Making a simple table saw / Homemade table saw part 1

Hello friends. In this video, I shared a simple bench saw construction. I showed you how to make a bench saw from a circular saw. I have shown this work as plainly and simply as possible. The bench saw is a must-have machine in the wood hobby workshop. A bench saw that doesn't cost much with a circular saw. I uploaded the video with the title making a simple table saw, homemade table saw part 1. I used pine wood for the frame and parallel guide of the bench saw. I made the top table from 1.8 cm mdf. I used quick glue and coolant spray to install the legs of the bench. I used a 21cm wide horizontal transition clamp in the construction of the bench guide. This horizontal toggle clamp has been really solid on the bench guide. In bench saws, the one-sided guide is actually not very sturdy. But with this clamp, the compression was very, very firm. I shared all the measurements at the end of the video. As I mentioned above, I finished the bench saw, which is widely used in woodworking and wood hobby, in a simple way and shared it with you. I hope you like my homemade table saw, table saw diy, making table saw, circular saw table, table saw guide. Thank you very much for your interest. Thanks for watching. Stay healthy.

[@michaelmannucci8585]

I love when people show how to build a table saw and you need a table saw to build it... that is SUPER helpful.

[@mrdashin8323]

All those cuts can be done with a hand saw, or skil saw.

[@rakanal.2925]

Ikr 😂

[@SidiusD]

Well technically he didn’t…he made the table legs with the Table saw, the actual table top where the saw goes was built merely using the circular saw and a plunge router I think. So theoretically you could build that first then prop that piece up to build the rest of the table. He should have done that in the video and completely avoid using his actual table saw 😅

[@maystroyep5416]

If you cut the wood with your hand 👌🏻 so do it or use a knife 🔪😂

[@daniloalves1420]

​@@mrdashin8323 Piorou mais ainda sua resposta. Ter a serra própria. Kkkk

[@muratozturk637]

bir an yabancı kanal sandım meğer kardeşim Türkmüş kıvanç duydum çok başarılı zekice işler yapıyorsun tebrik ediyorum Allah azmini yüceltsin

[@woodworks3585]

It would be nice to see someone make a table saw without using a table saw and fancy equipment for people who don't have them. There are thousands out there who don't have the tools and just want to make a start at woodworking. 👍👍. The table saw turned out great though.

[@williammarum8524]

Made one of these in 1977, 18yrs old then, had it for many years and it worked well, made it with a Makita 71/4" skill saw plenty of power. Great idea for anyone who cant afford a descent table saw

[@CelalUnal1]

Thank you so much.

[@canacuner4141]

hemen herkezin yapabileceği basitlikte harika bir kesim masası herkeze iyi örnek oldunuz en kısa zamanda daha iyisini yapabileceğim fikri uyandı bende .teşekkürler

[@НатальяШарапова-в4т]

Самый простой вариант и главное все понятно для таких как я! Буду делать такой!!! Спасибо

[@CelalUnal1]

Спасибо. Я рад что тебе понравилось.

[@luisfernandomendez3029]

Soy evanista hace muchos años me gusta ver este canal y alaves saludos a todos aquellos evanistas que ven este canal aqui desde costa rica

[@CelalUnal1]

Muchas gracias. Me alegro que te haya gustado.

[@juanlongoria5050]

Oh okay, muy buen invento señor carpintero. A muchos aprendices como yo, nos haz motivado a fabricar muebles sencillos , no como tu los haces pero parecidos. Muchas gracias por compartir tu gran habilidad de carpintero.

[@CelalUnal1]

Muchas gracias. Me alegro que te haya gustado.🙌🙌🙌😊

[@mustafaemad1140]

The simplest and best video I've seen. For more than a month, I have been following Arab and foreign KZbinrs in this regard on how to make a table for a disc saw, but I did not find anything like what I did. You are a genius your follower from Iraq 🇮🇶🇮🇶🇮🇶💪

[@CelalUnal1]

Thank you so much. I am so glad you liked it.

