. Also noticed my left side OEM links bolt's & nuts were backwards!! they were either put there by the dealer backwards but I fixed them with the new links. I wonder if that was the reason why my turning wasn't as smooth and just shaky.. who knows.

[@RykerRydes]

So glad they work so well for you. I agree, I was shocked by the difference.

[@sjustice5254]

What about highway speeds?

[@bobbelbeck2247]

It apears the factory puts the bolts on opposite ways on each side. IMHO, it is because one side does not have the clearance necessary, the other does.

[@GRIM_MOD]

Getting these next week

[@RykerRydes]

You are going to love them. Keep us posted!

[@GRIM_MOD]

@@RykerRydes Will do!

[@TheBorderRyker]

Ooooh. Now I want a set of those. Those are definitely at the top of my Christmas list 😁. They look fantastic 👌🏻. Brilliant video as always Beth, and the T-Shirts look awesome. I can’t wait for the next instalment. Ryde Safe Beth 🙏🏻😎🏴󠁧󠁢󠁳󠁣󠁴󠁿

[@RykerRydes]

Glad you like them! Thanks so much George!! They are pretty AND functional!

[@jimmymelendez7408]

Great video. Can’t wait for part 2.

[@RykerRydes]

Me neither! lot!!

[@richardbrown3357]

How soon will you be posting a video on the complete sway bar install? Thanks

[@RykerRydes]

Richard Brown it’ll be out this Thursday!!! Stay tuned!!

[@CeeDeeLight]

Great Video as usual Beth!

[@RykerRydes]

Thanks for always watching!!

[@wendy8739]

Thank for the great explanation. It’s something I’ve wondered about. Thanks and be safe

[@RykerRydes]

Glad to help! Stay safe!!

[@RideAboutNow]

Nice vid RR. I just had the factory add on installed by the dealer, and it made a world of difference in handling. the flext from turns are much more controllable. Are you changing the sway bar out as well? I wonder how much stiffer the bike will get with the metal links.

[@RykerRydes]

I agree, the links made a huge difference!

[@sjustice5254]

What kills me is all the extra crap 💩 you have to order that should have been done in the factory 🏭 in the first bloody place! Windshield Backrest are installed .. now I have to get this because I don’t feel comfortable going to the town next to me! It’s insane.

[@RideAboutNow]

@@sjustice5254 I know it's something that should've been standard from factory

[@sjustice5254]

@@RideAboutNow yes absolutely ridiculous. there is enough additional shit you have to buy

[@kevinperry368]

Thanks for addressing this topic! Was waiting for you to do so. Will withhold my final decision to replace after your second video. Are you having issues with squeaky brakes? I hear it on other Rykers so I know it's not just mine. I don't see any brake upgrades out there yet. My guess is the linked braking system is doing nothing to avoid putting too much heat into the pads and rotors causing glazing, a typical issue with front brakes after stop and go riding on a motorcycle.

[@thatdudesinc.5636]

Kevin, LaMonster Garage offers an upgraded brake system. Here is the link to check them out... www.lamonstergarage.com/high-performance-ebc-front-brake-pads-all-can-am-rykers-lamonster/ I'm thinking about trying this out soon.

[@RykerRydes]

Hey Kevin! As always, thanks for watching! Sorry but I do not have any squeaky brake issues. I have heard other complain about it. I would think there must be s brake upgrade you and do? I would love them to be more responsive and less squishy.

[@indigoduce]

Hi.I have a question...when highway riding and I hit a bump, i feel out of control....will these help with that... Thank you....great video's...

[@RykerRydes]

Yes and no. It definitely helps but you will still feel the bumps. Not the best answer, I know. I am actually trying to get Baja Ron to join the chat so he can answer these questions.

[@jf6720]

I think you left an important part out. It looks like you took the front fascia off, I think that should have been included in the video since you can't do anything until you remove it.

[@RykerRydes]

I have showed how to take that part off in many other videos. Please refer to my grill guard video. Ps sorry for the late response. I’m still on my bike trip.

[@jf6720]

@@RykerRydes Thank you, enjoy your trip!

[@Daniel_Size_12]

Does the color make a difference in which ones to choose, or is it just a preference.

