Stator Rewinding angle grinder

[@robertooliveira9316]

Top de mas bobinei a minha mas foi passando volta por volta no campo deu trabalho mas tá top mas desse forma e bem mas tranquilo detalhe em uma pequena lixadeira e prático desse jeito que vc fez numa grande então nen se fala parabéns Deus abençoe.

[@alanborromeo8854]

Idol how many tuns , what is the arrangement, clock wise and counter clock wise? No need of applying Electric Varnish? ?

[@bosconazareth9066]

Nicely rewinding and a good video,bravo 👌👍

[@irishguy200007]

Would this stator produce a strong North and south pole and can it be tested with a piece of steel once energised?

[@edwintiquia6613]

Gud morning idol prof.tnxs alot for teaching us how to rewind a defective coil. U gave me a lot of knowledge about it.take care always en GODBLESS us all...

[@junuayan3374]

Mabuhay ka bossing sana all ang galing ng talento mo hanga ako sa skills mo

[@karmawalaelectric4988]

Very nice full video very nice Information video bro👍👍👍👍👍👍👍👍👍👍👍👍👍❤❤❤❤

[@harunraza9192]

Sub haan Allah very good field shukriya bhai harun machine tools

[@guillecamacho5836]

Buen trabajo👌👍👏

[@vijaykumarmahto7384]

Bhaya chaar lead me se do lead me ring jaisa kya lagaye plz reply

[@ManoloDiazMartell-q8r]

Buen trabajo amigo

[@zahidabbasi5614]

Excellent video good job.thaks sir. [PAKISTAN]

[@norbertovisca8782]

, sir, connection, and termenal, tutorial 😊👍

[@AmtzTech]

Good video 👍

[@utkanwar6895]

A apne ye angle grinder kaise banana dhanywad

[@AlaHenPer]

you didn't try the stator, work or not?

[@zakhu4971]

hello from ueaq with you well done tell me how to wiring wending after finish

[@JohnTechnoPh]

Ayos bro keep on going.. new ka tech po

[@rafaelsanchez325]

Me gusto El trabajo ya lo e practicado yo

[@reynaldoubiracicasalunga]

Bom dia O principal não foi mostrado como tomar as dimensões da forma? Abraco

[@songslover7599]

Nyc😍😍😍😍

[@iraqresitance9663]

Hello from iraq well done helpfull

[@viswanathanramakrishnan7613]

How you have calculated the number of turns per winding. I wish to learn from you. Otherwise all the other parameters are noted by me from the video which was an educative one to me. Thanks for a nice video presentation. Also kindly post a video on armature winding.

[@realfamilyman]

He showed how at 2m08s to 2m15s (but didn't actually do it). i.e. After cutting out the burnt coils you count the strands manually. The number of turns plus the wire thickness as measured on the wire gauge tool is how you make new coils the same turns/power as the old ones. (And one or two turns counted too many or too few isn't going to make much difference.) Then later when winding the new coil, you turn the handle the same number of times as you counted. What he didn't show but should have, is how he sized the block of wood he wound the new wire around, so the new coils were the same size as the originals. He probably just measured the height of the transformer for the vertical length, then the width where the coils poke out to 'turn' at one end. But he still should have shown it.

[@robbirobson7330]

@@realfamilyman i have a question, it seems it does not matter that the wires are perfectly aligned like they are in a transformer?

[@realfamilyman]

@@robbirobson7330 If you mean how he lets the wire fall randomly wherever it likes, rather than carefully winding each turn nice and neat... then any final difference in output would be negligible (as long as the coils are all wound in the same direction which they obviously are). i.e. The magnetic field cuts across each coil of wire, individually, but all at the same time. Thus it's like having a long length of coiled copper tubing, with a water inlet tapped into the start of each new turn of the coil, then turning a water tap on and off quickly in pulses - which effectively "pushes" any voltage/current made through each coil, all in the same direction, all in the same instant of time. So if for example the repair was for a ceiling fan, and he wound each coil carefully and neatly like a computerised machine would do, he might get a slightly faster top speed out of each speed setting. Or if it was for a wind generator, he might get a slightly higher voltage/current output. So unless you're rewinding some kind of industrial machinery with thick wire and creating hundreds of amps... then painstakingly winding each coil neatly wouldn't be worth the tiny amount of speed/power gain.