[@mustafaemad1140]

@@CelalUnal1 🌹❤️❤️🇮🇶💪

[@gurbuzhome6311]

Celal kardeşim çok pratik, işlevsel ve çok güzel bir çalışma. eline yüreğine sağlık. Paylaştığın için teşekkürler.

[@CelalUnal1]

Çok teşekkür ederim. Beğendiğine çok sevindim.

[@mhamedlaidioui7582]

Merci beaucoup pour cette vidéo mon ami le résultat est au top comme toujours c’est un plaisir d’apprendre avec toi bon courage et à bientôt mon ami 👍🙏👍

[@CelalUnal1]

Merci beaucoup. Je suis tellement contente que ça te plaise. 😊😊🙌🙌🙌

[@pasaje1790]

Qué buena mesa, nunca había visto una así de sencilla y funcional; haré la mía. Gracias por compartir sus conocimientos. Felicidades y saludos

[@CelalUnal1]

Muchas gracias. Me alegro que te haya gustado.

[@MARCELLO6859]

Really simple, precise and effective. Congratulations, well done.👍

[@CelalUnal1]

Thank you so much. I am so glad you liked it.

[@AgustinL.Farkalitsch]

Mesa simple, económica y prolija. ¡Maravilloso trabajo Celal! Felicitaciones y saludos desde Argentina. 🇦🇷

[@Sergo13rus]

Этим летом обязательно такую же собрать,отличная работа !!!

[@CelalUnal1]

Спасибо за просмотр.

[@michaelconover2179]

Great video!!!! You are showing people like myself how to start out in wood working without having a lot of money. Most of the reviews I could read sounded like people who have a lot of money and big shops for their tools. You do awesome videos and keep them coming!!! There are people in this world full of hate if they didn't come up with the ideal themselves. I am going to build this one since I don't have the money for a real table saw. Looks great and works and that's all I need to get started.

[@CelalUnal1]

Thank you so much. I am so glad you liked it.

[@Чебунок]

Чтобы сделать циркулярку, нужна другая циркулярка, гениально

[@ДядяВася-ю2с]

И фрезер, и какой-то шустрый клей, и аэрозоль к этому клею... А наши на коленке, на глазок делают из всякого барахла и нисколько не хуже. Левши-с однако и Кулибины!

[@eduardparshin145]

Смотрю твои ролики по столярному делу, очень нравится и главное из простых материалов такие хорошие изделия делаешь. Хочу так же научиться. Продолжай в том же духе. Мне нравиться, то что ты показываешь как делать, без лишних слов. Спасибо за труд!

[@CelalUnal1]

Спасибо. Я рад что тебе понравилось.🙌🙌🙌🙌😊

[@GuillermoRodriguez-ws5tc]

Muy ingenioso para hacer la sierra , de paso felicitarle por enseñar , un don que nace de la persona con voluntad de ayudar a la gente . Saludos desde Cali Colombia .

[@CelalUnal1]

Muchas gracias. Me alegra que te guste. Saludos desde Turquía.

[@Ahmed-sq5fz]

This is the best video showing how build a table saw ever.

[@CelalUnal1]

Thank you very much. I am so glad you liked it.

[@larsooo152]

You need a table saw to build a table saw. Perfect 😅

[@CelalUnal1]

Thank you. I am so glad you liked it.😊🙏

[@stoffel6348]

My first thought exactly 😂

[@jimetal367]

Ahora vamos convertir una cierra de banco en una sierra circular. 😂 Solo bromeó. Buen video.

[@marciliodonizzet9587]

MATEUS ​@@CelalUnal1

[@pierreduloup7543]

😅😂

[@neliorodrigues2249]

Muito bacana ficou excelente seu projeto serra de bancada foi uma ótima apresentação e muito boa à demonstração valeu obrigadao

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

[@KT-fi7tm]

Step 1: buy a table saw to make cuts for the base of your table saw

[@qazqaz6939]

😂

[@thato3274]

😂😂

[@navb757]

😂😂😂😂😂🤣🤣

[@David-xq7ef]

Exactly what I was thinking...