[@RykerRydes]

Hi Daniel, the color is strictly preference only.

[@scott-lc8xc]

Hey Beth. I saw a review of the end links and the guy said it takes more effort to turn. As in using more strength to push/pull the handle bars. Did you find this to be true? If so, how much more effort? Thanks.

[@RykerRydes]

scott I did read that comment, but I honestly have know idea what he’s talking about. The links give you better handling, not harder steering.

[@scott-lc8xc]

@@RykerRydes I thought it would be an odd effect of the upgrade and didn't make sense to me. But I'm new to Rykers so figured I'd check. Thanks for the quick reply!

[@RykerRydes]

Any time!!

[@ryker4124]

Don't forget the thread locker 🤔, and a dab of grease holds the spacers in place during install.

[@RykerRydes]

Great tips!

[@ryker4124]

@@RykerRydes the kit now comes with a tiny wooden dowel to solve the issue with the spacers. BTW, your email survey doesn't work.

[@kirkd.6371]

After riding on the highway for the first and then having a truck fly by me. I am definitely going to change links out. Now I do have a question. Slingmods has the option to buy and add a hand brake to the ryker. Do you think it’s a good upgrade or waste of money??

[@RykerRydes]

Why do you need a hand brake? That’s the $1,600 question. It’s good if you are coming off of 2 wheels and you are used to braking like that, or if you are disabled. Other than that…. not sure. Don’t forget to check out my Etsy page for BajaRon sway bars and links.

[@jamesglenn520]

Are the links longer or shorter than the factory ones? And are they adjustable at all?

[@RykerRydes]

The links are the same size. No they are not adjustable. Thanks for watching.

[@sandramckee6422]

Good Morning, I was just wondering since I have the 2020 Ryker Rally did they upgrade the links?

[@RykerRydes]

GREAT question. I do not know the answer. But if was a betting person, I'd have to guess they did NOT upgrade the links or sway bar.

[@MichaelFinkSunCommercialSolar]

I just got a 2021 900 Ace, they did not upgrade them. I order some from slingmods.com

[@253681577]

Thank you very helpful ❤

[@RykerRydes]

You're welcome 😊

[@williamgillen8846]

Did you use a torque wrench to tighten it to 85 or 89 lbs or just tighten it. Other videos use torque wrench to 85 or 89 lbs. thanks

[@RykerRydes]

Yes, you should always torque to speck. I don’t always do it though. 😬

[@jasonstroud01]

I used a torque wrench on my bottom and snapped the bolt in half last night . I spec’d it correctly too . Guess who’s not driving right now until I get another bolt and scared to touch this install right now … this guy .

[@patriciafautsch432]

Do you recommend putting blue lok tite on threads of bolts?

[@patriciafautsch432]

I later saw comment on lok tite

[@teresamorgan6486]

I just bought a Ryker with the Baja Ron sway bar and links already installed. I have been having the VSS fault come up twice now. Since the sway bar would be part of the stability of the bike I was wondering if there are any adjustments. I have looked all over the internet and all I'm finding are installation instructions. Can anyone help me with this question?

[@RykerRydes]

Hmm the Sway Bar shouldn’t give you a vss code. There are lots of reasons for the code. Are there any numbers or letters that come after vss? You may want to swing by a dealership and have them check it out. Be sure you aren’t riding the brake. That is a common reason for that code. Good luck.

[@FanouSL]

Thank you!

[@RykerRydes]

My pleasure. Thanks for watching!!

[@patriciafautsch432]

I don't have a real torquewrench, jusr standard set. Am i able to correctly tighten the nuts with the standard driver?

[@RykerRydes]

Off the record…yes you can tighten them down without a torque wrench.

[@michaelmcglone7591]

Beth, do you know what you torque the bolts to?

[@RykerRydes]

Yes, sorry I should have put that in the video: Torque value of 15lb ft or 180 inch pounds

[@michaelmcglone7591]

@@RykerRydes Thanks for the info.

[@antanasmarmokas9628]

Good video i will buy this

[@RykerRydes]

Awesome!

[@sjustice5254]

I bought Alpha Rider brand.. look the same .should work the same

[@RykerRydes]

Please be careful using cheap knockoffs. I want you to be safe.

