CAN AM X3 HOW TO REPLACED CLUTCH HOUSING WITH MR RPM ALUMINUM DIY EP - 108

[@dblockchain]

I just broke my first belt and shot out the bottom housing. I noticed it’s not reading the belt temp and the ! Light came on. Thank you for this video 🙏🏼

[@GLifeUTV]

🤜🤛

[@alanwright782]

I ended up getting a full carbon fiber liner that just slides into place. No rivets or screws needed to hold, it’s pressure fitted. Easiest install I’ve done on the x3 yet.

[@GLifeUTV]

Yea, I like the CF liners. We did one on my buddies X3.

[@dannylsx]

link?

[@Sayntzkilla1]

What size and where to buy the secondary clutch puller?

[@ОлегЛизун]

hi what is the tightening torque for primary and secondary CVT bolts on Maverick X3 turbo 2021?

[@daequanshambley1621]

Glife, I'm grateful for you brother. I'm new to the Maverick and I just got a used one, I've watched your videos a couple times but I'm coming back to say thank you for your help

[@GLifeUTV]

I appreciate it

[@304trails8]

So I was cleaning the intake cover and things out in the bed and by my luck a piece of mud about the size of the end of your thumb rolled down into the intake tube that goes down behind the primary clutch. Wondering if anyone knows if that a big deal where it looks like the housing is made where that little plastic cover behind the primary would keep it from getting into the primary and it’s just gonna chill there till I decide to do a clutch kit or something wjere I would go ahead and pull the clutch all the way off and remove that little cover and get that mud out. Wondering if you would think it’s a big deal or not since you’ve had it apart and understand a little better on how it’s designed.

[@GLifeUTV]

Possibly could have a rock n that little piece of mud. Id pull it out

[@n2rescue359]

Folded metal makes a liner also, along with radio mounts

[@GLifeUTV]

Good to know on that👍

[@zackmansir2231]

Have you had any issues with the case? I put one on and now I have an oil leak behind the case at the primary clutch, it leaks down the back of the case. I contacted Mr rpm and he sent me new hardware to bolt the case on. I redid it with the hardware and still have a leak.

[@GLifeUTV]

U need a new pto cover gasket. And when u install the housing u can not overtightened the bolts for the housing on the primary side or it will pull the pto cover away and cause the leak. The torque spec is something like 89 in lbs or something id have to look it up... Key word inch lbs.. not foot. lbs .. use plenty of loctite

[@zackmansir2231]

OK thx man

[@littleSLEEPY-r1x]

@@GLifeUTV i know this is old but I’m having the same problem after installing the cover. is there anyway you can link where to find the gasket because I can’t seem to find it anywhere?

[@GLifeUTV]

@@littleSLEEPY-r1x I Believe this is it.. you can also use the can am parts website to verify number.... www.warrantykillerperformance.com/products/can-am-maverick-x3-pto-cover-gasket can-am-shop.brp.com/off-road/us/en/shop/sales/parts/

[@littleSLEEPY-r1x]

@@GLifeUTV thank you soo much!! 🤘🏼

[@AmbrosioCebreros-r1o]

Where did you get that plate for the license plate are the tags

[@GLifeUTV]

Axia

[@codyt3746]

How is this holding up and is it worth buying over the liners? And have you have water issues or with the plastic housing lining up and holding up ?

[@GLifeUTV]

So far so good. But mainly dry desert. And occasional water crossing... Lined up fairly good. No issues

[@rudeboi7923]

What’s the name of the tool and where can I order it from? That you used to pull the clutch off.??

[@rudeboi7923]

Your video’s are awesome..! And I learn from watching them. Thanks brother

[@GLifeUTV]

www.glifeutv.com/products/can-am-maverick-x3-maverick-1000-and-maverick-1000-turbo-clutch-puller?_pos=1&_sid=582d4d7e7&_ss=r

[@isaiashernandez1857]

Where did you get the clutch removing tool get you add the link

[@GLifeUTV]

kwiclutching.com/kwistore/puller

[@chrissanchez3253]

Hey can you still use it even if it’s cracked

[@GLifeUTV]

U shouldn't

[@ungureanurazvan-dumitrel4482]

Thanks for the video. Question: Do you by any chance have the part number or a link for the primary clutch puller? I’ve seen a lot of bad reviews about some of they breaking and causing more damage than you would like, thanks!

[@GLifeUTV]

i purchased my primary clutch puller from kwi and have had no issues.

[@95toycrawler]

Do you still use this clutch housing ? Have you had any problems with it ?

[@GLifeUTV]

Yup still on my machine

[@95toycrawler]

Have you done the quick release pin kit where you drill out the holes ?

[@GLifeUTV]

@@95toycrawler i have not

[@biggreeneeg]

Hey Frankie where did you purchase the housing ?

[@GLifeUTV]

www.mrrpmcycle.com/

[@mynihilism]

Frank, just ran across you channel a couple days back and have been binge watching. Fantastic information and how too's along with a good amount of laughs. Keep up the great work man. I'm sure I will be at least referencing your shock setup video when my 21 DS Turbo RR shows up this month.