[@nuribulentozer3204]

Çok kaliteli bir çekim, ayrıca çok kolay anlatılmış. Çok teşekkür ederim.

[@CelalUnal1]

Çok teşekkür ederim. Beğendiğine çok sevindim.

[@vicsar3606]

Видео данного автора приятно смотреть и создают положительные эмоции. Здоровья Вам и творческих успехов

[@CelalUnal1]

Спасибо. Я рад что тебе понравилось.

[@emersonforattini]

O melhor vídeo, muito didático.. Parabéns, excelente trabalho.. 🙌

[@CelalUnal1]

Muito obrigado.

[@PauloSergioA_Medeiros]

Perfeito trabalho meu amigo! Irei fazer uma pra mim com essas medidas. Obrigado e que Deus o abençoe 🙏🏻

[@CelalUnal1]

Muito obrigado.

[@многознаешьПлохоспишь-э1ш]

Что бы сделать циркулярный стол, нужен циркулярный стол! У меня все!

[@МестныйЖитель-ъ6щ]

Хорошо,когда оратор краток👍👍

[@by_talik]

тоже хотел это сказать :)

[@АндрейВирятинский]

с языка снял!!!

[@ale-ksej]

Необьязательно,главное столешницу с точньlми углами и прямьlми паралелями заказать а далее уже самому

[@amranwer1041]

انته تافه

[@ЮрийБереза-ъ5м]

Умничка, спасибо огромное что показал как можно быстрее сделать этот стол.

[@CelalUnal1]

Спасибо. Я так рада, что тебе понравилось.🙏

[@joas.pereira]

A melhor bancada caseira que já vi. Parabens

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

[@cinferfk]

Você tá de parabéns, muito profissionalismo, aprendi muito aqui neste vídeo.

[@CelalUnal1]

Muito obrigado.

[@tusharg21tube]

This is an amazing construction! Thank you for the video.

[@CelalUnal1]

Thank you so much.

[@selcukay]

Çok kullanışlı bir tezgah testere oldu dayama mastarı pratik ve akıllıca düşünülmüş eline sağlık kardeşim 👏👏👏

[@CelalUnal1]

Çok teşekkür ederim. Beğendiğine çok sevindim. Sağlıcakla kal ustam selamlar

[@carlosrodas2582]

excelente trabajo, excelente diseño fácil para hacerlo en casa,por supuesto con todas las precauciones necesarias para evitar posibles accidentes, todo con precaución y seriedad es funcional para hacer muchas cosas en casa,¡!!!felicitaciones!!!!para el qué trazó ése diseño, todo con precaución es y será una mesa de trabajo excelente para hacer cortes presisos.

[@CelalUnal1]

Muchas gracias. Estoy contento de que te gusto.

[@Neo-RSA007]

Ahhh a good ol'video of making a table saw and the first thing you see is the person using a table saw to make a table saw. this is so Table Sawring

[@manoelbarbosa480]

Pode acreditar. Seu vídeo é muito mas muito bem elaborado e de fácil entendimento. Parabéns pelo projeto.

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

[@irineudeganutti4154]

Parabéns muito bom mesmo, facilita bastante o trabalho do marceneiro.

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

[@dragoljubstamenkovic9585]

wow, a great tool for beginners. You probably started that way too. The only thing I would suggest is to upgrade the riving knife for greater safety for the one who uses this tool. Otherwise, I really like how you made the saw stand as well as the final processing.Thanks on behalf of all of us who watched this clip of yours.

[@CelalUnal1]

Thank you very much my dear friend. I am so glad you liked it. You're right, it has its shortcomings. I will make your sleds in the next video. This bench should not be used without an apparatus. It should be used consciously and carefully in every way. Thanks again for your nice comment my dear friend. Stay healthy.

[@JoseTorres-ze2ed]

Cómo se llama la palanca de opresión para la regla móvil , y dónde se consigue ?

[@藤原美明-z2z]

ふじわら

[@raulpavez7180]

muy buen video genial la mesa saludos desde mendoza argentina

[@CelalUnal1]

Muchas gracias. Me alegra que te guste. Saludos desde Turquía.

