My steering is loose on my 82’ K5 square body. This is motivating me to fix it my self. Wish I had a garage like yours. It’s hot af where I’m at. I’ll wait for cooler weather so I could do it on the street. Your K5 looks like you changed everything on it. Mine is old and rusty. I have a lot of work to do. I just subscribed to your channel and I hope I could find more good info like this. Thanks again you gave me confidence to move forward
@joshuaatkins5197 Жыл бұрын
Both Borgeson and Flaming River make very nice aftermarket steering shaft but too expensive. A much better budget option would be to buy the parts from Speedway motors. They have builder parts 4 hot rod steering shafts and any configuration. I purchased 2 high quality joints with the correct spline count and a 3/4 solid round bar for just over $50. Welded it together with a slip in the middle and a safety bolt thru each welded area in case the weld ever breaks. The come in bolt together or weld together options. You can build it without a slip but its way easier to take the extra time and make it slip for easier removal anytime.
@miguelamartinez14115 ай бұрын
Step by step video. Thanks a lot, from Colombia.
@BloodshotEagle Жыл бұрын
Great video! I’ll do this on my 87 ! Thanks man
@Noslo_559 Жыл бұрын
Thanks for the video. It was so easy to install after watching this. I installed it in the dark with a headlamp. Step by step was perfect. Thx again.
@UintaGarage Жыл бұрын
Thank you for the comment/feedback! I'm very happy to hear this helped someone :)
@Kurnacopia2 жыл бұрын
Outstanding work!! I'm going to deploy this idea on my 1978 Chevy Scottsdale 4x4 asap!!
@ramonramos70066 ай бұрын
Great video and details Thank you..👍
@olsonspeed Жыл бұрын
Thanks, my new shaft is on it's way, your video is extremely informative.
@chancbennion2861 Жыл бұрын
Thank you, brother! Great video, and I'm super excited about installing my new borgeson steering shaft
@grantchandler721023 күн бұрын
Did you guys ever post the video on the xj steering shaft. I’ve got a 72 k5 and I think the xj shaft I bought has 30 spline. My gear box is 36 spline. Wondering if you found one that works for you gen 1 blazers.
@UintaGarage18 күн бұрын
We haven’t dropped the XJ shaft video as of yet. As for the difference in gear box spline, we ran into this with a swap for hydro assist and were able to get just the coupler end from Summit with the right splines.
@rudylarez43608 ай бұрын
Clean engine compartment
@UintaGarage8 ай бұрын
Thanks!
@glfmarmadison5126 Жыл бұрын
Thanks
@vgslife96402 жыл бұрын
great video bro
@WiiHunt95 Жыл бұрын
You should look into quick draw from momar, I love it. It's a great grease and one of their many
@UintaGarage Жыл бұрын
I'll check it out!
@WiiHunt95 Жыл бұрын
@@UintaGarage you will find all kinds of stuff that you will love
@mark80122 жыл бұрын
I’ve done the Borgeson upgrade a couple years ago with no regrets. I had to get a different lower joint. The one listed did not fit the PSC steering box. Great info on the lower bearing.
@josephsmyth73348 ай бұрын
Great info. But why no grease on the spline just in case it had to be taken off again?
@UintaGarage8 ай бұрын
That's something to consider. Maybe we will do that on the next one.
@calircpilot42618 ай бұрын
Great upgrade seemingly, I also own a factory untouched ‘88 K5 and looking for the Jeep steering shaft option, I saw both, the Jeep shaft and the bearing kit in your Amazon store, can you please confirm this is the correct part I will need? SecosAutoparts Lower Power Steering Column Shaft Compatible with Jeep Cherokee 1984-1994 Comanche 1986-1992 Replace# 4713943 and Crown Automotive 4487696K Steering Shaft Bearing Kit? Is the Jeep shaft a drop in option or Will I have to custom anything? Thanks again for a great video tutorial
@UintaGarage8 ай бұрын
We installed the crown bearing and jeep shaft from our Amazon store on an 84 k5 and they worked perfect. You just need to heat up the plastic keeper in the middle to allow the shaft to collapse a little.
@calircpilot42618 ай бұрын
Sorry, heat up the factory shaft or the New Jeep one??. Thanks for the speedy reply
@Blakep7704 Жыл бұрын
Do you get more vibration through the steering wheel? What is the purpose of the rag joint?
@UintaGarage11 ай бұрын
No I didn't notice any additional vibrations.
@REDLIONJaxFL6 ай бұрын
I saw the Jeep steering shafts on the table. Why didn't you use that one? I just watched videos about it. I have a 95 k3500 with the old rag joint. The "Jeep Cherokee XJ shaft swap" you dont have to cut it.
@UintaGarage6 ай бұрын
We did the xj shaft on another truck video coming soon. Both are great options
@REDLIONJaxFL6 ай бұрын
Since I have the 1995 k3500 everything I've been looking at so far shows me that I can't use the XJ shaft on my truck I guess something changed in the 95 and up. I'm not sure what the difference is but a 93 and the '95 rag joints look the same so I don't know why I can't do the swap in my truck hopefully your video comes up soon cuz I'm looking for a cheap option that I can do for my truck@@UintaGarage
@philipworcester72592 жыл бұрын
On the upper joint where you drilled the 3/8 hole. Did you drill for the set screw as well? Thanks for the video!