[@GLifeUTV]

Hey thanks, i appreciate you commenting and watching the vids.. we will be doing some light installs too on my buddies 2021. So stay tuned🤟

[@born2ride146]

Hey man I thought your had to tighten the clutches to a certain torque ? Or am I wrong ? Have you had any problems with it by the way your tightened it ? Thx

[@GLifeUTV]

Im sure there is a torque spec. I havnt had any issues.. but i do suggest u torque it down for ur piece of mind.. also i recommend to clean out the grease as best as possible 👍

[@born2ride146]

@@GLifeUTV awesome thank you I have a 2020 x3 base model I have about 1100 miles on it and surprisingly haven’t blown a belt and I drive it pretty hard so I’m thinking in getting the metal liner before I blow the belt which I don’t think it’s gonna take much longer

[@GLifeUTV]

@@born2ride146 at 1100 miles. Personally.. go ahead and replace the belt with a new one before it breaks..

[@born2ride146]

@@GLifeUTV yah your right maybe I should cause I always carry an extra I have a evo’s worlds best belt as a spark right now

[@dannicole441]

I just installed my Mr RPM cover and used the grease. Was the grease an issue? Did it get on your belt once you ran it?

[@mariobarajas7002]

Question what is your impact mid or high output?

[@GLifeUTV]

High

[@mariobarajas7002]

High 1/2 18m

[@GLifeUTV]

@@mariobarajas7002 yup. Thats it. First gen m18 1/2 high torque impact wrench with friction ring.

[@mariobarajas7002]

The socond drill you use what is that one? Impact as well?

[@GLifeUTV]

@@mariobarajas7002 3/8 m18 impact wrench... These are both old versions as ive had them for years.. ill link u the more modern versions amzn.to/3IM2Ymn amzn.to/3ERhAyA

[@blakedavis4527]

Thxs for the video bro, I just blew my box up yesterday, does that kit come with a outer housing too? Or did you use the factory outer housing?

[@GLifeUTV]

You reuse oem outer housing👍👍

[@blakedavis4527]

Where did you buy the housing from? I am not finding it, I am just seeing the factory one

[@GLifeUTV]

@@blakedavis4527 www.mrrpmcycle.com/

[@ryanwong1930]

I was told by can am , the reason why the housing is plastic is cause it was designed to fail when the belt dies . Apparently its better the housing fails than the shafts warping/bending due to binding of the broken belt and the clutches .

[@GLifeUTV]

Makes sense. My last belt that failed went into pieces and shot out the front clutch exhaust. Also the pro xp I believe is an aluminum housing oem

[@ryanwong1930]

@@GLifeUTV im stuck in between . Havnt blown a belt yet , but also nevet want to haha .

[@GLifeUTV]

@@ryanwong1930 no one does bro.. its the most affordable weaklink. If it was a traditional trans.. we would be breaking parts inside the trans often..i dont mind replacing belts😁

[@gsrhatch14]

Then they should make replacements cheaper

[@cmfsoul]

Where did you get your license plate holder at bro? Love your work man keep up the good content!!

[@GLifeUTV]

This is made by axia amzn.to/3e8Spw2

[@carlosgobe89]

Man some other video they make it look impossible..probably a dealer 😅. Thank you

[@GLifeUTV]

No problem 👍

[@brownhornet1515]

Bro that video was awesome ... im new to this world and i laughed and learned all the way through!!! Keep up the good work and vids 🤘🏽🤘🏻🤘🏽🤘🏻😎😎

[@GLifeUTV]

Thanks bro. Appreciate it🤘

[@nickwillis8488]

Hey bro how do you like the aluminum housing. Is it worth it? I heard some. Iced reviews about it just curious if it’s worth the money or maybe a headache, thanks brotha

[@GLifeUTV]

i have had no issues with it at all. its been great

[@buildbrothers6919]

Mr RPM doesn't show that product available any longer....dang...let me know if you have any suggestions.

[@GLifeUTV]

A carbon fiber inner liner.

[@vicspmpnful]

Whats the price?

[@GLifeUTV]

Like 450ish

[@n2rescue359]

Got any free time my cage should be done this week... Oh the joy of the installation

[@GLifeUTV]

That's gonna be fun bro...haha

[@GLifeUTV]

Where u stay at

[@n2rescue359]

FrankGLife Murrieta

[@danielgonzaga857]

Nice install bud

[@GLifeUTV]

thanks bro

[@MrCarpediempilot]

Sweet! Wish can am would have done this from the factory

[@GLifeUTV]

I dope they do someday on future models To much of s common occurrence .

[@3DProductions]

great video & editing! keep it up bro

[@GLifeUTV]

Thanks🙏🤟

[@187flatliner]

Should have serviced your clutch with it out already...

[@GLifeUTV]

your right, future video .lol

[@187flatliner]

@@GLifeUTV kwi makes like a 50 clutch service kit... got to do mine soon as well

[@GLifeUTV]

@@187flatliner yea ive been peaking around their site. they make good stuff

[@danielmakin4351]

Lmfao thats what she said 🤣

[@GLifeUTV]

😅

[@Fieldsinv]

👏 😉

[@glamisfuntopia]

What up

[@GLifeUTV]

Sup dude

[@glamisfuntopia]

FrankGLife nice ch

[@GLifeUTV]

@@glamisfuntopia thanks bro👍