[@MEmarcenaria]

Ficou muito show meu amigo 👍👍 parabéns 👏👏.🇧🇷🇧🇷🇧🇷

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

[@BigD0na1d]

What a very professional looking job...well done! I would only say that the back of the fence should hook into the table so there is stability on the back end of the fence. Other than that its just a beautiful make shift table saw setup!

[@CelalUnal1]

Thank you so much. I am so glad you liked it.

[@lsneiva]

Ficou ótima! Excelente trabalho...

[@CelalUnal1]

Muito obrigado.

[@Oner_Kurukuz]

Gayet basit ve güzel olmuş. Eline sağlık.

[@CelalUnal1]

Çok teşekkür ederim. Beğendiğine çok sevindim.

[@juanmoralesvazquez3649]

Muchas gracias por su enseñanza y que Dios te bendiga hoy y siempre ♥️♥️♥️ y un fuerte abrazo desde Villagrán Guanajuato México

[@CelalUnal1]

Muchas gracias. Me alegro que te haya gustado.

[@Мастеримиздревесины]

Спасибо за видео, полезно. Как раз искал как параллельный упор сделать.

[@CelalUnal1]

Спасибо. Я рад что тебе понравилось.

[@izada666]

Тут упор сильно хиленький. Автор нормально не показывает прочность, он пытается гнуть брус, а не показывает его изгиб. Да и результаты измерения у него ±2мм. Если повторять, то упор должен фиксироваться с обоих концов, иначе возможно смещение при пиление твёрдого материала.

[@ale-ksej]

Упор нужнг в паззаводить и то точности не будет и дальная часть упора будет отходить.В бьlтовьlх, полупрофесиональньlх циркулярньlх пилах механизм зажима далней точки линейки происходит

[@rocknrolla4756]

Да ты парень молодец. Изготовление пилы при помощи пилы. Выше всяких похвал.

[@CelalUnal1]

Большое спасибо. Я так рада, что тебе понравилось.

[@wernerpobletemorales7728]

Excelente! Muy bien diseño, simple y funcional. Felicitaciones

[@CelalUnal1]

Muchas gracias. Me alegro que te haya gustado.

[@CesarMontanez-wh7ou]

El mejor video de KZbin, excelente. Bien explicado, gracias por enseñar las medidas. Gracias por el vídeo.

[@CelalUnal1]

Gracias. Me alegra que te guste.🙏🙏

[@landerdossantosferreira8018]

Perfeito, uma das melhores que já vi. Parabéns!

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

[@DarcilioKreitlow]

Simples e fácil, a melhor que já vi

[@CelalUnal1]

Muito obrigado.

[@sergeysokol5652]

Good table ! Question: do you need remove/install the saw every time when you need to change angle of the disk ?

[@CelalUnal1]

Thank you. The circular saw has a clamping ratchet and a bevel latch. It's easy to change.

[@wimvangeyt3866]

@@CelalUnal1 Nice table saw and simple to make, but I would remove the peace between the two slots so you do not need to replace the saw everytime ;)

[@orlandosilva4481]

Belíssimo trabalho. Bancada simples e de eficiência inegável. Só queria saber o nome daquele modelo de grampo que foi usado. Parabéns!!

[@ivamoliveira]

Se não encontrou ainda, se chama Grampo de Aperto Rápido Vertical

[@suleymancelik5027]

Elinize sağlık çok güzel olmuş bende böyle bir tezgah yapıp hobi amaçlı birşeyler yamayı istiyorum

[@CelalUnal1]

Çok teşekkür ederim.

[@Alesei_Gordienko]

Просто и гениально!!! Посмотрел несколько ваших видео, очень впечатлен! Подписался

[@CelalUnal1]

Спасибо. Я рад что тебе понравилось.

[@edifreitas225]

Celal, como já disseram nos comentários este seu vídeo é um dos mais didático e detalhado que já assisti sobre a criação de uma bancada para uso com Serra circular. Parabéns e gratidão por compartilhar este EXCELENTE vídeo aula.

