Hey guys. Thanks for watching. Please support this channel and make it grow by SUBSCRIBING and WATCHING more of my videos if you haven't already done so. Thanks so much 🤙
@richardcartwright50194 жыл бұрын
Shane your a genius mate. Just followed this vid. At first i thought oh god what have i done. But i finally got rid of the annoying clicking and squeaking sound when i pump. The board works more fluid and responsive. Also it does give you a greater understanding of how a carver board works and the level of craftsmanship that goes into making them.
@shanelai25154 жыл бұрын
I'm really glad that helped 😊
@WRandallHead Жыл бұрын
disassembled, cleaned, and pout together my whole build yesterday thanks to your vid! Feeling super confident to maintain and upgrade now, you're a legend
@vela07 Жыл бұрын
My C7 truck wasn't springy. I took it apart and cleaned it and adjusted it. Shane, you are the man, thank you so much! I don't think my C7 pumped this hard straight out of the box.
@boltup55664 жыл бұрын
Thanks. Carver should have done this long time ago.
@joeybirdjose Жыл бұрын
When I saw the wd-40 I was like ohhhh noooo. But homie hit it right on the nail 😮💨💯
@ace.hypnotika4 жыл бұрын
Thanks for the teardown. Dreading opening up my C7 truck which I've had for over a decade and never properly taken care of.
@ace.hypnotika4 жыл бұрын
Finally took apart my 2004 Carver C7 and it looked surprisingly clean and in good condition (I don't skate daily). I found the following: 1) Looks pretty much the same except no C-clip holding the spring bolt. 2) It was never greased or light grease wore off. 3) Two major areas of wear. These should have heavy grease: 1-Spring bolt wherever it contacts with the link. 2-nub on arm bearing plate which connects to the link. Hope this info helps anyone maintaining their C7🤙🏾
@CptEvil3 жыл бұрын
Thanks mate. Good video for first timers. I enjoyed it too because you showed all the internal parts and workings before I decide to buy.
@sandenofyb45618 ай бұрын
Thank you. I have 2 boards and didn't know how to maintenance. My husband's board is off and this was very informative for me to try to fix it.
@estufados14 жыл бұрын
Awesome dude thank you so much! My spring broke a long time ago and I finally received my new one but didn't know how to proceed so again, thank you!
@shanelai25154 жыл бұрын
No worries mate. Glad it helps 😊
@barrydworak5 ай бұрын
Thanks for this, Shane! I'm mechanically inclined and have fixed cars and motorcycles, house wiring, computers and other electronics, firearms, and most other devices. But for some reason I have been reluctant to disassemble ny C7. 😂 Maybe I just didn't trust those big stacks of washers to go back together. Anyway, now I have no qualms about screwing with it.
@jonathanmelamed514 жыл бұрын
This was awesome! Great tutorial, and great timing releasing the video when there's nothing else to do but skate! thank you!
@shanelai25154 жыл бұрын
Glad you like it 😊
@jonathanmelamed72514 жыл бұрын
Shane Lai hi Shane! Thank you again for the video, I’m trying it out! I noticed at 4:57 you flipped of the bottom thrust bearing.... does it matter which end of that thing points to the base? Same question applies to the top thrust bearing I guess!
@shanelai25154 жыл бұрын
@@jonathanmelamed7251 it does not matter. I had tried both ways.
@SurfSkateDX2 жыл бұрын
Parabéns pelo trabalho, Apóiem o surfSkate em Cabo frio RJ 🇧🇷 obrigado a todos 🤘
@coolbritannia1979 Жыл бұрын
Great video, just helped me fix a mistake I made with my trucks, thanks
@lacerise92174 жыл бұрын
très instructif merci
@mathieub45533 жыл бұрын
hello ! What kind of grease do we have to use ? thanks a lot !!!
@Radioduc Жыл бұрын
Shane, you da man! Great video. Peace👍.
@MrFreezook4 жыл бұрын
Thx ! this was really helpful nice and net
@TheFonzirelliz2 жыл бұрын
thank you brother.
@HoStevie2 жыл бұрын
*need this!*
@OCEANBOUND1 Жыл бұрын
Great vid, thanks dude! The music is kinda too loud but the tutorial is great.
@ericbrammer22453 жыл бұрын
Silicone Spray is a great 'cleaning lube' on these, btw!
@SnwbrdB4 жыл бұрын
If you have thoughts about adjusting for a specific rider that would be cool. I’ve experimented tight and loose front and back. Not sure what I like best. About 5 hrs on my Carver Mini Simms so far.
