New Centurion d10 installation in Ghana. in this video, you will learn how to set the limits on your Centurion D10 automatic sliding gate machine. @Centurion Systems #CenturionSystems #EtronsecSolutions
Пікірлер: 59
@stormdavies1373 Жыл бұрын
The most beautiful gate and handle at the end.. that is genius!
@EtronsecSols Жыл бұрын
Thanks
@FarukAAdavs2 жыл бұрын
Thanks bro, your video has help me 🙌🏾
@nycomsystemservices Жыл бұрын
Well done my guy and thanks for sharing and the information
@EtronsecSols Жыл бұрын
Thanks man
@bediakochristian59832 жыл бұрын
Tanks bro u makes me understand it mor Dan my master tanks
@hsbtechnologies26622 жыл бұрын
Merci beaucoup mon frère,
@EtronsecSols2 жыл бұрын
Il y a pas de quoi
@calvinmaretele7282 жыл бұрын
Thank you man
@kelseyakosuafrimpomaa45012 жыл бұрын
Well done dear🥰
@EtronsecSols2 жыл бұрын
Thank you 😊
@aiyelesobabajide39252 жыл бұрын
Weldone
@EtronsecSols2 жыл бұрын
Thank you Sir.
@wilsonhomeli32784 ай бұрын
Machine is on on limits set
@RichardMaluleke-f1y7 ай бұрын
Awesome
@thandidlamini50492 жыл бұрын
thanks dude
@solomontimothy53993 ай бұрын
Well done bro. U didn't add remote
@nsovobonica1116 Жыл бұрын
So even d5 evo i must push it to da middle when i want to program it?
@EtronsecSols Жыл бұрын
Yes it's advisable to. Just to allow the gate to move freely either way
@mziwamancunuprojectsltd5980Ай бұрын
How much do u charge for installation tnx
@EtronsecSolsАй бұрын
Text me on 233550431624
@el-adol2 жыл бұрын
I tried resting the limits but it wasn't successful. I got error message "!!SETUP FAIL!! NO ORIGIN FOUND. What could be wrong?
@EtronsecSols2 жыл бұрын
You have to make sure the magnet on the gate passes close to the blue sensor (origin sensor) in the machine. The sensor should click anytime the magnet passes by
@el-adol2 жыл бұрын
@@EtronsecSols the magnet passes through the sensor. The stopper for the open limit is on the rail. Is there meant to be another stopper aside the one on the track?
@EtronsecSols2 жыл бұрын
As long as your gate can stop at each end, you are good. But does the sensor click when the magnet passes in front
@el-adol2 жыл бұрын
Yes the sensor clicks when the magnet passes & gate does stop at both end. At closing, first stop end was found, but when it opens fully and stops, I get the error message "SETUP FAIL!!! NO ORIGIN FOUND" and it doesn't move again.
@EtronsecSols2 жыл бұрын
@@el-adol please kindly check the screen while the magnet passes by the sensor to see if you will get any message like " origin at left " or "origin at right" if not you should consider checking the origin sensor wiring for good connection or even replacing it. +233550431624 you can WhatsApp this number for further help
@philipomamacito49692 жыл бұрын
Is it possible to make my D10 smart
@EtronsecSols2 жыл бұрын
Not really! We now have D10 smart. But you can add ( G-ultra to the old one in order to operate it via your phone)
@mphomainetja3996 Жыл бұрын
Hi, after pressing start, the power goes off and restart the PC board. What could be the reason?
@EtronsecSols Жыл бұрын
Check your battery terminal or replace the battery
@silvamoz62994 ай бұрын
Faulty power circuit board
@servatectv49462 жыл бұрын
Hi please I want one to buy
@EtronsecSols2 жыл бұрын
Business done
@FrankVanhollstein-vi7jo Жыл бұрын
Problems on the org
@efyaranda54402 жыл бұрын
Hi I need your line please
@EtronsecSols2 жыл бұрын
Kindly call us on 0550431624
@adjeirichard78332 жыл бұрын
Well done bro n keep it up ✌️
@magnificent360ng Жыл бұрын
Nice video Man, how do I fix similar machine that is slow to open and close?
@EtronsecSols Жыл бұрын
It's possible to reduce the speed and make this machine go slow
@magnificent360ng Жыл бұрын
@EtronSec Solutions Gh I got two error messages when trying to set limits the First one is "END STOP DISTANCE DOES NOT MATCH, LIMIT SETUP FAILED" The second one is "BATTERY VOLTAGE TOO LOW"
@judechukwuemekaalbert846 Жыл бұрын
How can I program my D5-Evo to open with my car homelink botton
@EtronsecSols Жыл бұрын
I have tried sometimes and it failed but I will do a video covering that issue
@moisebagumandihano2710 Жыл бұрын
Hey man I have D5 evo motor. I have done all the settings and followed instructions but when the gate starts for the first time it is not finishing the complete cycle. The controller is switching off itself then restarts. Can you please assist ?
@EtronsecSols Жыл бұрын
Hi Boss! Kindly check the battery Terminals and make sure the power supply is on
@judechukwuemekaalbert846 Жыл бұрын
Maybe your battery is faulty
@ithinkican0072 жыл бұрын
Where is your office andHow much for the machine?
@EtronsecSols2 жыл бұрын
We are close to palace mall. Spintex road. Kindly call us on +233550431624
@victoraddo16512 жыл бұрын
How mach is the machine
@EtronsecSols2 жыл бұрын
Kindly contact us on 0550431624
@mtandanamike56152 жыл бұрын
I need help
@EtronsecSols2 жыл бұрын
How can we help you
@mtandanamike56152 жыл бұрын
@@EtronsecSols can get your number so that I can give you call so that u can assist mee with the setting of gate motor d10
@EtronsecSols2 жыл бұрын
@@mtandanamike5615 the video should be clear enough. Where do live