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

[@JoseMorales-oh3dt]

buenicima

[@JoseMorales-oh3dt]

buenisimo

[@deniseclementinoguedes-rt3xl]

Você pre isa comprar uma serra de bancada para fazer uma serra de bancada.

[@Eletrojvb]

belo trabalho, parabéns

[@CelalUnal1]

Muito obrigado . Estou tão feliz que você gostou.

[@kaanisak699]

Ellerinize sağlık, çok yararlı bir video olmus, benim de yapmam gerekiyor tezgah. 7. Dakikada taktığınız aparatın özel bir ismi var mı?

[@CelalUnal1]

Çok teşekkür ederim. Yatay geçiş kelepçesi.

[@fethiusma4188]

فنان بأتم معنى الكلمة ، أنا من متابعيك ، 👏👏👏💯👌👌👌👍

[@CelalUnal1]

شكرا لمشاهدتكم.

[@barzankhoshnam5969]

❤God, I am very happy with your clean way of thinking and work

[@CelalUnal1]

Thank you very much. I'm so glad you liked it.🙏

[@ПоделкиИзДерева-т3ш]

Спасибо,что делитесь мастерством и знаниями! Очень помогаете ,особенно начинающим!👍👍👍🔥🔥🔥

[@CelalUnal1]

Спасибо. Я рад что тебе понравилось.

[@diy9301]

@@CelalUnal1 всеконешно интересно для диванных а вот скажите зачем такое городить когда есть хороший распиловочный стол? И другой вопрос как такое сделать с помощью нажевки, доски и куска фанеры? А не с помощью хорошего инструмента! Ведь кому нужен такой простой стол врятли имеет весь этот инструмент?!

[@ManFromTheStreet]

@@diy9301 вас смущает, что человек сделал доступный и хороший вариант, те что есть инструменты, вполне подойдут для реализации проекта, а что нет, всегда есть, чем заменить Или смущает количество подписчиков на вашем канали и его? И решили так его унизить? Зачем тогда вообще нужен ютьюб, когда всё можно купить

[@fernandocesardeoliveira7211]

Espetacular! Parabéns 👏👏👏👏👏

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

Emeğine sağlık Celal çok profesyonel gidiyordun bu video tam bizim gibi amatörlere hitap etmiş😀 kazasız belasız çalışmalar.

[@CelalUnal1]

😊Çok teşekkür ederim. Beğendiğine çok sevindim. Sağlıcakla kal ustam

[@asnanyuara5891]

@@CelalUnal1 ระดับทน

[@jeanmarcmeynet6005]

alors là chapeau avec pas grand chose une superbe idée utile pour ceux qui n’ont pas les moyens d’acheter une scie sous table encore bravo et merci pour cette vidéo 👍

[@CelalUnal1]

Merci beaucoup.

[@manueloval198]

Diseño sencillo, práctico, bonito y bien explicado! 👍🏼👍🏼👍🏼

[@CelalUnal1]

Muchas gracias. Me alegro que te haya gustado.

[@alpsinan]

The moral of this video: If you have an expensive table saw, a big planer and an extra circular saw that you want to sacrifice, you can make a cheap table saw to show off.

[@dayatamawijayaabadi6812]

Lol

[@ricardoortega6533]

Para los que no tenemos una sierra mesa podemos hacer una excelente video algo que usted no a hecho

[@walterjoseramosguillen2099]

​

[@sudimarno7159]

Yg buat ngubci pres apa namanya

[@Ro2_Mi]

And make the video so simple & short that you don't have to explain/ disclose how you switch the blade from 90° to 45° 😅😅

[@lucianapaivalucy6319]

Perfeito e muito bem explicado ☺️ 👏

[@CelalUnal1]

Obrigada. Estou tão feliz que você gostou.😊🙏

[@jecivalfagundes6785]

Excelente trabalho muito bom ficou top parabéns👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

[@muslimandproudofme8671]

Well done, creative person, and the explanation of the measurements was very nice

[@CelalUnal1]

Thank you very much.

