Cheap Pen Torch Review

This cool little torch is awesome for its price, you can fill it with ordinary butane gas, and flame gets really hot, it doesnt have any problem heating steel ball to a red hot danger hazard :)
Link for the product here :
www.ebay.com/it...

[@superclips5467]

About time a review that is actually a review in doing some work with it! Thanks

[@veryfatjunkie]

Hi. Can i weld very thin sheet of steel. Like fountain pen nibs ? Kindly reply

[@DIYGarageProjects]

I think you cant weld any type of steel with propane burner, at least not with this one

[@veryfatjunkie]

DIY Garage Projects and reviews what about brazing?

[@DIYGarageProjects]

You could braze some small aluminium and brass pieces with this burner

[@jonathandawson4344]

I have a few pencils torches that just make a huge flame like a flame thrower can I fix this mayby by changing the tips and if that's how can I use tips from different kinds or does it have to be the same kind thinks

[@TauCu]

Oh, I'm not sure if you still have this problem, But with the torch i have, You can remove and take apart the jet assembly by pulling the brass sleeve off of it, Don't use excessive force though... And then just clean anything out, Also, Make sure not to Overfill the torch with butane, or it will flare up, Just like if a BBQ were to run on Liquid. You can fix that by just letting it burn if that is the case.

[@deejay5493]

How long can this remain lit at a stretch without overheating the nozzle? How long does one charge of gas last?

[@DIYGarageProjects]

I wouldnt recomend this product since it clogs up alot, but when i used it it didnt overheat after 10mins of use

[@deejay5493]

@@DIYGarageProjects Yes, I read that in the comments, but I'm just looking to use it as a one-time solution for replacing just one SMD component on my old PC motherboard. The component to be replaced is located in a low-density section of the PCB, so I'm not concerned about overheating any adjoining components. This is the cheapest ESD safe method I can use. What say?

[@DIYGarageProjects]

Sound interesting, usualy they use hot air, i would like to see that, if you decide to try it, could you make a video and post a link here?

[@deejay5493]

@@DIYGarageProjects Yup, they do. But it doesn't make sense to invest in a hot-air rework station JUST to solder a dislodged SMD component. I'll'' give it a whack and will try to make/share a video. :-)

[@DIYGarageProjects]

Thanks ;)

[@livinlife7309]

After about the 3rd fill up, torch does not hold its adjustment. :(

[@DIYGarageProjects]

It happens alot, you need to dissasemble it and clean the little disc inside

[@muffen100]

Can you heat up heat resistant glass only till its red

[@aldirobert4277]

Ca you have the smallest flame out of this torch

[@alundrasrt]

What the temp of this? Thanks.

[@DIYGarageProjects]

+karim hassane not sure, sorry, thanks for watching.. btw i wouldnt reccomend it, it clogs really often

[@alundrasrt]

Thanks for the fast reply. Yes, you're right, it seems that the jet must be clean after 2 or 3 sessions. I'll go for jet butane lighter.

[@HoverFreddy]

Enough for melt glass

[@alundrasrt]

Thanks!

[@HoverFreddy]

Np ^^

[@jaredbingham229]

After about 30 minutes of use the jet clogs up and the Nozzle gets clogged up and the shaft is pressed on so you can't clean it, It's trash

[@lookup49]

Can you show how to clean it...not sure how to follow package instructions.

[@davidbolha]

lookup49 kzbin.info/www/bejne/fmTMf6SJo8uVj9U ? 😄

[@mujammilahmad8650]

Which price

[@spydkiss]

could you plz try making a small wood burning project using this torch? tnx!

[@DIYGarageProjects]

+spydkiss do you have a suggestion on what would you like to see?

[@rodstartube]

can it weld aluminum?

[@DIYGarageProjects]

It cant, maye some thin sheets with those soft welding rods

[@rolandschmidt8285]

Naja... eben ein nettes Spielzeug.

[@adepuhemanth2653]

Keep a give away contest

[@adryanvandenberg8264]

Does anyone Know how you can somehow put soldering tips on this ?

[@keithshreve6736]

Nice Video ! Thank ! You !

[@juliusvalentinas]

super bad soldering skills here.

[@DIYGarageProjects]

+juliusvalentinas you dont use this for soldering wires!!

[@juliusvalentinas]

well then why demo doing it then? the nozzle clogs really fast. That's because of poor design. this is only alternative www.ebay.co.uk/itm/Sievert-Turbojet-Single-Burner-360-Swivel-Torch/131990958284?_trksid=p2047675.c100623.m-1&_trkparms=aid%3D555018%26algo%3DPL.SIM%26ao%3D2%26asc%3D43782%26meid%3D8e4136af95364dd6ae46276a34ff2680%26pid%3D100623%26rk%3D1%26rkt%3D3%26sd%3D131990959785

[@adryanvandenberg8264]

I think this is more of a jewelry making tool

[@kordish_music_nostalogi]

It was very ridiculous, for example, what was the benefit of this video as much as the work of school children im sorry buddy

[@DIYGarageProjects]

Why are you sorry? Its not like ima telling you to buy it because its the best thing ever, i wanted to show you what it is, and if you want it get it, if not dont. Im not selling these nor im paid for the video.

[@kordish_music_nostalogi]

Your tests are simple and easy. Soldering can also be done with a weak lighter This is done by elementary school children no mr my age and yours

[@DIYGarageProjects]

But this is not any better than a toy, its cheap and low quality and cant do any serious work, what else to try

[@kordish_music_nostalogi]

You are right, I apologize