[@sjustice5254]

@@RykerRydes thanks dear me too. they have to be better than the cheap knockoffs they installed when they built it though..lol

[@GrumpySpyder-Ryder]

Great video!

[@RykerRydes]

Glad you enjoyed it

[@GrumpySpyder-Ryder]

Ryker Rydes As always, it was very informative.

[@aimee19800]

Hey I love your video, you have save me so much money.. can you please put a link to it please

[@RykerRydes]

Were you able to find the link in the description section? The first link I posted was broken!

[@BykerDog]

I am getting ready to replace the end links on mine, why did you chose this brand?

[@RykerRydes]

Great question! I chose this brand because of the sway bar. It is so much easier to install than the other one piece systems. My video on the sway bar installation is coming soon!

[@Charlotte071]

Did U raise the bike or keep it flat?

[@RykerRydes]

No need to raise the bike, super easy to install with huge results!

[@Rtburch]

If I get the BajaRon Sway Bar Links/Heim Joints is it necessary to change the sway bar?

[@RykerRydes]

No. It is not necessary. I found quite a bit of difference when I changed out just the links. If you buy the links from www.customspyderworks.com and you change your mind later and want to add the sway bar, he will sell you the partial kit.

[@inyourseat]

What size socket to remove the bolt

[@RykerRydes]

It was a while ago, let me text Baja Ron......

[@inyourseat]

Got it taken care just looked back further in you video thank you though

[@RykerRydes]

10mm?

[@deaf_sp_okiehopper]

Yes 10mm socket and 10mm wrench. I installed the bajaron end links myself with this KZbin as my guide.

[@GrillPiece63]

Question: is there a torque spec needed for this?

[@RykerRydes]

Sorry for the delay. I was waiting for a response from Baja Ron: "Ryker Link Torque - Torque value is 85 inch pounds. Personally, I don't advise using a torque wrench on the end links. They just need to be tight. It is too easy to twist off a bolt with a torque wrench because you have no feel. Also, torque wrenches can get out of calibration if you are not careful with them. I've never had a link bolt come off. The nylon lock nuts prevent this." Ron (bajaron) 423-552-3720

[@GrillPiece63]

@@RykerRydes thank you for the info.

[@VinCode17]

Wish I would've read this 5 minutes ago. I just broke a nut & bolt trying to do it with inch lb torque wrench set at 89 smh

[@jasonstroud01]

@@VinCode17I just did the exact same thing last night ! Snapped right in half ! What you do to fix it ?

[@VinCode17]

@@jasonstroud01 I just used the old bolt & nut 😂

[@andresfeliperamirezrestrepo]

Hi Beth I'm having problems with my Ryker stability when riding 55mph or above, would this links help?

[@RykerRydes]

YES! But it could be your tire air pressure, or you may need a laser alignment. Hard to tell from here. Either way, the links will help A LOT and you will notice a difference right away. LMK what you decide.

[@garynash6082]

Does it fix or not?

[@RykerRydes]

Yes!!!!

[@MrJmduffy]

👍👍

[@sjustice5254]

What kills me is all the extra crap 💩 you have to order that should have been done in the factory 🏭 in the first bloody place! Windshield Backrest are installed .. now I have to get this because I don’t feel comfortable going to the town next to me! It’s insane.

[@RykerRydes]

I understand. Nothing is essential, just personal preference. The Ryker runs great as is.

[@bobbelbeck2247]

I did very little to my first Ryker 600 other than a windshield and passenger seat and it was perfectly fine. Depends on how you ride it. My new 900 Sport was kind of sticky around 90 degree curves, so I did this mod asap.

[@auggy53]

i hope your right , i just bought a set5 minutes ago

[@RykerRydes]

You will not regret it!

[@rykerryd3r59]

Thanks for a great video. What made you decide to go with Baja Ron Sway Bar End Links instead of the SpyderExtras Aluminum Sway Bar End Links from SlingMods? I’m trying to decide between the two.

[@RykerRydes]

I think this is the #1 question I get. The simple answer is: the Baja Ron one comes in 3 pieces instead of one, which makes it considerably easier to but on (I hope). I plan on doing it this week!

[@randyk7699]

Great vid!

[@RykerRydes]

Thanks Randy!