[@ramazanbalaban4668]

Çok güzel oldu. Ellerine, emeğine sağlık, En kullanışlı ev yapımı tezgah testere.

[@CelalUnal1]

Çok teşekkür ederim. Beğendiğine çok sevindim

[@BrunoGomes-cc4ek]

Perfeito, trabalho incrível!!! Vou utilizar sua idéia, muito brigado por compartilhar!!

[@youtukang]

Salam 🤝🇮🇩

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

[@ЛешийВетер]

Чтобы сделать распиловочный станок нужен распиловочный станок 😂😂😂 Зовите доктора DIY и расходимся...

[@tumelo3703]

Hi buddy thank you so much for this video I have an extra saw laying around and I've been thinking on how I could do something like this... thank you again for this video it really cleared things up....any suggestions on how I could install a riving knife on it

[@CelalUnal1]

Thank you so much. I am so glad you liked it.

[@関賢慈]

これ台のこ

[@ВячеславПупынин-ъ6и]

Спасибо за прекрасно выполненное видио. Постараюсь учесть все советы при изготовлении своего стола.

[@CelalUnal1]

Спасибо. Я рад что тебе понравилось.

[@fatihunal4013]

Usta adamın hali bir başka oluyo 👏👏

[@CelalUnal1]

Çok teşekkür ederim.😊😊🙏🙏

[@layrtonsilvasoares4016]

Trabalho excepcional, parabens e gratidão por compartilhar irmão!!!

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

[@MrValldery]

Olá, meu nome é Valderi Silva. Sou do Brasil. Meu desejo recente, é construir uma bancada dessas, para adaptar a minha serra circular que comprei a poucos dias. Não entendo muito de marcenaria, apenas de serrelharia. Por isso, estou constantemente buscando projetos no youtube. De todos que busquei, o seu foi um dos mais simples e intuitivo que achei. O fato de você oferecer as medidas para nós, foi um ato de extrema camaradagem. Gratidão! Estamos muito honrados com o presente. Vou tentar usar o seu projeto.🇧🇷

[@CelalUnal1]

Muito obrigado. Estou feliz que você gostou. Saudações da Turquia.

[@王祥祐-d8v]

謝謝分享～👍～😄～！

[@CelalUnal1]

感谢收看。

[@jamesbernardino1754]

In the fact ....o ser humano ..nao é fraco nao ...congratulation....from Brasil..

[@CelalUnal1]

Muito obrigado.

[@hectorflores6097]

Great!! you are a very talented guy, cheers!!! i'm from Mexico and i really enjoy your videos.

[@CelalUnal1]

Thank you very much.

[@hasimcansozer7466]

Elinize sağlık, çok güzel video olmuş. Ben de benzer bir şey yapmıştım ama testerenin kesim yüksekliği yetersiz kaldı. Daire testerenin markası ve bıçak çapı nedir? Teşekkürler.

[@CelalUnal1]

Çok teşekkür ederim. Beğendiğine çok sevindim. 6cm civarı bir yukseklıgı var

[@layrtonsilvasoaressoares2687]

Que presisão, Parabéns e Gratidão por compartilhar!!!

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

[@Daianinha781]

Show de projeto.. parabéns! 👏🏾 Como você fez pra mudar o corte pra 45° depois de instalada a máquina na bancada? E me fala a marca e modelo dessa serra circular que você usou por favor, vou tentar fazer! 🙏🏾🙂.. obrigada pelo projeto! Abraço, sucesso!

[@marceltonel]

Oi Daiane, a maioria das serras tem o ajuste de 45° na própria base.

[@ВикторБуров-ш6ю]

@@marceltonel a serra tem um ajuste de 45 graus, mas há dois cortes separados na mesa e é impossível mudar o ângulo sem remover a serra!

[@jorgearturomontoyaz9600]

@@ВикторБуров-ш6ю de repente , lo quito y lo ajusto FUERA DE CAMARAS..

[@_dumi4451]

I watched a lot of your videos and i'm amazed by how smart you are. All my apeciation.

