Chevy Silverado Winch Bumper Install: Half Idiot's Guide

[@4g63tom4]

Great vid dude! I just bought the same front bumper with winch and this was the best step by step ive seen especially including the flaws you encountered 👌🏼👍🏼

[@ChurchieShed]

🤘🏼

[@johnnybbyl1626]

Great job buddy,...gives me confidence to install my newly purchased RC hidden winch bumper, however it looks like it could be a bit of a job. Mine did come with the two side fog lamps as well for a spanking $480.00 out the door. looks great on the truck. Love your 1/2 " torch wrench, probably gonna have to get me one. Time to Wrench..!!!

[@AriePharmD]

Excellent content. End result is amazing. I’ve always liked the RC hidden winch mount for 2019+ Silverados.

[@bilmanderson2882]

Good Video, like how you show the little touches to make a neat job.. cutting the trim to make it look factory.. well done

[@ChurchieShed]

Thank you! Much appreciated.

[@benjamincrooker2533]

Nice video. Looks like a cordless winch control might be in your near future. Especially right after you get stuck in the mud and Kent crawl under the water to Plug in the controller. Lol.

[@ChurchieShed]

?Exactly! Do you have one installed? Anything you'd recommend

[@benjamincrooker2533]

@@ChurchieShed I saw quite a few different ones being used on different winches on KZbin videos. So I would suggest that you just type in your size and brand of winch with wireless remote control review. Good luck man.

[@BarryDavis-sv6nz]

AWSOME VIDEO

[@dustinherring4146]

It’s insane you have to take all that off just to remove the fascia

[@RST2123]

Excellent mo it’s time to order mine

[@elicarrillo632]

What kind of lift you got on your truck?

[@marlonshije5595]

This is why I want to trust rc but not so sure. 1st off see how he was able to pick up both housings with fingers. Almost 16th inch steel but steel is how they get you to buy. And second see how the winch tray didn't fit. My 3.5 lift from rc for this same model has failed twice. And I have plenty more quality comments I could share but I'm not bashing. Still so undecided only cause I've also seen the fabfour bumbers smash and total these trucks like butter. Miss the obs chevys so outside I go to fix mine back up..

[@dtay0421]

Sick video and truck! What brand fender flares are those?

[@ChurchieShed]

We get asked about the fender flares a lot! 🤘🏼 Here they are… CHEVY SILVERADO FENDER FLARES : Half Idiot's Guide kzbin.info/www/bejne/gXXFZ4l3bdKorM0

[@ChurchieShed]

Super cheap and sorta chinsy but they work ironically

[@Sarzmeenfars]

Will that fit on 23 silverado trail boss ?

[@ChurchieShed]

@@Sarzmeenfars Not sure. I would check directly with Rough Country

[@Biker305_adv]

Great job !! Enjoy it

[@ZekBailey]

Does it not come with the little cube lights for the other spot on the bumper and does it come with the hooks you had on on it too at the end?

[@ChurchieShed]

It does come with the cube lights. We didn’t put them in until later. And yes the hooks are also included.🤘🏼

[@fsoverlanding]

Question, can you put a Harbor freight Badlands winch on that plate?

[@ChurchieShed]

I don't see why not. As long as it has that same 4 bolt pattern on the bottom to fasten it to the bumper, it should fit. There's a ton of room up behind that bumper... fyi I'm saying "should" fit without actually doing it... maybe someone else out there has a Badlands in this bumper to confirm?...

[@fsoverlanding]

Thank you ma'dude

[@RST2123]

Do u still have your facia bumper I’m interested in buying it

[@ChurchieShed]

Unfortunately not. Gave it away already. Sorry.

[@carlosantoniolopezchavez4615]

Have you had any problems I was told not to wire my winch to the littlelfuse section

[@ChurchieShed]

So far no problems, but we'll keep that in mind. Thanks for the heads up.

[@joshuagosney6614]

Amazing bro.

[@chrismcalexander8318]

Will it fit on a 21 1500 custom with 2.7 turbo?

[@ChurchieShed]

I would assume so. Since you have a 21 1500 I don't thing the motor makes a difference in the front bumper configuration. But I'd definitely double check with Rough Country to confirm.

[@chrismcalexander8318]

Maybe interfere with intercooler?

[@EvanWidowMakerHenshaw]

What size winch were you using here?

[@ChurchieShed]

Warn 8500

[@culturediecast.]

Where did you get the flares

[@ChurchieShed]

Super cheap off Amazon. They just stick on. Not high quality but they look decent.

[@culturediecast.]

@@ChurchieShed I saw on your other videos where you replied my bad but thanks for getting back to me, Also how did you attach them to the front wheel well not much surface area compared to the rear I like the look.

[@adamwest3637]

How did you get the winch tray to fit? Can you reuse the oem fog lights? They look like the same shape as the new bumper.

[@ChurchieShed]

The winch tray comes with it so it's designed to fit... I think that's what you are asking. As far as using OEM lights, I'm not sure. Ours was a "Custom" Trail boss so did't come with factory lights. There is a pretty specific bracket and mounting locations that come with the RC lights, so I'm not sure it would work with OEMs. We will be doing a vid on installing the RC fog lights ASAP

[@jaybird1987]

What type of fender flares are those? Im looking for similar ones. My 35s stick out a lot but dont want massive ones as i like them sticking out a bit and want a little protection.

[@ChurchieShed]

They seem cheap but they really stay on there. It's these: amzn.to/3UL18KW

[@jaybird1987]

@ChurchieShed Thank you! Also, great video on bumper install. I want a winch but want it hidden also.