[@robbirobson7330]

@@realfamilyman thanks for the answer, i tried to rewire a transformer once and it was very difficult by hand and in the end i did not get the same output thats why i asked and now i also want to make my own wind turbine and i also need to repair a small angle grinder which coils has burned

[@boybravo689]

@@realfamilyman thats my question sir how he can arrive the size of wooden bobbin that make him used to make a stator coil sir

[@technicianbro86]

Wao nice work . good job bro

[@tsetse7120]

What happens if you scrape the coating on one or two of the turns???

[@khanjeeseller9746]

Nice work bro 👍

[@AynaeChitral]

Nice idea very good

[@abhinavcp_]

Which glue did you use?

[@vittalkoppal]

Can you please provide me with link to buy winding machine? 🤔

[@primitivomartinezjr8502]

Idol pwede sa susunod rewinding nman ng electricfan salamat

[@pubgmlgamer0764]

pls idol

[@alfredoperez7667]

BUEN DIA! HERMANO SI TODABIA ESTA AHI LO FELICITO Y LE PIDO SI PUEDE DECIRME LA DIMENCION O TAMAÑO DE LA PIEZA DE MADERA LE AGRADESCO DESDE BACHAQUERO ZULIA VENEZUELA

[@alexanderguyo423]

Good video Bro. Thanks

[@ramratan4460]

Nice tape, chipkane ka name batana Sir

[@pilotboy2612]

How are the wires connected to the supply?

[@tommythorne8252]

I learn lot what show thank you

[@meggamaurice7408]

Good old fashion way of winding a field coil

[@winstonclarke9221]

Was it heat shrink that you use, after you join the wire together,

[@osbornlacerda2770]

Its 'wire sheath' , it's just left over the wire and not shrunk around it . Material : nylon or fiberglass. It's used to protect the copper wire from the vibration [it receives from the plastic (edges)],and from UV (sparking at the armature carbon brushes contact. This kind of reinforcement is used mostly in $30 and above angle grinders.

[@ravenolds6549]

Nice job sir ask ko lng din ano tawag sa tela na Ginamit mo at saan nkkabili ynx

[@katkatulnagan]

request ko na magconduct ka ng training sir...

[@ribertsole]

Como lo enrollas

[@michaellabastida5642]

ang galing mo talaga sir saludo ako sayo

[@cdltek]

thank you sir.

[@edilbertoordonez1255]

Cuánto cuesta una máquina de esas

[@Leandro-tv8sb]

Boss may nabibili ba na winding per model ng stator?

[@abhijithabhijith284]

how you take the winding bobing measurement

[@munawarhussain4577]

Sir winding ap ney theek ke hay. Mager Ap goungey hain. Ap ney aik bar be Nahi Bola ye wire kon ci hay

[@geraldinepequete936]

ayos yan sir pwede qna i rewind un nasunog n grinderq

[@MuhammadQasim-dq2tz]

Kindly ye b btaye k single phase 2kw k generator me starting winding q hoti hai, jbke wo capacitor type hai. Or rotor diode wala.?

[@lorenzoj.agapito5536]

Nice job sir. Galing. ...pa pm adress mo sir. Pde ipaship ang item?

[@tytaseroda9075]

How many turns did you make?

[@fareastideas244]

Pag ka ganyan bibilangin mo ba ulit yan?

[@alexandresouza9942]

Nice job.

[@العطوانيباسم-ن9ه]

عمل رائع انت تستحق عشرة على عشرة

[@tommythorne8252]

Very good

[@debasischakraborty2169]

Recently my angle grinder field burnt , i try. but my field is mould by nylon connector please tell me the way.

[@zahidabbasi5614]

Very good excellent video please keep camera on slow motion.thanks [PAKISTAN]

[@rueldiano4456]

New subscriber sir paano ba makabili ng rewinding machine...pedi ba makabili SA mga nagawa mong drill at grinder.

[@ribertsole]

Buen trabajo

[@munawarhussain4577]

Very nice method

[@arnoldparedes5460]

may nabibili po bang ring wire para sa kabitan ng carbon, ano po tawag don? salamat po

[@antoniomarcosnobre8622]

Massa muito 👍👏👏

[@jvlongakit25]

Naalala ko yan mag manual rewind ung college days ko

[@reynaldoubiracicasalunga]

Faltou mostrar as dimensões da forma da bobina para enrolar Grato

[@teguhprasetyo3661]

keren Bro

[@talwinderbhatia8998]

Old field ki turn kitni thii

[@boybravo689]

Sir ask ko lng paano mo nacompute ung size ng bobbin new subscriber mo ako tnx

[@k.s.kvlogs8844]

How many turn bro

[@cdltek]

160 turns both side.

