Cheap ebay garage door opener from china. $120. Perfect for metal garage car port style roll up doors.
Пікірлер: 75
@nikkiwyer90283 жыл бұрын
This is helpful unfortunately I know nothing about welding... but u do understand why you had to weld a piece in. I wish they made them to fit correctly for us low key DIY-ers.
@duneme10 ай бұрын
Do some more searching! I remember seeing it somewhere! I think it was KZbin! I think it’s meant for just the garages it fits! Roll up your door and take a picture from the side! See if the profile it is is what they provide by looking in the Instructions!
@coyotesnper Жыл бұрын
Do you have a video on programming the upper and lower limits of the door?
@huntah2k Жыл бұрын
Sorry i dont. Cant remember exactly how.
@Goatboy28652 ай бұрын
I looking for this too
@timeforfishing Жыл бұрын
is it strong enough to keep a person from forcing it open?
@huntah2k Жыл бұрын
Yes you cant move it.
@Brad-bm5jj3 жыл бұрын
How did you set to where you want your doors to stop at? These instructions suck. What do you do to set it where you want it to stop.
@huntah2k3 жыл бұрын
Im sorry i cant remember exactly how but i do remember setting the bottom first the the top afterward 🤷♂️
@RayBarao. Жыл бұрын
This is what I’m having an issue with. It’s only rolling the door half way up. I can’t figure out how to set it to roll all the way up
@gavinweller-my7um Жыл бұрын
Yes havein same problem as Ray ATM
@KRobTip4z3 жыл бұрын
Is that the style garage door that doesn't come with a chain pulley set-up that you have to manually push up with your hands like at storage facilities?
@huntah2k3 жыл бұрын
Yes same style. Has s coiled spring inside so its easier to open or close
@squid1482 жыл бұрын
I don’t see any safety lights on the bottom of the door. What if your kid 🧒 walks under it while in the down position?
@huntah2k2 жыл бұрын
It has a pressure sensor or something build inside. It will push a certain amount and then back off and go back up
@madeleyinc Жыл бұрын
You can always make another kid, hopefully a smarter one.
@gerardosanchez2812 Жыл бұрын
Does it close automatically or you have to close it ?
@huntah2k Жыл бұрын
It closes automatically
@duanecalhoon33223 жыл бұрын
Can you explain all the buttons on the remote? Mine has 4, will the same remote operate different openers???
@huntah2k3 жыл бұрын
Im not sure. I only use the one button to open and close the door.
@LauraLopez-gj5bs3 жыл бұрын
What batteries fit remote mine did not come with any batteries. Thank you
@huntah2k3 жыл бұрын
GP alkaline 27A 12v battery
@CoralEuphoria3 жыл бұрын
Thanks for posting. Not sure why anyone would dislike this video. Is this unit still going strong for you?
@huntah2k3 жыл бұрын
Yes still working great. No issues at all. Still quiet and smooth
@CLINTHIMSELF1086 Жыл бұрын
Still working 2 years after this comment?
@larryjones77634 жыл бұрын
What’s the name of The garage roll up motor or can u send me the link I would like to buy one on eBay as well and thanks for the video
@huntah2k4 жыл бұрын
www.ebay.com/itm/183037437369
@joshwebster13893 жыл бұрын
Off the subject but what did you use for insulation in the ceiling...I have one of the carport garages as well.....thank you
@huntah2k3 жыл бұрын
4 x 8 Fiberglass foam board 2 inch
@johnwelch20843 жыл бұрын
Josh are you talking about the big gap between the door when it is all the way down. My Carolina Carports shop had this. I can send you a picture of how I filled this gap in to keep heat or A/C in if you want me to?
@reriley753 жыл бұрын
@@johnwelch2084 How did you fill the gap above your doors?
@colomacountry4 жыл бұрын
What model garage door is this..Janus? It appears some don't have a very long driveshaft/axle whereas yours does. Also, the brackets change a lot between models. I'm going to look at mine today. Thx for the vid!
@huntah2k4 жыл бұрын
I'm not sure what model off the top of my head this is but the metal rod i butt welded an extension to it so this would work
@34dawgsgo3 жыл бұрын
Silly question. Interested in metal garages with rollup doors. That metal mounting bracket you made did the mounting bolts have to go through to the outside? Thanks.
