Chiller 30Gx main oil filter & compressor oil filter changing

Music: www.bensound.com

[@kamalsubramanian4003]

உழைப்பே உயர்வு ❤❤❤

[@jnethin]

Very good

[@jishobpkozhikode8847]

Good job.. .maneesh

[@sinthamathar9272]

nice bro ......i love it video

[@ziaarnie3694]

Content is nice brother , please try to explain each process that would be very beneficial for viewers. Thanks

[@GalaXy808]

AMAZING VIDEO THANKS!! DO YOU HAVE A VIDEO HOW TO CHARGE OIL

[@matiasdimaurizio]

you have to close a key to change the compressor oil filter,?? thank you from argentina 

[@AshishKumar-lv7fi]

Great work

[@lancydsouza1326]

Funny thing, since you have connected gauge manifold in back seat of angle valve, why de-pressurise by cracking nut? Just to spill oil all over? When you are going to use gland? It is mandatory to loosen gland nut before operating valve to increase life of lead inside.

[@TechnicalBrainHVAC]

How to connect motor shaft wheel on shaft need to heatup or any other trick

[@cooltechhvac4555]

Hydrolic press

[@manoharkattula3182]

Hi brother after vacume this filter replaced before replced pls reply

[@cooltechhvac4555]

Need to vacuum after Replacement

[@prithwishdey6708]

#sir please one video make on hvac compressor part winding star cannection.

[@ginna568]

Great job

[@guddukryadav7507]

Very nice video sir plazz aur bhi video daliye i am wating...

[@cooltechhvac4555]

yes please

[@AkramAli-78655]

Dear brother what is the name of the device that is installed left side of the oil filter and oil pump in oil separator tank. Pls let me know. And why there's a bypass open line beside the oil pump. What is the use of this line if already the is one line in which oil pump is installed.

[@cooltechhvac4555]

That was a oil differential switch

[@cooltechhvac4555]

When the chiller starts, first Oil pump work and build oil pressure, there is a non return valve on right side. It will block oil to oil separator when the oil pump works,. Once chiller start the pump will off and oil will pump with discharge pressure through the bypass line ( non return valve)

[@cooltechhvac4555]

Thanks for the comments

[@abdulkadirabdul8516]

Sir g mere site pe 30xa model ka carrier screw chiller hai. Isme bar bar low pressure alarm aa raha hai. Kya kru.

[@cooltechhvac4555]

Did you check the pressure with a gauge?

[@cooltechhvac4555]

Please check suction pressure with a gauge.

[@abdulkadirabdul8516]

Low oil pressure alarm aa raha hai bhai

[@cooltechhvac4555]

Reason 1 Low oil level 2 Gas shortage 3 Main oil filter chocked 4 Chocked internal oil filter 5 Check oil solenoid

[@prithwishdey6708]

Why cheeler at first unloading then compressor running.

[@cooltechhvac4555]

Reason is to reduce the starting load

[@w___6711]

What are the reasons for changing the oil filter?

[@cooltechhvac4555]

Pressure dropped across the filter

[@cooltechhvac4555]

Oil testing kit is available

[@giyasuddinmallick7493]

Good job

[@simplehuman1771]

How to up the oil in screw compressor 30xa model

[@cooltechhvac4555]

Topup to oil separator

[@cooltechhvac4555]

Turned off the chiller, you can top up by hand pump through the discharge pressure transducer pin valve to oil separator

[@ismailahmed8031]

v.nice

[@ImranMohd-xs4uw]

Coming alarm high oil filter drop , what Is this problem

[@cooltechhvac4555]

What alarm code showing in the display 62, 63, 64 or 65??

[@ImranMohd-xs4uw]

@@cooltechhvac4555 30xa carrier chiller ,coming same alarm high oil filter pressure drop, this chiller no have any code

[@dalalmanjit4463]

Model of oil top up pump ?

[@dalalmanjit4463]

Please tell me the oil top up pump model ?

[@cooltechhvac4555]

I'm using manual hand pump

[@cooltechhvac4555]

For top up oil

[@cooltechhvac4555]

Oil Pump YJ _ Yellow Jack 77940. UPC No. 686800

[@dalalmanjit4463]

@@cooltechhvac4555 thanks sir

[@guddukryadav7507]

Sir mai bhi new techanician hu mai bhi dubai me hu mera siniyar kuchh bata ta nahi hai jab kuchh change karna hota hai chiller me to edhar udhar bhej deta hai .hamko plazz aap help kijiye mai aapka video dekh kar kuchh sikh pa u

[@harishansari6039]

kzbin.info/www/bejne/r6WwYXiOaaadgpI👈👈👆👆😀😀

[@ManojGupta-sz7yk]

The main question is how you know oil filter need to be change?

[@cooltechhvac4555]

kzbin.info/www/bejne/mqmynWOsac-io6M

[@cooltechhvac4555]

Compressor Winding burns and terminal also. Long time shut down without gas.

[@cooltechhvac4555]

All gas drain through the burned terminal

[@mdfaheemuddin5816]

ur not a professional technician

[@brucecrutchfield3473]

Why is he not a professional technician?

[@lancydsouza1326]

@@brucecrutchfield3473, 1) he operated angle valve without operating gland nut which may destroy lead inside gland nut causing leakage and leaving black stains on valve stem. 2) he de-pressurised isolated filter even though he had gauge manifold connected on backseat of angle valve spilling oil all over and leaving oil stains every where near by. 3) Doesn't look like he replaced '0' ring on internal filter cap. Looks like managed with old compressed ring.

[@cooltechhvac4555]

Thank you

[@shaikhirfanali9677]

Very good