Centrifugal Pump Curves - Performance and Characteristics

Learn about four types of curves that use to look at various pump parameters. And also about the pump family curve used in pump selection.
1. Head Vs. Flow Curve (H-Q Curve). 2. Efficiency Curve. 3. Power / Energy Curve. 4. NPSHR curve and 5. Pump Family Curve
Course link - courses.hardhatengineer.com/c...
Subscribe -goo.gl/9OktFA
Visit My website for more free piping study material - hardhatengineer.com/
Piping Courses for Oil and Gas Career Success
courses.hardhatengineer.com/
Learn About Pipes Used in Oil and Gas
hardhatengineer.com/pipe-clas...
hardhatengineer.com/pipe-clas...
hardhatengineer.com/pipe-clas...
hardhatengineer.com/pipe-clas...
hardhatengineer.com/pipe-clas...
Learn About Pipe Fittings Used in Oil and Gas
hardhatengineer.com/pipe-fitt...
hardhatengineer.com/pipe-fitt...
hardhatengineer.com/pipe-fitt...
hardhatengineer.com/pipe-fitt...
Learn About Pipe Flanges Used in Oil and Gas
hardhatengineer.com/types-fla...
hardhatengineer.com/orifice-l...
Other Topics
hardhatengineer.com/blog/
Piping Videos
hardhatengineer.com/piping-vi...
Piping Drawings
hardhatengineer.com/how-to-re...
hardhatengineer.com/pid-pfd-p...
My other videos :
How to read P&ID- • How to Read P&ID Drawi...
ASME Code - • What is the difference...
Fundametal of Pipe - • Fundamental of Pipe (P...
Pipe Gasket - • Pipe Gaskets for Proce...
What is MAWP - • What is MAWP, Design ...
Pipe Fittings - • Pipe Fittings - Elbow,...
Pipe Vs Tube - • What is the difference...
Pipe Flanges - • Learn about 6 Main Typ...
Piping Training - • Piping Material Select...
P&ID - • P&ID Symbols Drawing a...
Flanges - • Learn about 6 Main Typ...
00:00 Introduction
01:04 Head Vs. Flow Curve (H-Q Curve for Centrifugal Pump)
02:18 Efficiency curve for pump performance testing
03:35 Power or energy curve for Centrifugal Pump
04:05 NPSH required curve for Pump
04:31 Centrifugal Pump overall performance curves
05:01 Family Curve for Pump selection
#hardhatengineer #Pump #Inspection

[@HardHatEngineer]

Test Your Self, Take This Short Quiz of 10 Questions on Pump - learn.hardhatengineer.com/ytpump

[@vickyd1079]

Sir I want to calculate the head range of pump so how can I calculate the head range of both submersible and centrifugal pump

[@vickyd1079]

As I have graph of Head vs discharge and input Power vs discharge....

[@naveennair1133]

Thank you sir 🎉

[@grandhivenkatachalapathira1588]

Nice one. Please make a video on reciprocating pump curves brother

[@shivasmart967]

tq sir

[@mangam6369]

Brilliant just please could you explain how the head is against the flow rate however when we need to increase the flow rate we will add a more stages

[@HardHatEngineer]

More stage will not add extra flow. It will increase the head.

[@tringuyen1979]

Thank you for your dedicated video! May I confirm my understanding: the power perfomance curve and the power in pump family curve are about the mechanical power (shaft pump power)?

[@HardHatEngineer]

Yes, correct

[@tringuyen1979]

@@HardHatEngineer Thank you Sir! I have another question: In some hydraulic calculation documents, I found 2 different values of efficiency: estimated and corrected. How can we get those values? I guess the corrected efficiency is got after we have already chosen the pump, and calculated by hydraulic power/mechanical power. Am I correct? How about the estimated one?

[@leonelbinungcal4065]

Where can I get these charts that will correspond to my pump's brand and specification?

[@HardHatEngineer]

You have to contact pump manufacturer.

[@RR-om4rr]

Why efficiency decrease after reaching maximum efficiency

[@dheyaalgallaf6060]

How to accomdate viscosity impact on pump curve in design, while pump's curve from vendor is for water?

[@HardHatEngineer]

Vendor will give you chart for correlation.

[@vishnuvardhanreddy709]

SIR CAN U GIVE A CLASSES FOR MRPL EXAM

[@HardHatEngineer]

Not available with me

[@jodymuniz8555]

Can you please provide me the link to take the course advertised for Real PLant Examples ??

[@HardHatEngineer]

Hi, here is the link - courses.hardhatengineer.com/courses/rotating-equipment-bundle-4-in-1

[@binods6216]

please help me with formulas to find efficiency

[@phakyou]

Why does head vs flow curve contradict with the equation Q=Cd×A×sqrt(2g)h^3/2?

[@northernethiopia6538]

Thank u so much sir can i contact u through gmail

[@sakdasaosa9746]

How long can I take time for shut off test?

[@HardHatEngineer]

not more than 3 minutes.

[@sakdasaosa9746]

@@HardHatEngineer Thank you

[@abhishekrokade328]

Why eccentric reducers are used in suction side

[@HardHatEngineer]

to avoid air trap.

[@sumitpaul4682]

@@HardHatEngineer How?

[@mdzeeshan8598]

Pdf

[@AxatS]

At 6:03 Sir, you said u sould maintain more than 9 ft of head to avoid cavitation!! Don't think you so sir, it should be below 9 ft and not more than this to avoid cavitation ?

[@FirozAhmedblogs]

Need maths for practices