CanAm G2 Gearbox ⚙️🔨🏆 how to disasembly change bad shifting sleeve and H gear popping

[@parascolaireelectroniqueet6776]

I got a 2021 650 max. Won't go in reverse, won't go in park. Grinding noise. I was worried I had to take the entire engine out. Thank you and god bless!

[@Rapsa85]

Same problem what i had

[@TheSponge945]

This video just answered my question! My secondary shaft has up and down play, noticed this while doing clutch maintenance. I assume the bearing that’s in the cover you removed is the culprit for this? Any input or feedback you got would be greatly appreciated!

[@Rapsa85]

I made this video to help others.. Nice to know. Thanks to you 😊

[@TheSponge945]

@@Rapsa85 hey, don’t think you understood my message 😂 do you know if the up and down play is due to the bearing or not?

[@Rapsa85]

There is two tapered bearings in that shaft.. It can be culprit

[@TheSponge945]

@@Rapsa85 oh really? Where is the other one? Further into the case? Because I see one that’s pressed into the cover you pulled off

[@Rapsa85]

[url=aijaa.com/W8eemL][img]img.aijaa.com/b/00558/15268889.jpg[/img][/url] [url=aijaa.com/NGHj1L][img]img.aijaa.com/b/00566/15268890.jpg[/img][/url] Sorry.. Regular ball bearing

[@TheSponge945]

What the chance of something falling off when pulling the cover off? Especially that thing in the top right (top left inside cover) ?

[@Rapsa85]

Very possible 😑

[@TheSponge945]

What did you use to put the cover back on? Looks like some sort of gasket maker?

[@Rapsa85]

It was Biltema gasket silicone

[@TheSponge945]

@@Rapsa85 no issues or leaks with this gasket silicone?

[@Rapsa85]

@@TheSponge945 no problem at all

[@jandersonguterresneni1545]

Boa noite tenho um Outlander 500 faz barulho quando solta acelerador da umas batidas na transmissão

[@Rapsa85]

Check before engine & gearbox atachments to the frame. Top motor mount can be broken and engine brake turns engine sideways and force the gear out (shifter rod turns)

[@jandersonguterresneni1545]

Há ok vou verificar

[@blackseabrew]

I have a 2013 Can Am Commander LTD 1000 that I just bought with only 900 miles. It already needs this as well as wheel bearings and tie rods ends. GRRR. Whoever bought it new rode it hard. For me it's just stricly a utility vehicle. I treat her gently so she will last until 10,000 miles.

[@Rapsa85]

Commanders broblem also. I had to do the same to my commander. There was bad lockrings on axle and H & L gear move on axle. It caused bad loose contact between sleeve&gear. i had to renew H,L,sleeves and lockrings.

[@VicToR_Rider]

Torque specs on the gear box cover?

[@Rapsa85]

[url=aijaa.com/B2yJtp][img]img.aijaa.com/t/00558/15195520.t.jpg[/img][/url]

[@JaniRunonen]

Terve, missäpäin Suomea teet can am huoltoja? Sattuu olee sama vika että isolla vaihteella heittää vaihde vapaalle. Pienellä vaihteella ei oo ongelmaa.

[@Rapsa85]

Ruokolahdella. Mielelläni kyllä autan,jos vain olet lähettyvillä.

[@DanielGutierrez-ns6lq]

So mine won’t shift to reverse or park would this be the problem

[@Rapsa85]

kzbin.info/www/bejne/jHi7XnlvlL6taqssi=Dlakz0NbDTLBGTnn

[@Rapsa85]

Check your shifter linkage also..

[@iaroslavlysenko8621]

what parts number

[@Rapsa85]

420257945

[@Rapsa85]

420845772

[@Rapsa85]

420257945

[@dsmtsi]

What are you fixing here? Does this fix the transmission not shifting into gear or popping out of gear problem? I am trying to diagnose the problem with my gear box on my can am 650 xmr

[@Rapsa85]

This fix gear popping out problem. Shifting sleeve corners are worn out and needed new ones.

[@dsmtsi]

@@Rapsa85 Was the quad popping out of gear or was it hard shifting between gears?

[@Rapsa85]

Popping out

[@Rapsa85]

If shifting is difficult its in the clutch. Oneway bearing, spring, weights, too tight belt..

[@dsmtsi]

@@Rapsa85 Clutch I brand new CVech. It has shifting problems when the quad is off as well. It also sometimes makes a horrible sounds like marbles I think it pops between gears. Happens more in low.