Chinese 'Foredom' SR Series' 230 Volt 1/6 HP Motor Flexible Shaft power Tool

[@SteveJordan]

facebook.com/steve.jordan.3766952

[@ErnieKolep]

Thanks

[@MattysWorkshop]

Gday Steve, I’ve recently brought the Dremel 3000, I’m impressed with it but it does lack in the power/torque department, if I’m polishing with it I have to be careful to keep the same pressure at all times so I keep a even finish due to the lack of torque, it does struggle in quite a few things I’ve used it for, I wish knew about the one you have before hand, after seeing you demonstrate yours I would have got the same, then again I still might talk the wife into opening the purse strings once again with a little sweet talking, only time will tell, Thanks mate for a great honest review it’s much appreciated, Cheers Matty

[@clivemilner]

China manufacturers products for Europe and USA. One gets run ons, when they make extra products. This maybe such a case.. Mine has been great. Servers my needs.😊

[@olegpetelevitch4443]

Just got mine and the H15 hammer , H20 it came with kit also H10 and the H30 ! Thank you top info !

[@madisonhill3175]

This comment section is quite a cross-section...you’ve got Foredom employees leaving comments about how bad this tool is and how in 2020 you may not receive the item in the mail because “China”. Then you’ve got people knocking it for being bad and then admitting to rebuying it after it breaks. Then the icing on the cake is the updated comment telling us you never knew it was a fake even though it was 1/3 the price of the original. And that we shouldn’t buy this based on principle. Then, drum roll please, you tell us it’s a great value for those who can’t afford the original. Holy shi t. Make up your minds.

[@luisgomez385]

I know right.

[@swiss300173]

I know, I’ve took a chance and ordered one. 😎

[@muhammadc2000]

My friend bought one. We used to use foredoms back in college. He told me they are pretty good and perform the same

[@SteveJordan]

Mine is still working fine. I think the Chinese ones are excellent.

[@BigHenFor]

If the original Foredoms are as good as their reputation, then starting in the jewellery or engineering trade buy an original American Foredom. Why? They were over-engineered and have reliable and long lasting motors. Time is money in the jewellery trade so having reliable ones that can stand 40 hours+ a week use is essential. Ones from the 1970s are still in circulation and can be bought fairly cheaply, at least in the US. At most you'll have to replace the carbon bushes. For everyone else - occasional users and hobbyists - a Chinese knock-off may be more cost-effective as the price difference is huge at 2/rds less than the equivalent original. What I do note is that the Chinese Foredoms have poor foot pedals. That's where the cost cutting is very apparent. If speed control is important, the Chinese ones will not suit. However, as an aside, I do note that the Chinese Die Cutters on Amazon may be a better option for occasional users as they are cheaper still. No foot pedal, but come with a flex shaft and are claimed to run at speeds between 8000 and 30000 rpm. They can take from between 2.3mm and 6mm bits. Downsides? Flexibility. They don't use the Foredom style handpiece, so one is limited to the type sold with them but, these do everything but carving. At under 50 GBP, they are good value, and avoid any moral questions. Take your pick. Not everyone has over 300 GBP to drop on an original Foredom sadly.

[@morganlewis2667]

I had one delivered from China yesterday after a 2 1/2 month wait. It would not turn on its own power. I took the flex shaft off to rotate manually and found that it was hanging up internally. Took it apart and found where the armature was contacting the stator and hanging up. After filing that area down it ran smoothly. Next I filed and sanded the bail handle hanger which had horrible burs all around both sides. The control pedal is basically on/off but feels like it should regulate. I'll change that out. The flex had what may have been a little graphite or just grime from production I lubed it with lithium grease. I've bought a lot of tools and parts from China, some I'm pleased with, some that needed some help like this. For the price I can't complain TOO much and think it may serve well now.

[@clockguy2]

When I was a jeweler, we had to change the bits quite often. the one slot to insert the chuck key gets annoying. We would take a jeweler's saw and cut back the aluminum shield from the chuck so the key can be put in at any position. Also we would get a chuck key without the plastic handle. Since the motor is often hung, we would tape the wings of the key to the power cord hanging down so you never have to hunt for the chuck key.

[@SteveJordan]

Hi yes I have another similar handle that I turned back like that to expose the chuck key area. It is much better like that.

[@felixf5211]

I own 2 of these tools. Love them! One thing I'd suggest is upgrading the pedal to the (genuine) Foredom. A night and day difference in control. BTW, I'm in the US and both of mine have red labels. The real ones are blue and the switch is configured the opposite way.

[@angusdafoe9351]

Foredom do a red label machine it's a 230 volt international model.

