Chevy C10 Air Ride Install | Rear Part 2 | KP Components Notch

Simple.C10's vision is to encourage and empower the C10 community by offering parts, resources, and DIY videos. For a step-by-step guide to bagging your C10, check out the tutorials section of my website! www.simplec10.co
Here are a few things that the new website offers (www.simplec10.co)
→ Exclusive Parts for your C10.
→ DIY Tutorials, including my step-by-step "Air Ride Guide".
→ Links to all my favorite C10 parts with reviews!
→ Build Profiles for all my past builds.
→ Simple.C10 Merchandise.
Thank you for your support and encouragement!
→ Become a Simple.C10 Subscriber!
→ Website: www.simplec10.co
→ Instagram: / simple.c10
→ Facebook: / simplec10
→ My Channel Home Page: @simple.c10
→ As an eBay/Amazon Associate, I earn from qualifying purchases.
If the video was helpful, remember to give it a "thumbs up" and consider subscribing.

[@Nizzwell]

Love it ,doing our 79 c10 soon great channel ✊

[@SIMPLE.C10]

Thanks so much!

[@SIMPLE.C10]

Thanks for watching! Please hit the subscribe button to see all my new videos when I post them.

[@RADIKAL92]

Loving the videos. Keep up the good work.

[@SIMPLE.C10]

Thanks buddy

[@lifestyleraceing5468]

Where did I get the notch kit can u plz give me link

[@SIMPLE.C10]

I don’t have the link but you can type in CA Chassisworks and go to their suspension section.

[@lifestyleraceing5468]

@@SIMPLE.C10 thank bro

[@davidbrown5689]

how big of a notch is it, i did one on my 66 c10 but didnt go as low as i wanted thinking of grabbing that one

[@SIMPLE.C10]

It’s a 9 inch notch.

[@michaelmichels5168]

such a helpful video!! I have a 63 c20 pretty much same frame but over there's two steel plates over the rear axle on the inside.. I'm thinking this will fit since it bolts to the outside of the frame.. same frame as the C10 but the insides a Little beefed . I think if anything I might just need a little bit longer hardware on the bottom if there is

[@SIMPLE.C10]

I’m not positive but you could send photos to my Instagram simple.c10s

[@josetijero471]

First off thanks for making these videos. I’m about to install my step notch from Kp. How did you route the brake lines?

[@SIMPLE.C10]

I reused all the factory stuff basically. You can check out how I did black dice. I redid all the rear end lines.

[@huskydevil333]

Thanks for the helpful tips and great job on your trucks. I have a '61 Apache and i'm building most of my components, since their is almost no aftermarket parts for my year, so i was wondering what are those bolts that you used to mount the bags to the brackets and what did you use for the intake hole on the bag?

[@SIMPLE.C10]

The bolts are just 3/8 inch grade 8 bolts with washers and lock washers. I used a 90 degree push fitting.

[@huskydevil333]

@@SIMPLE.C10 Thanks. I thought I saw some kind of specialized fittings at first. I really appreciate the videos you're putting out. I've been looking for someone to explain the step by step process. Please keep up the great work.

[@SIMPLE.C10]

Thank you

[@bjhuisingh2211]

I'm interested in a low stance but want to save as much of my truck bed as possible. I don't want to do a 4 link. I want to use the stock trailing arms. How many inches of extra space are in this step notch set up? Could I weld in a shorter step notch and get the same height but have a deeper truck bed? Thanks for sharing!

[@SIMPLE.C10]

Yes, if you can weld, you can do a smaller notch and get about 4 more inches of bed room. You can do this exact setup without the kp components step notch. I only use it because I’ve done it before and I don’t have a welder or the skill to do it any other way.

[@SIMPLE.C10]

You could go with a basic bolt in notch and get really low and not loose any of your bed floor but it just isn’t low enough for me.

[@bjhuisingh2211]

@@SIMPLE.C10 I like what you did with the front end. both with the cupped LCAs and the aftermarket control arms. I would like to copy that and then get the rear to sit level without wasting any of the bed space. Your vids and replies have been very helpful. Thanks!

[@chrisstriby9602]

Do you know if using the bolt in cpp notch that's about 4" of clearance, with the 4" drop blocks and the adjustable panhard bar. It will still be about half inch off the ground or will I need that monster notch?

[@SIMPLE.C10]

The mini notch will not get you close to laying out. A monster notch is 9 inches of clearance. With the bolt in notch and blocks you will be about 4 inches off the ground compared to about an inch with the bigger notch the way mine are bagged. Flash, my red truck, is mini notched.

[@bigal50239]

Two questions, do you add shocks to the rear? And also how is the ride with the set up? Right now my truck rides like a covered wagon. It’s just has drop springs.

[@SIMPLE.C10]

Smooth as butter! Yes. Shocks are really important.

[@bjhuisingh2211]

I did not notice in previous videos. Is the "white wall" actually part of the rim painted white?

[@SIMPLE.C10]

Yes! The rim lip is painted white to appear like a white wall. I have pics on my Instagram simple.c10s