Catia V5 Tutorials|Part Design|Stiffener

[@howENGINEERSdoit]

Hi Alex, Thank you for your comment. Now coming to your doubt, For a stiffener to work, There should be only one opening for the profile you create, and the open end points of the profile should be coincident with the closing surfaces of the corresponding part. Go through the video again and keep this point in mind. Get back to me soon with the result. All the best.

[@MichaelJPanayi]

thank you, I was having trouble with this as my profile wasn't touching the body! Im learning Catia from scratch with only online tutorials so this was a great help :)

[@howENGINEERSdoit]

You are welcome Ashish..!! Keep watching..!!

[@davidgruty]

well... in the case of the cylinder one can make the tilted line of the sketch for the pad go a big higher and the pad will cover everything

[@CADmodel]

In the L-plate with the cylinder...I think one end point of the stiffener you have taken slightly inside the end of the cylinder.... Can we do the same by clicking one end point exactly at the end of the cylinder?

[@howENGINEERSdoit]

Hi Nitesh, The video on coupling is already available in my channel, Please take a closer look..!! I will include the link to the video under the description above for your convenience. Thank You

[@smlfrd]

Can't get this to work. I did EXACTLY as you showed in the video and I get "Feature Definition Error: The selected sketch contains several open profiles or some geometry used for construction. You must specify the construction geometry to solve the profile ambiguity." I didn't use construction lines or anything like that. I even tried it on new Parts to see if my model was the issue but evidently it is not. Please help? Thanks.

[@howENGINEERSdoit]

Good to know my tutorials are helping you..!! Subscribe me and get notified in your inbox every time I upload new tutorials..!! Enjoy..!!

[@howENGINEERSdoit]

Hi Anto, Surely I will upload more videos, Let me know for which topic you need the videos, If it doesn't exist in my uploads already, I will surely create and upload it. Best Regards.

[@Uthael_Kileanea]

Wait... You can still use the Pad command. Just make the sketch higher so it intersects with the cylinder... Anyway, thanks for the explanation. I couldn't figure it out by trial and error :)

[@faridtavakolmoghadam]

thanks for the video. I am doing the same thing that you did in the video but it doesn't work. the two open parts of the stiffener line was created using the 3D project and then removed the projected parts. when I try to run the command it says: topological operators: invalid profile body. what am I missing in this? Thank you in advance for the reply.

[@howENGINEERSdoit]

+Farid Tavakkolmoghaddam dear Farid, if you get such error, it means you have some overlapping sketch entities. In case of stiffener, make sure that the stiffener line touches the face of both the supports. Hope that answers your question.

[@mandalamukesh6486]

Mohammed Shakeel

[@cic6112]

Nice video there is no hatching for stiffner in when we draw cut section. Then why catia show hatching for stiffner in catia drafting???

[@antobiju3644]

Hi....Thank you Very Much. I am beginner for Catia......Can u Upload some more videos for basic......

[@jingjielim3634]

Hi, may I know how to deal with the isolated line. Because I face this problem when I was proceed after done the 2D sketch.

[@howENGINEERSdoit]

Hello, you need a closed loop to perform solid operations such as PAD. Check your sketch. Or there is an option to inspect sketch.

[@niteshkumarsharma8305]

Thank you Sir. can you upload video on coupling in multi-section solid defination.

[@saiganeshb746]

I have draw gear but I I tried pad option something went coming on dialogue box that like this at the sketch contents several open profiles are some geometry user for constants and you must specify the question geometry to solve the profile ambiguity

[@saiganeshb746]

Please tell me sir I trying number of times bu but error is coming

[@howENGINEERSdoit]

This is happening as your profile must be open and you are trying to do a feature like pad. Inorder to create a solid feature from the part workbench, your profile must be closed. Let me know if you still have doubts.

[@harisainathareddyeragam1822]

But sir the distance from baseline to angle line

[@sabirahmed1432]

Nice Video

[@ramanbhatnagar5684]

Hey... Its showing topological operator : invalid porfile body. What to do??

[@shivanshuudeniya3338]

same here

[@howENGINEERSdoit]

Hi Kowndinya, Please watch the video. Thank You.

[@akashdargad3449]

really helpful videos thanks..

[@msp3305]

vidio is not clear please sir aap achchhe se video banaya kuch samj me nahi aa rha h ki kaun sa button ka use kar rhe h aap

[@VinayKumar12921]

Hello Sir,,,Your Videos are Good,,I Need Auto Cad Software,,,From Where i can download it ?

[@howENGINEERSdoit]

Gratitude..!!..my pleasure..!! I think you can download a student version from Autodesk.

[@vaidhyanathan.s9921]

My doubt clear , thank u bro (pad and stiff)

[@wolkantoros]

Thank you so much , I just did my part of this command ( so useful tutorial )

[@howENGINEERSdoit]

Wolkan Toros You are welcome..!!Please share in your wall and among your friends..!!

[@ilduaragonzalezalvarez4932]

Thank you! Really useful :)

[@kitrakkitru8518]

Guruji thanks for the knowledge

[@theengineerbaba]

thanks you sir your tutorials was osm #Theengineerbaba

[@shashankmalpure1455]

Very Useful...

[@write2sijovarghese]

Amazing tutorials :D

[@saiganeshb746]

Small problem sir can you please respond

[@howENGINEERSdoit]

Yes sir?

[@saiganeshb746]

If you don't mind give me your WhatsApp number I will show you my problem by picture

thank from Spain

[@howENGINEERSdoit]

Hello Javier, Stay tuned for more videos. Where are you working and which domain?

[@write2sijovarghese]

Nice work :)

[@howENGINEERSdoit]

teşekkürler..!! Allah bu hayatta ve cennette mutluluk ve refah ile hepimiz korusun

[@howENGINEERSdoit]

JazakAllah, Thank you for your notice. Assalamu alaikum Varahmatullahivabarakathu

[@tia1103]

quick and simple !

[@howENGINEERSdoit]

Hi Friend, I'm sorry for the late reply. Sure, its [e-mail]. Thank you for writing to me.

[@mohammedzafeer]

Assalaamualikum this vedio would be wonderful if it had a good Sound,

[@tranvanduong01]

thank you for yourshare.

[@Manikanta-vt7pr]

Thank u for this video i want you that clearly every module with a each command and how to use that command for all catia V5 R20 please provide me that videos thank u again

[@howENGINEERSdoit]

Thank You..!!

[@ashishsharma4296]

thank you sir....

[@gfberen34]

ALLAH senden razı olsun.

[@hanger687]

nic

[@FadeToBlack86umit]

thanks bro.

[@sambit_praharaj]

you are not audible clearly.

[@SatendrayadavdangerraosaabSKya]

This is a fack