[@kingboymachine7329]

​@@angusdafoe9351 yes but this machine is still fake. the price is 3 times cheaper than the real price of the foredom sr with the blue label. and it is made in china. I just bought it yesterday. but it is still good and can compete with the original foredom

[@armandine2]

I haven't read all the comments but it looks like the China copy may not have the alternative holes for the bench mount Yoke - can anyone confirm this observation?

[@BossBear01]

So it been over a year now can you say it as good today as it was then.??

[@SteveJordan]

IMPORTANT UPDATE:- PLEASE NOTE THAT THESE TOOLS ARE COPIES OF THE RENOWNED FOREDOM USA TOOL AND ARE ACTUALLY MADE IN CHINA. I NEVER KNEW THAT AT THE TIME OF MAKING THIS VIDEO. DO NOT BUY THIS TOOL IF YOU WANT A GENUINE USA FOREDOM, WHICH ARE CONSIDERABLY MORE EXPENSIVE TO BUY. HAVING SAID THAT THOUGH, I AM REALLY PLEASED WITH THIS COPY. IT IS REALLY WELL MADE AND RUNS REALLY SMOOTH. I THINK IT'S THE BEST ROTARY TOOL AVAILABLE IF ONE CANNOT AFFORD A USA MADE FOREDOM.

[@pearlettoi2046]

Does Foredom USA make a 220v version?

[@albertoromero214]

@@pearlettoi2046 Yes !.

[@MrDoomcrust]

How’s this machine holding up?

[@coreymerrill3257]

So this is the Chinese copy of the fordom s-r? Are these able to use all of the real fordom accessories and replacement parts? Will I need better motor brushes ? Does the foot pedal have good sensitivity ? And can it cut wet ? I need a flexshaft grinder and am broke as joke until I can get some things made...and some Rubyvale sapphire rough, skin polished.

[@DavidGellPainter]

I agree that if it's not a genuine Foredom, it should not be advertised and labelled as such. Let it be Chinese designed and branded and sink or swim on its own merits. Please check that the in-line connector plug between the foot pedal and motor is the shielded type IEC C14 or similar. The connectors on mine are unshielded, leaving potentially live contact pins exposed if the plugs become partially separated during use. The 3-pin mains plug also appears not to be fused. I believe the unshielded inline connecters are for a DC motor version, but have been used with an AC motor. Post Brexit, I'm hoping the UK can have more amicable trade arrangements with the US, so we can purchase quality, genuine US products at more affordable prices. Chinese competition is fine, but please, no copying and potentially dangerous goods to the market.

[@flair4crafts894]

What kind of of circular blades do I use for cutting split rings from electric coper wire?

[@SteveJordan]

Just HSS ones will be fine. Regards Steve

[@flair4crafts894]

@@SteveJordan Thanks

[@MetalMutant]

I want to polish my 76 rd crankcase, so I bought this UK version, didn't know it was a KO, i never thought the real deal would be $270+, since i compared it with dremmel 4000 price range, bought mine for $100+.

[@Liflowcbd]

I just got mine from China after a six week wait so this video is super timely for me. I knew it was a knock off but it was a risk I had to take. Now I just need a stand that's not £ 45

[@SteveJordan]

I'm really pleased with mine. It is totally excellent in its build and is a pleasure to use. I have just bought one of the Chinese special handles for it. Its a slim one with a lever on the side to quickly open and close the chuck. Personally even If I had the money to buy a genuine Foredom. I would still buy the Chinese knock off. Its such great value for money.

[@Liflowcbd]

@@SteveJordan What are you using for a stand? I am thinking of buying the quick release hand piece for convenience also but I believe it only takes 3.25 mm

[@SteveJordan]

At the moment I have it hanging from the low ceiling but I was thinking of getting or making the stand. That handle does only take that size bits but it's a nice accessorie for the price

[@gavauls]

Just buy a hanging basket bracket, screw to wall, hang from end, job done!!

[@felixf5211]

I screwed large-ish hooks into the wall that sits against the bench and hung all my flexshafts. Obviously, one per hook. Works great. I also own a Chinese quick change wand. No problems, just convenience.

[@mariodiaz4694]

They look the same hope they perform the same ,also foredom have a 220 v looking the same ,that’s what I have in the Philippines the original they sell here in the USA ,some say looking at them side to side you won’t know the difference not until you used it 😊😊 for a couple of hours or more

[@ForedomElectricCo]

It is a knock off. It is not one of ours. Buyer beware. No warranty. No replacement parts.

[@griffiths-handmade-knives]

Foredom Electric Co. really? Cheeky bastards put your company name all over it! Did this guy edit the title of the video after finding this out from you? In the video he seems clueless, and now it’s saying it’s a ‘Chinese,’ Foredom 😂🤣

[@SteveJordan]

@@griffiths-handmade-knives My Chinese one is still working perfectly. It's a great tool.

