Checking and Setting Ride Height // HOW-TO VIDEO

[@surfntchr]

Added the dual rate to myXP1000 made a night and day difference. Had you re-valve/and rebuild and it's even better!

[@ShockTherapyllc]

Hell ya! 🤘🏻

[@radiolotek]

You should show a tire size to height chart to make it easy. Also, is there a video to set up the crossover collar? I got a set of your springs and need to put them on. I'm excited to see the difference. 2021 X3 max RR

[@ShockTherapyllc]

In general, rear crossover will be 2” above spring divider and front at 1”. But check the video for your specific vehicle.

[@claudiufilip3463]

hello, I'm from Romania and I have a Maverick x3 xrc rr 2021 and I want to prepare the suspension from general settings to macadam speed competition settings on snow, could you help me with advice for adequate adjustment for speed on rough terrain?

[@planb8520]

Hey guys great explanation.👌 Is this method of using tire size a good rule of thumb for other vehicles? eg ranger/silverado desert truck?

[@ShockTherapyllc]

Yes. Works for everything.

[@ssantac]

Thanks for the vids, I'm learning a lot! Do you happen to have the ride height for a Can Am Defender? If it matters its an 18 HD10 max XT

[@ShockTherapyllc]

13.5-14” stock tires. Add 1/2” ride height for every extra inch of tire over stock

[@JDHarpr]

A rzr pro xp with 32" tires. Where do you want the ride height at? What number do you start with? The height listed from the factory?

[@ShockTherapyllc]

16” front. 15.5 rear with you in it. 👍🏼

[@ddipalermo]

Should you measure off the tires for polaris as well to determine ride height?

[@aaronchamberlain1638]

yes

[@unitymixer]

Wait, what? . The cross-over locknut should be 2 inch upper the spring dividers ?

[@ShockTherapyllc]

Every spring kit and UTV can be slightly different. Check your car specific settings but in general 2” rear 1” front is a good starting point.

[@fernandorivera8663]

I have a Turbo S with ur sprint kit. Can i adjust height with coilovers on the car?

[@ShockTherapyllc]

Absolutely you can. Easier if you Jack the car up. 👍🏼

[@russellcorcoran2231]

I watch a lot of videos, and I still don't think I did it right. I have 8in between the springs in the rear end. They seem really tight. I read that was factory recommended. What is your recommendation?

[@ShockTherapyllc]

Email us your specs and or pictures of your setup to [e-mail] so we can see what needs to be adjusted.

[@bretroukema]

What spring compressor are you using with the shocks still installed when you are doing the pre-load adjustment?

[@ShockTherapyllc]

Jack tech. Amazon🤘🏻

[@JohnnyMoseley]

@@ShockTherapyllc Can you confirm this. I have the Jacktech 3500 but your using a compressor without removing the spring and it looks like its only one side of spring vs the normal 2 piece design you see for sale. What model number compressor did you use on spring without removing it from buggy?

[@ShockTherapyllc]

@@JohnnyMoseleyhere is the smaller one we use a.co/d/6hq7pgp

[@JohnnyMoseley]

@@ShockTherapyllc Thanks. Exactly what I was looking for.

[@Degen.Diesel]

What kind of ride hight should i shoot for on a 23 yxz with 32s

[@ShockTherapyllc]

15” or so. 🤘🏻

[@FreedomIsntFree2023]

So 16.5" ride height in the rear with four grown men in the car?? Really curious what the height is without the guys in the car......I bet that thing looks like a "monster truck".....

[@ShockTherapyllc]

With no riders it's going to sit pretty tall, we always set ride heights loaded with gear and passengers so it's correct when your riding.