@huntah2k3 жыл бұрын
No i just used extra stock and bolted to the inside of the tube
@34dawgsgo3 жыл бұрын
@@huntah2k thanks. Great design. Hard to cost justify traditional doors for these buildings and all the space you save.
@makojuicedaniel93072 жыл бұрын
Do these lock the door?
@huntah2k2 жыл бұрын
Yes. You cant manually open the door unles you pull the cable
@davepardi8494 жыл бұрын
Hi everyone I need some help. I just finished installing my opener like this one and having trouble setting it up. When I go through the setup I set the down where I want it to stop then push set. I then put it up to where I want it to stop and push set. But then when I push the button for it to go down it only goes like an inch and then stops. If I disengage the clutch and lower the door then re engage the clutch and push open button it goes up nice. Driving me nuts. Any ideas. Thanks
@huntah2k4 жыл бұрын
Hmm are you sure its telling you to set bottom first? This one i had to set where i wanted bottom first then set the top
@davepardi8494 жыл бұрын
@@huntah2k Yes I just tried it again. It tells you to set down first and then up. Up works great. Down only moves about an inch when you press the down button
@huntah2k4 жыл бұрын
Maybe a faulty motor.. or something stuck inside it
@duanecalhoon33223 жыл бұрын
Did you figure it out? Setting mine up tomorrow hopefully
@davepardi8494 жыл бұрын
Does anyone know if that is a right side opener or a left side opener or if it matters. Thanks
@huntah2k4 жыл бұрын
You can program it to open / close on eitherside
@davepardi8494 жыл бұрын
@@huntah2k Thanks
@ATacticalG3 жыл бұрын
what is it called
@timd55974 жыл бұрын
Did you need to extend the shaft if so what did you use? Thanks
@huntah2k4 жыл бұрын
I welded a 6" long pipe on the end to extend it
@duanecalhoon33223 жыл бұрын
I had a friend with a lathe turn down a pipe so it slips in but is flush with the original shaft, then spot welded around the joint
@taylorlindsay126211 ай бұрын
What is the outside diameter of the shaft? I’m looking to just slide a larger pipe around the original one but want to make sure it will fit in the u bolt.
@timd559711 ай бұрын
@@taylorlindsay1262 I really don't know the outside diameter of the shift I cannot see that anymore. Looking online the hole through the garage door opener is 1.6 inches that will be the max. Also my friend put up a garage with roll up doors from different manufacturer I remember his shaft had different dimensions than mine.
@timd55974 жыл бұрын
Did you butt weld joint extension pipe or is it slip over pipe?
@huntah2k4 жыл бұрын
Butt welded a pipe right to the end of it
@timd55974 жыл бұрын
I was told no opener will work on my doors but seems good on yours.
@huntah2k4 жыл бұрын
@@timd5597 yea ive had this over a year opening and closing it every day had no problems. Just had to rig it up a little. They still sell this one ebay $120.
@timd55974 жыл бұрын
@@huntah2k I will buy one but not sure I probably will need to make holes in my drum to insert motor 2 drive fingers .
@timd55974 жыл бұрын
If you don't mind I would appreciate a call 6105040954 I have question on the hub of your garage door thanks Tim.
@davepardi8494 жыл бұрын
Does anyone know if there is a wireless keypad that will work with this opener
@davepardi8493 жыл бұрын
@@reliableroofersinc5551 One of the sellers on eBay told me there’s one that works but I can’t figure out how to put the link in here to it. If you wanna give me your email I’ll try to send you the link.You can send it to my email at dapa52@gmail.com. I am not really sure if it works or not because I didn’t purchase one
Yes so far. Ivebeen using it everday for over a year still just as quiet and smooth as it was
@HazzNJayza4 ай бұрын
Is it still working?
@timd55974 жыл бұрын
Thanks!!!
@janiceturner820210 ай бұрын
Need to set remote having trouble
@CD-hc5ds2 жыл бұрын
2 year update??
@huntah2k2 жыл бұрын
Had 0 issues with this. Still works great. No complaints
@toddjacobs56609 ай бұрын
Yr rite those instructions suck ass! And thats why you never said anything else about adjustment, i reccomend no one buys one of these junk things, i bought one made a bracket to move it out welded a pc of pipe on the end, all of that was great, i just dont know how to adjust it, very generic and complete junk quality !!!