Thank you. I just installed the flat trigger on my Canik Mete SFX and your video was the most helpful I found, even had the same issue with the detent spring. What would’ve been a huge bonus for me, if you had shown how to hold the lil 3 piece assembly in its spot, push in and out while giving a lil jiggle until the spring pops into the correct place. You can immediately feel the difference in how far you can push down on the whole assembly. It took me also bending the spring first while trying to force in the roll pin and maybe damaging the very tip of the detent slightly before figuring this out. Also, the roll pin that comes already half way in the new Canik trigger was extremely tight and took quite some force with a 5/64 punch to get it moving. The included guide rod helped a bit but be careful not to scratch the trigger surface with your tools!
@OhioGunRunnerАй бұрын
@@philsuh5700 glad it helped.
@TheNatureBoy5257 ай бұрын
As someone also waiting on delivery of a Canik flat face to replace my MC9 factory trigger, I see a day full of cursing all things holy ahead of me.
@OhioGunRunner7 ай бұрын
It’s not bad. Spend the $8.50 on a set of roll pin punches. 5/64 roll pin punch is the cheat code. a.co/d/3Wguquv
@TheNatureBoy5257 ай бұрын
@@OhioGunRunner Thank you for the link. I ordered a set.
@TheNatureBoy5256 ай бұрын
@@OhioGunRunner As a quick update, did the swap last weekend. The only part that gave me any trouble at all was getting the pin lined up and into the trigger bar. Everything else was a breeze following along with your video each step of the way. Thank you, brother.
@leoncrandall25527 ай бұрын
Excellent video!!
@OhioGunRunner7 ай бұрын
Thank you very much!
@spaz13b24 күн бұрын
Outstanding video!! Thumbs up, Five stars and all that jazz! Thank you, sir! 🎉👏👏👏
@JD3D676 ай бұрын
I have watched several KZbin videos about swapping out a trigger on the Canik Mete series pistols, and yours is the BEST BY FAR. Thank you. I can't imagine trying to fumble through this with no help.
@berndbecker10012 ай бұрын
Thank you very much, I have just installed the Canik Flat Trigger in my Mete. Thanks to your video it was very easy. Greetings from Germany.
@OhioGunRunner2 ай бұрын
@@berndbecker1001 great. I’m glad you found it helpful. Thank you.
@roberthicks23645 ай бұрын
Thank you for this walkthrough. It was very helpful in changing out the trigger shoe on my MC9. There are a couple small differences between the pistol you are using and the MC9, but not enough to require a different video. The whole process only took about 20-25 minutes.
@OhioGunRunner5 ай бұрын
Glad it was helpful.
@robertgreen99032 ай бұрын
@@OhioGunRunner can you help me?
@OhioGunRunner2 ай бұрын
@@robertgreen9903 what do you need help with?
@tonyg84714 ай бұрын
Excellent how-to video. Thank you. Now, I just need to convince myself I want the Canik trigger shoe upgrade. I've been considering it. If I proceed, you are my go-to for the surgical procedure.
@architecturehappy5 ай бұрын
Fantastic walk through, will be using this for swapping my stock for the flat face canik trigger that just arrived, thank you!
@DougZ733 ай бұрын
Great video. Thank you so much for posting. I had bent my slide lock back mechanism little spring during a cleaning and had to change it out. This video was instrumental in helping me figure out how to get the firearm apart and replace it. Thank you again
@nightlifegamer7 ай бұрын
i got the enhanced 90 trigger, i was trying to fallow along to install the new trigger. great job showing how to break it down. but the canik 90 trigger comes with an extra pin and i have no idea if i need it or where it goes. im installing it on a mete sf. any ideas?
@OhioGunRunner7 ай бұрын
It can be used as a slave pin while installing the trigger shoe but not needed. I’ve thrown them all away with the packaging. I’ve done close to 20 of these trigger shoe replacements. Sorry I did not mention it in the video.
@hotrod90733 ай бұрын
Thank you. I am going to switch out the MC9 for a flat face.
@OhioGunRunner3 ай бұрын
@@hotrod9073 the Canik Aluminum Flat Face trigger is a great choice for the MC9.
@brodemode8126Ай бұрын
What did you dislike about the freedomamith? I have 2 zombie pros and love them. Just got the fat daddy 2 for my mc9. Hopefullyi like it as much ad my zombie pros
good video and i was wondering what optic do u have on that pistol
@OhioGunRunner4 ай бұрын
Cyelee Cat X Pro
@hotrod9073Ай бұрын
Does anyone know which canik flat face trigger works with the MC9?
@OhioGunRunnerАй бұрын
@@hotrod9073 they don’t list the MC9 but the Canik fits it fine. It does fill up the trigger guard. Probably wouldn’t work with gloves. I’ve put 4 of them in the MC9. As long as it says Mete it will fit.
@hotrod9073Ай бұрын
@@OhioGunRunner Thank you.
@joewelsh1749Ай бұрын
OMG, why?????? Just remove the trigger return spring and punch out the pin for the trigger bar. You will also have to take out the slide release, but that is all. There is no reason to remove anything else beyond that
@OhioGunRunnerАй бұрын
@@joewelsh1749 to each their own. I’ve looked at the other method but can do this way completely in 10 mins. I’ve done a few dozen now.
@joewelsh1749Ай бұрын
@@OhioGunRunner it literally take me 5 minutes. To press out the trigger pin
@OhioGunRunnerАй бұрын
@@joewelsh1749 I hear you. To each their own.
@khawajabilaljaved8965Ай бұрын
I changed the same way but trigger reset does not work