[@pootieputin2771]

@@SteveJordan Why did you claim yours was an actual Foredam...made in the US??? You clown.

[@petertdav]

hi, do you still have this? is it still working? thanks

[@SteveJordan]

H Peter, I sold some time ago. It was a very good tool, but I found it too cumbersome for my small workshop. I prefer the handheld Dremel type rotary tools. Regards Steve

[@shawnmlopez5125]

Excellent video. Question: does the 6mm chuck go down to 0 when closed all the way?

[@SteveJordan]

Hi Shawn, Thanks...Yes it does.

[@shawnmlopez5125]

@@SteveJordan Thank you, sir!

[@constantinb.9713]

With waht do you hang the motor ? And Do you also look above the engine while it's running and there are sparks?

[@lbdeuce]

ummmm maybe a sting... or anything offering more rigidity than jello... what kind of a question is this? how is it that you need the utility a tool of this nature but you lack the inclination to understand how to support it? seems similar to procuring a graphing calculator and asking how to add 3 to 1.

[@RagsdaleCreek]

Nice video. Watching in Alabama!

[@DeuSJaguaR]

So, is it much better to get the one with the blue label? (USA model) it's a bit more expensive than this one but what do you think? Anybody? Saw this same. Model on ebay for around 90, all attachments and real cool and pro but, is it worth it? Thx in advance! :)

[@mariodiaz4694]

They still have 230v red labeled and made in Bethel USA not like this one made in China

[@kayartist]

hi steve , so its been 3 years since you purchased this power tool. Can you say how long it lasted? before it broke, if at att it did. thanks for the video.

[@SteveJordan]

Hi, I don't know as I sold it. I prefer handheld dremel type tools rather than these.

[@petertdav]

@@SteveJordan how long did you have it before you sold it?

[@SteveJordan]

It must have been a year or more. I never had any problems with it. I just found it a bit cumbersome for my small workshop. I prefer the Dremel rotary tool type. Regards Steve

[@stivi8625]

Hi - new to this interest and would love to know benefits of different size Foredom - which is best 4mm or 6mm , seriously thinking of buying one.

[@petertdav]

hi sorry for the delay in replying, i was taking a dump. Anyway to answer your question, i have idea.

[@lucacolonnesi]

Nice video Steve; i tihink that some counterfeit chinese articles can work good and some others just don't. there is a percentage of risk on buyn those items. some years ago i bought , in example a Little Torch by Smith in a qualified goldsmith shop in Naples paying it about a half of its price (120€). after a week, and after dismounting the torch, i realized tha, probably i was cheated, but the torch works fine, even if,, buying it directly in china, i could have paid significantly less...sorry for my "rusty english". ;)

[@derekwilkinson7939]

Does the shaft require any lubrication?

[@SteveJordan]

Yes it does. You can use the Foredom lubrication, but I just use a light coating of Molybdenum Disulphide grease. I forgot to mention it, but there is an important section on lubrication in the users manual.

[@SteveJordan]

SEE TOOL LINKS BELOW:- FOREDOM 220V 0~18000rpm 6mm Hanging Flex Shaft SR Motor -- bit.ly/2S78i8t 20pcs Stainless Steel Wire Wheel Brush Cleaner Polishing Rotary Tool24pcs Wire Steel Brass Brushes Set Polishing Brush Wheels -- goo.gl/UY2ZK9 32pcs Brass Steel Wire Polishing Brushes Set Polishing Wheels Kit -- goo.gl/j5FKDA -- goo.gl/XRNALh $0.01 Snatch -- bit.ly/2NuPYVW Spring Sale -- bit.ly/2VzASRP Electronic Tools Sale -- bit.ly/2SLxUYG

[@SteveJordan]

Banggood Health Protection -- bit.ly/33tNTBx Banggood Health&Care Protection -- bit.ly/3d7QpSy

[@katyb415]

You are lucky your Chinese Foredom works, mine broke after a week of very light use! I am never going to be able to return it - so now I have to buy a new one... Buyer beware!!

[@28gwdavies]

Hi Steve, a shot in the dark here... Do you know if the Banggood SANOU K72 Lathe Chuck 125mm 4 Jaw independent will fit on a Chinese mini lathe 7" x 14"? Sorry to bother you with this but you are the best person to ask.

[@SteveJordan]

Hi Glyn Yes I use this one on my 7 x 14 lathe, but you need to make or buy a backplate for it. Arceurotrade may still sell the backplates.