@mario.crn_2 жыл бұрын
Thanks so much ur saving my life
@TheReal_DeanD3 жыл бұрын
Thanks so much for this vid mate. Super super helpful.
@ericbrammer22453 жыл бұрын
'size 14' wrench; 14mm, which almost equals a 9/16". Not to be too exacting, but as a Machinist, that was a tad too vague.
@laithsu Жыл бұрын
Hey Shane thanks for putting this great vid together. I just started riding my C7, and it's brand new. Do I have to grease it even though it's straight out of the box, or maybe I should wait till I've used it a bit more?
@joedees5563 жыл бұрын
can you do a Yow maintenance video? love the channel man thanks so much !
@WRandallHead Жыл бұрын
hey bro amazing video! One question though, how are you cleaning these? wiping the parts down or soaking them?
@shanelai2515 Жыл бұрын
Wiping is good enough
@Liamcourtnae4 жыл бұрын
Yoo i would love a tutorial on the wheels/bearings because im so stuck after my bearings exploded. Different trucks but im sure their similar surf trucks
@BrandonJones-jt8lj4 жыл бұрын
Can you do a video on how to assemble the truck on the Carver deck ?
@shanelai25154 жыл бұрын
Yep added that to my list
@JoshMuntz5 ай бұрын
Awesome video, cheers Shane. Anyone know where to get the C7 thrust bearing kit in Australia?
@Waverider4u Жыл бұрын
I have a feeling I need some grass for my nerves while disasembling and puting it back together 😂
@astridmenendez52893 жыл бұрын
Gracias!!
@mirkochyurlia2023 жыл бұрын
hi, I have a CARVER RESIN 31 skate with truck c7, and I am having a problem with the screw that tightens the spring. it comes loose all the time but too easily. I tried to disassemble the truck c7 and he cleaned the grease near the screw head (maybe he could make it easier to unscrew, like your advice) but it didn't help. after 30 minutes of skating I find myself with the screw completely released. what can I do? thank you
@guybartlett95873 жыл бұрын
I had the same problem,I just didn't grease the spring at all and problem was solved.
@anatolebone30734 жыл бұрын
Hi Shane, thanks for this tutorial. Could you let us know what is the grease you use? Cheers
@shanelai25154 жыл бұрын
Premium synthetic blend Lithium complex grease
@anatolebone30734 жыл бұрын
Thanks!
@WRandallHead Жыл бұрын
do you have a video for the rear truck? I can't figure out how to reassemble
@richardcartwright50194 жыл бұрын
Hey Shane. Can you add grease to the spring? i did this and now the tension bolt is becoming loose on it's own when pumping. I've made sure not to grease beyond mentioned in the vid.
@shanelai25154 жыл бұрын
Yes. Add marine grease for extra protection against moisture. Cover the whole surface of the spring. I had the same problem twice. Try cleaning all residual grease on the bolt head and in/around the hole. Also try not greasing around and into the spring nut. For me it was fine after that
@Tel--wg8te2 жыл бұрын
!!!! Very important place missed !!!! Link to link pin joint should be cleaned and greased well!
@omoleque11 ай бұрын
Hi hi the pivot got stuck a d I can’t release it to replace. Any video o technical help for this?
@SnwbrdB4 жыл бұрын
This was great. Any thought on how much time, miles, or other measure before this is recommended?
@shanelai25154 жыл бұрын
truck looseness is about preference. for longevity, i would suggest to check your truck atleast once a month. or more often specially if you like to ride very loose (the link might be rubbing against the walls and the spring bolt)
@solcobian Жыл бұрын
did you use something into the bushings?
@MrDreeyef2 жыл бұрын
hey shane i have a black coated pair of trucks will the acétone ruin the coating ?
@erdem.gurs0yy Жыл бұрын
dude is there any alternative as speed cream
@Mindrol.Lhakyi3 жыл бұрын
I cannot find the thrust bearings for this with exact specs from Carver.... Carver is sold out and has been for some time. My housing cracked.. I have all of the rollers but dont think it'll be safe? Help!! Lol
@julioluque62232 жыл бұрын
How oftenn do you apply lubricant?
@KortovElphame3 жыл бұрын
*this is why you get a Waterborne surf adapter*
@ruanstiga52734 жыл бұрын
How do I know if my spring is broken. Is it supposed to make any rattling noises when riding and hitting bumps or rocks
@shanelai25154 жыл бұрын
Most of the times, it is the bushings that are squeaking. Put a drop of oil on it. That should do. If your spring is broken, you won't get any rebound when you pump. Still, it is good from time to time to open the C7 system to check for wear. Sometimes the spring bolt is too loose, and so it vibrates freely as you move.
