An A-1 Compressor Technical Video for refrigeration technicians on "How To" change a Carrier Compressor 06D & E Valve Plate in the field. Call us at 800 743-6009 for replacement parts and more information
Пікірлер: 45
@1jardmadman Жыл бұрын
I use to grind yalls crankshafts. And ALOT of others as well. Altho that was bout ten years ago 🙁
@shabazbaig62388 жыл бұрын
It's very helpful for me for overhauling.Thanks
@cmtwok7 жыл бұрын
Thanks A1. I'm going to attempt dissecting a 06 tomorrow and hopefully won't get fired.
@wwefan61911 Жыл бұрын
Did u get fired?
@don.richard88236 жыл бұрын
Good video thanks for sharing
@saltrue15556 жыл бұрын
Thank you very instructive thank you so much
@mujahidahmed32254 жыл бұрын
Very good information thanks brother
@EminHVAC10 жыл бұрын
good information thanks for sharing it.
@laymanforchrist59326 жыл бұрын
Never forget to change out your oil and pull vacuume before opening service valves.
@juns.quilaton98003 жыл бұрын
good tutorial sir
@tchebatk34077 жыл бұрын
Antigão esse muito bom de manutenção.
@ZuffaLtdDanaWhite8 жыл бұрын
@A-1 Compressor: Would you recommend using Nylog as a gasket sealant during the valve plate repairs/replacements? Thank-You. -Ian S., Vancouver, BC, Canada
@annegao70483 жыл бұрын
good video
@technicalmindkhan55735 жыл бұрын
Nice sir thank
@eagletran92 жыл бұрын
Thank you sir
@crizzcross5 жыл бұрын
where would the broken piece end up should we spend time looking for it in the system?
@mdgilman7866 жыл бұрын
Hey brother can u tell me about Carlyle 06 E compressor head replacement right procedure when em changing metal gasket with complete head assembly then after replace creating sound from head due to becker n suction valve but i hv tried many times but couldn't succeed the old one discharge valve broken from top so than it was easily taken the suction gas
@user-nf8jr2ov8x7 ай бұрын
How do you diagnose broken valves? what are the symptoms?
@arcadenew368510 жыл бұрын
why you should not use the suction back reed on low temperature? only in medium to high temperature, and if I use for a working pressure of 15 to 10 psi. thank you for your attention. i am Brazilian technician.
@mdnaimulhoque30252 жыл бұрын
ধন্যবাদ
@2000badusha6 жыл бұрын
hi , can you provide the video for main bearing installaion of 06E (carlyle) compressor, thanks in advance
@ashrafatia87155 жыл бұрын
Can you make veidio about falts and how to make maintinance for it
@cuongcuong68205 жыл бұрын
Could you tell me.how to add refrigent to chiller centrifugal please
@nisw19189 жыл бұрын
By the way how do you add oil just open the plug and add or is there a sequence to it .Thanks again gave you a thumbs up
@actechformallyyomama7465 жыл бұрын
nisw1918 you need an oil pump to add oil. Let the compressor run a while before adding oil. On an 06E compressor the oil level should be at the bottom 1/3 of the sight glass. It can be at the bottom and the level is still ok. 06D compressors should be about 1/2 sight glass. If the sight glass is low the oil is probably in the circuit. Do not add oil until you confirm it’s not in the circuit. The oil will coat the evaporator tubes so the refrigerant will not evaporate properly causing the compressor to flood back. Run the head pressure up to get the oil back to the compressor before adding oil. I have removed more oil than I have put it in. A system with too much oil will kill the compressor.
@didierortega36657 жыл бұрын
ola necesitó el manual de fabricasio del compresor carrier
@mfn3502 жыл бұрын
What could be cause this compressor ampere keep on hiking..let say it start with 39 Amp with in 15 minutes it become 56 Amp ...and the compressor trip on overload.
@salmoneries3 жыл бұрын
Hello, can i use ure video for my french channel? frigoriste chaine du froid. TY
@samirasamiraaaaa70532 жыл бұрын
Hi. I have a problem with a compressor model carrier that discharge is bypass to oil pass. Can you help me?
@user-yy7rd3tc2r8 жыл бұрын
这什么牌子的制冷机
@didierortega36657 жыл бұрын
que. altura tiene la vase que pisa los flores de. alta
@didierortega36657 жыл бұрын
los flaper
@bastian31828 жыл бұрын
Like si vienes por la tarea 2 de Refrigeración
@nicolassaezluna70728 жыл бұрын
+Bastian Palavecino jajajajjajajajajaj no me esperaba esto
@mariopalacios55308 жыл бұрын
+Bastian Palavecino que significa este desorden ?
@OscarGutierrez-li3pt7 жыл бұрын
Nicolas Saez Luna 0ut
@cristobalrivera34395 жыл бұрын
jajaja, vengo por lo mismo
@mdgilman7866 жыл бұрын
Sir can i get ur fb page or any other platforms for discussion or facebook id etc ur response will be precious for me thank you.
@user-es7ib5gq4s3 жыл бұрын
Hi sir I am from Iraq I have about 15 years experience in maintenance of cooling systems also over haul maintenance of centrifugal and reciprocating compressors can I work in your work shop thanks alot
@kalimullah44873 жыл бұрын
Hello
@armanalam95777 жыл бұрын
I'm working at compressor overall please give me 1 chance Saudi Arabia my company name elmac