Borgeson Steering Shaft For The Dodge W150

LIKE, COMMENT, SUBSCRIBE!!
Use coupon code cm73 www.hotshotsecret.com/cm73/
Amazon amzn.to/30ywAP0
Complete Borgeson shaft amzn.to/3lrp82h
Borgeson 1/2 shaft amzn.to/3hRxsrt
POPOMAN TOOLS Store amzn.to/3irh0gR
Follow me on Instagram, Twitter, and tiktok: @chad_myers73
Send stuff to this address:
2344 Shawnee RD
PMB 118
Lima, OH 45805
Music by Thomas Green / @thomasgresen
My tools I use!
Drill Driver Set amzn.to/2JhH6St
Subby Impact amzn.to/2QRQKPN
Torque Wrench amzn.to/2R8hXgD
OLSA Tools Store amzn.to/2ZYskHP
MYCHANIC Stores amzn.to/2LnS49J
Canon camera amzn.to/2OdsQdx
JOBY 3K tripod amzn.to/2qe9ewe
Needler Descaler amzn.to/2xEfEbM
Topside Creeper amzn.to/2xgiSSE
Bed lift amzn.to/2Je64lj
Evolution saw amzn.to/2pxwxkp
Dewalt grinder amzn.to/2CYQ7j4
Clamptite Tool amzn.to/2NKnQRv
IR 3/8” impact amzn.to/2QojGgp
Dewalt 1/2” impact amzn.to/2x8peTB
Foam Canon amzn.to/2QpE9RS
Solder connecters amzn.to/2O9leZh
Power Prob amzn.to/2QbRHjL
#3rdgencummins #2ndgencummins #cummins #chadmyers73 #harborfreight
DISCLAIMER: This video and description contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission. This helps support the channel and allows us to continue videos like this. Thank you for the support! We cannot do this without YOU!

[@joshuatall8134]

I just picked up an 89 W150 with way too much play in the steering wheel. Thank you for helping me get my rig fixed! Great video!

[@ChadMyers73]

Thanks for watching!

[@flyfisher1115]

Great video man I’m about to do this on my W250 and it answered all my questions

[@ChadMyers73]

Thanks for watching! It is a great upgrade…

[@jasondiakiw1579]

Great video , removing the roll pin on steering wheel side is key , if you don’t have an air driven tool I used a hammer drill and cut off the drill bit head , 3/16ths bit , came out instantly after trying to drive the pin out manually with hammer and punch

[@ChadMyers73]

Cool thanks for the info!

[@sethvance1289]

Got a 89 ramcharger that I’m putting a similar shaft on, was looking for a good video to explain how the shaft comes off the truck. Your video was very good and had great information. Thank you.

[@ChadMyers73]

Your welcome and thanks for watching!

[@mattgeiger2627]

Answered all my qustions and a quality video. Ty. Thumbed up and sub.

[@ChadMyers73]

Thanks for your support!

[@LookAtMeNow26]

What’s the reasoning of re-using that spring? I’m doing mine right now and feel like it’s kinda sketchy that the spring could push the u-joint off the upper spindle- only that 1 lock holding it. Thanks for the great write up!

[@ChadMyers73]

Yeah I went back later and removed it

[@Neverquit275]

Hey Chad, great Video! I'm installing on a 08 6.7L Did you set the bottom spines all the way down the steering gear shaft splines, so it bottoms out or butts up against the gear box at the bottom of the shaft. I see some just put in on the first part of the shaft before the dip and file a flat spot, but it seems like it barely on the shaft by doing it that way. I also see one or two run it all the way down and just backing off a hair. and filling a flat spot on the spines on the bottom part. I don't really see anything on Borgenson site either way

[@ChadMyers73]

I did put it down all the way and then pulled it back a bit

[@koioo2]

sometimes a part is to old and better to replace

[@ChadMyers73]

Absolutely it was time for an upgrade!

[@trjo104]

Help! I can't get the cotter pin out of the top of the steering shaft for removal. What can I do since you can only punch from one side to push it through. Rusted on. Ideas??

[@ChadMyers73]

Flood it with penetrating spray let it soak and try hitting it with an air hammer with a punch end

[@hiltbuilt9837]

Where you been

[@ChadMyers73]

Life in general my son has a busy race schedule.

[@ChadMyers73]

Sorry man will be back soon

[@DPats1228]

I bought this shaft for my 06 mega cab. I removed it. Went back to a new stock shaft. The set screws kept loosening up on my and causing popping. Even with Loctite. Etc. 8” lift on 37s.

[@ChadMyers73]

I’m sorry to hear that. I’ve used 2 of them with no issues(knock on wood) 🤣😂

[@DPats1228]

@@ChadMyers73 must be nice! Ya. I was constantly re tightening everything. But hope it works well for you!

[@ChadMyers73]

Thanks for watching!

[@Isteveym]

Thats the thing with these shafts they are a solid connection no cushioning from pot holes or rough street roads . If anything will be harder on gearbox the oem shafts are designed that way for a purpose.. manufacturers do spend alot of money in most of their designs specially steering . This shaft would cause alot of issues for manufacturers warranty repairs etc ..