[@narenderverma4203]

Thanks for nice job

[@Gamay_43tv]

Mga ilang ikot boss thanks for

[@cdltek]

160 + 160 = 320

[@angelmarinoizquierdocampov1781]

Donde tienen el taller, la dirección

[@ryc4803]

What is the machine name????

[@ravenolds6549]

Nice job sir ask ko lng din ilang turn ba ang field coil ng circular saw, salamat

[@natesananandan1464]

Aremature winding for the same angle grinding machine method present please

[@rosemaris22]

Sir ano po yan tape na puti?

[@primitivomartinezjr8502]

Idol gusto ko sa malaman kng ilan ikot sa bawat winding na ginagawa mo idol salamat

[@khenjingaming868]

Anung size nung kahoy lods please respond po slmat

[@talwinderbhatia8998]

Coil turn ??????

[@juanfranciscoevangelista7656]

Me gusta embobinar Quiero aprender a embobinar el rotor de pulidora

[@Techcommunity360]

What is the number of the winding

[@cdltek]

160 turns both side.

[@bhaveshpithadia4465]

शुप्पप फिटींग लेकिन सर पूरानी कोईल को कैसे पता करे ओपन है या नहीं

[@geraldinepequete936]

pwede ba pansapin ang lace paper sir

[@diytechspirit914]

Good video but the music man. There is so much NCS songs so there is no need to play the same song over and over and over and over again.

[@bibhaspramanik6887]

What is the coil turn

[@direndirenis7740]

​@@bibhaspramanik6887 bir hh ne zamanhhh

[@thesneh6873]

Of what metal the stator is made tin or iron plz reply

[@Dave_en]

Iron mixed with silicon to increase relative permeability. Otherwise pure iron sheets may heat up when being magnetized by alternating current leading to more power loss due to iron. You can say it as silicon steel.

[@thesneh6873]

@@Dave_en Can we apply isulating varnish to iron sheet.

[@Dave_en]

@@thesneh6873 yes, but it should be silicon steel for this purpose. Not ordinary steel.

[@thesneh6873]

@@Dave_en Ok so you tell me whete I can find these silicon steel

[@Dave_en]

@@thesneh6873 from electric motor spare parts store. You can ask for "stampings" or stator. You have to specify the purpose so that they can help you finding the suitable material. For mixer grinder, exhaust fan, ceiling fan, transformer etc. We have a huge market for electrical goods in New Delhi. You can find similar place at your location.

[@koJIRH]

good job

[@romeolabarda1421]

Nice one..thank you.

[@carlitstv11]

Sir saan mo na bili yang manual rewinder mo?

[@cdltek]

Sa Lazada o sa raon

[@diysarisariworks642]

Pede ba magparewind sayo stator sir? Magkano para sa angle grinder stator gws 6-100?locatiin nyo sir?

[@markguibo3611]

Lahat ba ng grinder at handrill stator boss parehas lng ang sukat NG winding??

[@joelvalencia2721]

Magkaiba po yan ,magkaiba din halos ng biglang yan

[@jimmygaela8313]

Location pls.

[@cdltek]

Dasmarinas cavite

[@romellaurel974]

Sir ilang turns po ang coil nyan sir.

[@edvaldofranciscodasilvafra3553]

Muito bem gostei 👍

[@viswanathaniyer2372]

good video

[@ekhles104]

very excellent

[@severinadaguiasilvia6300]

Eu não sei traduzir não tenho esse disco de medir o fio ara saber a espessura e quantas voltas eu tenho que dar

[@meuterritorio]

Usa um micrômetro. Procura tabela de conversão de milímetro para awg.

[@toaderviciriuc6944]

Ok felicitari

[@fareastideas244]

Ano po tawag sa tela na nilagay nyo?

[@AdemirSoares294]

Muito bom parabéns

[@EgyptCanada]

👍👌🙏

[@FelinoAnticomunista]

Buen video pero música estresante. Lo vi en mute

[@edibertobabaran135]

sir ilang ikot b yan sana sinabi m n din.

[@bolamick3278]

Show de bola

[@markfrancisco5299]

boss ilan bilang ng ikot yan pagrewind?

[@ashokpatekar21]

KITNA TURN HAI YE NAHI DIKHAYA HAI,, YA NA BOLDIYA HAI,, YE VDO PARIPURN NAHI HAI,,