[@CelalUnal1]

Thank you so much. I am so glad you liked it.

[@dogo2462]

Video very useful, your carpentry skills are very good.

[@CelalUnal1]

Thank you so much. I am so glad you liked it.

[@woodturnet]

Зачем при наличии хорошего пильного станка, делать ещё один?

[@CelalUnal1]

Я сделал это, потому что этого хотели мои новые последователи.

[@МестныйЖитель-ъ6щ]

Чтоб одинокому столику не скучно было..Когда то и я соберусь с силой воли и сделаю себе такой же👍

[@ronaldolssantana2062]

Só o luxo 👍🏽 👍🏽

[@CelalUnal1]

Muito obrigado.

[@obrasilreal1506]

Um excelente projeto, parabéns!

[@CelalUnal1]

Muito obrigado. Estou tão feliz que você gostou.

[@jayejaycurry5485]

Fantastic job. Very clever. I just might build my own.

[@CelalUnal1]

Thank you very much. I'm so glad you liked it.

[@serbakayu]

thanks for the tips, very inspiring, greetings from carpentry, I'm a beginner KZbinr

[@CelalUnal1]

Thank you so much. I am so glad you liked it.

[@МихаилАлексеев-ш8ц]

Один из немногих действительно полезных роликов. Спасибо

[@CelalUnal1]

Большое спасибо . Я так рада, что тебе понравилось.

[@azza1793]

Personally i would not use a table saw without a riving knife to prevent kickback

[@CelalUnal1]

I've used this a long time ago. Again, there was no cleaver. If cut is done in a hurry, it does not rebound. Adding a riving knife to this workbench is easy to do.

[@blahdiblah2169]

@@CelalUnal1 No offense, but you should out of a public service just take this video down. You're promoting unsafe practice and might be somewhat indirectly responsible for someone else (or even yourself) losing a finger, getting his hand mauled, suffer some internal injury or poke an eye out.

[@randenstevenson4041]

@@blahdiblah2169 not going to blame anything at all on this man or his video but i built a saw table alike this one without the guard or riving knife to follow the board and within i’d say 10 cuts a 15x18 3/4 MDF board kicked back and went through a wall of 1/2” sheet of plywood .. always best to just be safe with it and add a riving knife of some sorr

[@randenstevenson4041]

and the wall is about 6 feet away from the blade itself, dangerous and every kickback will be different, some potentially deadly

[@julio74691]

Trabalho maravilhoso!

[@CelalUnal1]

Muito obrigado.

[@docentov]

Как сделать настольную пилу при помощи другой настольной пилы. Оригинально ((((

[@jorgearturomontoyaz9600]

Gracias por tu mesa de trabajo ! Es muy bonita y util , saludos desde Peru.👍

[@CelalUnal1]

Muchas gracias. Me alegra que te guste. Saludos desde Turquía.

[@SDG0213]

Uses table saw to make table saw... genius! Why didnt I think to ever just usea table saw to build the table saw that I dont have.

[@ahmetoztel1905]

Tebrik ederim, gerçekten mükemmel bir iş çıkardın.

[@CelalUnal1]

Çok teşekkür ederim. Beğendiğine çok sevindim.

[@papillondenuits5675]

Ça fait plaisir de tomber sur une vidéo qui blocs pas nôtre ordinateurs pour nous forcé à regardé la publicité🙏🙏🙏😘😘😘

[@CelalUnal1]

Merci. Je suis si heureux que vous l'ayez aimé.🙏🙏🙏

[@ccrlabuan2515]

Mejanya sederhana ,alat pembuat mejanya wow,,,,hadeh

[@CelalUnal1]

Terima kasih banyak.

[@frost20122013]

Que belleza de trabajo, muy buen trabajo... gracias por compartir

[@CelalUnal1]

Muchas gracias.

[@deltafromuknow5153]

Went to hit the subscribe button...I already was...🙏... You're my favorite joint making guy... Much respect my brother

[@CelalUnal1]

Thank you. I'm so glad you liked it.🙏🙏