@mikeuptegrove2 жыл бұрын
Any part number for those thrust bearings?
@richardcartwright50194 жыл бұрын
Hi Shane. Im new to the world of Carver skateboards but loving it. I've noticed when i pump my front truck has developed a slight clicking sound. Have you come across this before buddy? Also me and my wife love the vids. Were both learning. Cheers Rich
@shanelai25154 жыл бұрын
Is the spring bolt loose ? Could be the link hitting the sides of the chamber. It's best to open the truck and see any unusual wear
@richardcartwright50194 жыл бұрын
@@shanelai2515 its brand new. Was told to try a tiny bit of oil lubricant on the bearings.
@shanelai25154 жыл бұрын
Did it work ?
@richardcartwright50194 жыл бұрын
hey @@shanelai2515. Yes it did. Just put a tiny amount in and the noise has gone.
@richardcartwright50194 жыл бұрын
@@shanelai2515 back again. Looks like i need to take it apart. It's annoying as I've only had it a few weeks.
@guysirois97983 жыл бұрын
Le C7 de la compagnie carver est identique au smoothstar front truck? Je pense que c’est un autre type de ressort qu’il y a chez carver. No?
@shanelai25153 жыл бұрын
C7 et smoothstar utilisent le ressort type compression.
@eversharpaudio87574 жыл бұрын
Do I need to add grease, I bought a new truck and I just assumed it would come ready to use (Carver trucks come with no info / instructions) I've only used it for two days but I'd hate to damage it, perhaps I should open it up and grease it?
@shanelai25154 жыл бұрын
Yes you should definitely grease (marine grease preferably). Cover all part of the spring. Avoid the bolt head and hole You may check them back fortnightly/ weekly for wear if you ride a lot
@garrettcirrincione32082 жыл бұрын
@@shanelai2515 can you use grease on the swing arm bearing? i noticed you used the bones for that part instead of grease
@andalingtanjung8835 Жыл бұрын
can the c7 be changed to cx by tightening it? if i tighten it is it safe for c7? or is it easy to loosen later?
@shanelai2515 Жыл бұрын
No matter how much you tighten the C7, it will never feel the same as a CX. The C7 will always feel more 'flowy' because it has a long arm. Also over-tightening the spring will cause it to lose its elasticity (springiness) over time.
@andalingtanjung8835 Жыл бұрын
@@shanelai2515 thank you 🙏🙏
@DimaYamubei4 жыл бұрын
If I make kingpin too loose, is there a possibility it falls down while skating?
@shanelai25154 жыл бұрын
Definitely. Always check your skateboard for any loose parts. As for me, i love my trucks as loose as possible but without them loosening by themselves with vibrations
@DimaYamubei4 жыл бұрын
@@shanelai2515 got it, how many turns from default settings is optimal in your opinion? From completely tight to fair loose?
@shanelai25154 жыл бұрын
@@DimaYamubei it's really up to your preference. I would go for loosest
@CzekoladaTrufla4 жыл бұрын
I had c7 for few months and it worked great. But lately whenever I drop the board looks like it is too loose and spring doesnt work. So I opened it and link covering spring jumped out from bolt. I put it on agine, adjusted so it si quite loose.but after every next shake it happens again. Nad spring bolt seems to be very loose and moving. Has anyone had similar problem?
@shanelai25154 жыл бұрын
First time i hear that. Is there any deformation?
@richardcartwright50194 жыл бұрын
How much grease is on the spring? I put way too much grease on the spring and after 30 minutes on my board the front would loosen. I could turn the spring bolt by hand. I've been having clicking sounds still coming from my front truck still. I think it's the bearing bolt? Got in touch with Carver and there trying to firgure it?
@yourmomsdildodrawer4 жыл бұрын
Just lost my spring tensioning bolt. Luckily it's only $6 and they offer free shipping right now.
@BrandonJones-jt8lj4 жыл бұрын
Do I loosen the back truck if it's too tight ?
@shanelai25154 жыл бұрын
Totally up to your preference
@BrandonJones-jt8lj4 жыл бұрын
Can I do anything of this trick's on any surface
@ericbrammer22453 жыл бұрын
Yup! And, consider your Bushings! You could (very inexpensively!) swap out a bushing or two, to a durometer that suits your riding style better! Look into these; Venom, Riptide, BloodOrange, Khiro or Bitch, or Jim-Z's. "PSR"