@UintaGarage2 жыл бұрын
The hole we drilled in the one side is for the set screw to go through then it tightens against the other side we didn't drill out. There is just the one hole through the one side of the shaft. I hope that helps.
@TonyParsons-h8q Жыл бұрын
Hey Joe where are you located? I live in Kamas UT. Literally gateway to the to the uintas
@UintaGarage Жыл бұрын
We are in Riverton and salt lake valley
@markelrod8144 ай бұрын
The best "how to not use tools" video I've seen in a while.. 😂😂😂
@UintaGarage4 ай бұрын
Thank you sir
@Davidhillborn5 ай бұрын
How much play will this eliminate? Is it worth doing without also installing a new steering box?
@UintaGarage5 ай бұрын
On all the vehicles we have done this on we also replaced the steering column bearings that were shot between that bearing and this steering shift the steering was significantly tighter and more responsive feeling.
@shortcutgarage2 жыл бұрын
Inspired me to grab one to do up for my KZbin channel. Just getting started. Be sure to check It out!!
@thatguy_jose2 жыл бұрын
Hey Joe, great video. I have a 74 k10 with a 69 c10 cab. will the cj jeep shaft work fine. some say I'll get a little of vibration from the frame.
@UintaGarage2 жыл бұрын
I haven't noticed extra vibration on any of the trucks we have done this on. The xj shaft should work. Just check to see if your steering column has the double D end on it vs the spline drive.
@markmontes34692 жыл бұрын
Hey man love your video! Im about to install this on my 79 c10. Im just confused on why you cut it twice? If you can please explain that be great
@UintaGarage2 жыл бұрын
Hey Mark, The steering shaft comes really long, so long that you can't fully extend it without cutting a little off first. I believe they send it really long for folks with body lifts or who may have moved the steering box forward. I bet you could measure the distance between the steering column and box and make just one cut however this is the method they suggest and it gets you 100% dialed in.
@markmontes34692 жыл бұрын
@@UintaGarage thank you for your reply! Love the square body! I was thinking it extends a lot more than just pulling it. Makes sense now! So I shouldn’t need to pull it more whenever it is on the steering box?
@here_to_watch2115 Жыл бұрын
Measure once and cut twice !
@JustinLorance Жыл бұрын
I bought the Borgeson shaft to do this but can not get the upper shaft assembly to attach to the steering column shaft. Did you have any issues with this?
@UintaGarage Жыл бұрын
I did not, however, I have seen others that needed to grind a little material off the end of the column or bore out the inside of the double D on the shaft.
@freewookie1971 Жыл бұрын
Having the same issue!
@MarkSzela Жыл бұрын
Do you have the part number for the steering shaft bearing kit on a 1975 chevy k5 blazer?
@UintaGarage Жыл бұрын
I think it's the same as the later 70s and 80s. Check out out Amazon store we have it on there. Www.amazon.com/shop/UintaGarage
@timarchuleta65522 жыл бұрын
Great video! Do you know if this will work on a 74 K5 Blazer? Any info would be appreciated.
@UintaGarage2 жыл бұрын
It's a very similar process but they have a different part number for the steering shaft. Borgeson has it on their website. It's a spline drive vs double D.
@timarchuleta65522 жыл бұрын
@@UintaGarage Thank you!
@johntadeo37292 жыл бұрын
Do you guys still have the chrome bumpers from the k5 blazer lol I need sum but don’t want to pay for a new one and wait because they are back ordered
@UintaGarage2 жыл бұрын
It's funny you are not the first person to ask 😂. The bumpers from this truck were sold many years ago.
@johntadeo37292 жыл бұрын
@@UintaGarage 😂😂 it was worth a shot I was just a year late thank you though and keep up the videos 👍👍
@estevendouglas6957 Жыл бұрын
Are you getting any added vibrations from the road since you replaced the steering shaft with a solid shaft? Sine you have no rubber bushings to cancel this from the factory steering shaft?
@UintaGarage Жыл бұрын
I didn't notice any additional vibrations at all.
@4AGTurtle Жыл бұрын
At 5:24 what’s that part called. Steering shaft bearing?
@UintaGarage Жыл бұрын
Steering shaft bearing. You can find it on our Amazon store under "steering shaft upgrade" www.amazon.com/shop/UintaGarage
@mandis1024 Жыл бұрын
@@UintaGarage Will that bearing fit an 81 K30 do you know?
@UintaGarage Жыл бұрын
@@mandis1024 I'm fairly certain it's the same in all the 80s chevys
@REDLIONJaxFL6 ай бұрын
Is the bearing the same for 1995 k3500@@UintaGarage
@shannonlove1981 Жыл бұрын
Did you do the ford shock towers
@UintaGarage Жыл бұрын
I did. However I'm switching to the Diy4x shock towers this year so my shocks are more vertical
@lsu614 Жыл бұрын
Did it make any difference?
@UintaGarage Жыл бұрын
Yes, firmed up the feel of the steering
@patrickcombs65672 жыл бұрын
Did you use the factory 15mm bolt hole that you removed on upper steering column shaft to attach the upper Borgeson joint to?