[@28gwdavies]

@@SteveJordan Thank you Steve, I'll have to buy the chuck and then figure out which backplate I need from Arceurotrade, give Rosie a worm for me...

[@ianrichardson3329]

can i ask if you have any problems with this chinese tool since you bought it? i'm looking at buying one but wondered if its going to last

[@SteveJordan]

No I haven't had any problems whatsoever. It's a fantastic piece of equipment. A high quality tool.

[@morganlewis2667]

@@SteveJordan But like I said in my long comment, mine wouldn't start when it came....however, I fixed it because I've been doing such for 50 years. It is based on a good design. It all depends on which chinese peasants or children are working on the one you get.

[@MrMittens1974]

For sure it's a Chinese counterfeit if it's on Banggood for eighty quid. The problem with these is the risk of malfunction with no warranty or support. You have to pay the postage to ship it back to China then they try to weasal out of replacing by saying there was user damage not covered by them.I think in the UK Cookson sell the real deal for £200 with a 2 year warranty.

[@jeremydemarco8697]

I got mine from Amazon prime for 109 buck, very solid, very smooth, not hot at all

[@ianbrown1474]

I’m a little confused - is it an original foredom or a chinese product? what is the name of the site where you say you say you bought

[@SteveJordan]

Hi It is a Chinese product. They sell them on many sites though even on eBay so I presume the company don't mind for one reason or another? eBay would be the first to remove such listings if it contradicted any law. It's the same with Mitutoyo Calipers. You can buy copies dead cheap on eBay and they are never removed from the site. eBay is very strict on this sort of thing, so I do not know why they allow it. I'm really pleased with mine. If I had the spare finance I would have bought a genuine one, because then it keeps it's value if one re-sells such things. If I sold this one I would have to specify it was a copy. Regards Steve

[@ianbrown1474]

Steve Jordan thanks for clarifying. I guess there are two issues: (1) is the tool any good? - sounds like it is (2) is it ok to write Foredom’s US address all over a product (presumably for warranty) that Foredom made no money on. I have absolutely no problem with quality chinese products but I was slightly thrown that you made such an effort to describe the logo’s, addresses and brand when it apparently isn’t a Foredom.... unless these ARE Foredom (grey) imports manufactured for Foredom in China then the point of the brand/logo is lost on me though I *was* very interested in your hands on experience of the tool itself. Hope this doesn’t comes off as a rant but you mystified me there for a while - great review though - thanks :)

[@felixf5211]

@@ianbrown1474 I own 2 of these tools. They're fantastic. Even though one came with a warranty card, I wouldn't suggest contacting Foredom. These are counterfits; they were not made by Foredom.

[@guidelineuk]

Hi is still working....😎???

[@SteveJordan]

Hi yes it is fine. A really good piece of kit.

[@guidelineuk]

@@SteveJordan thanks for the quick reply Steve really can't afford the real deal so I'm going to take a chance at this I will let you know how I get on thanks again 😎. Will like and subscribe

[@guidelineuk]

@@SteveJordan I've got it. it looks pretty decent .. did a screw knob bolt mod to the foot controller to turn into speed controller

[@TReischl1]

I know I am late to this party, but. . . . Foredom's are not "all that". Bought one about 20 years ago (keep reading), used it a total of maybe 30 hours run time. The switch went belly up. Called Foredom, told me that getting it repaired would cost more than a new one. So they sent me a switch. Holy smokes! Trying to remove and re-solder that switch is pretty much impossible for a mere mortal like me. So do NOT yammer to me about "warranties" and "made in the USA" ad nauseam. I am much happier with my $79 chinese one. Mainly because when it breaks I will not be out over $300. Made in the USA is way, WAY overrated these days.

[@creandoCOSASdiy]

Does it still work? Do you have the same opinion of this Chinese clone tool to this day? I'm thinking of getting one for stone carving, I'm not sure if it will die in a few months of use.

[@SteveJordan]

Mine still works perfectly It is my best rotary tool. I think they are brilliantly made even if it is a copy.

[@Usucito]

@@SteveJordan Thank you, i appreciate your response. Then i think i'll order one!

[@moonolyth]

Wow, they don't sell a 110volt version to bad for me !... Just got me a leather hand crank sewing machine from Banggood great price 1/2 what on eBay.

[@felixf5211]

Look on AliExpress. That's where I bought mine. 110V.

[@christopherfothergil]

no longer sold on banggood

[@SteveJordan]

Hi yes they must have sold out!

[@steph2211]

That would be a great tool to have in the shop

[@Kimicals123]

Are you using this with an adaptor plug? What size fuse are you using?

[@steph2211]

@@Kimicals123 I didn't purchase this yet you will need to check on banggood site for info

[@моржтюлень-г4ф]

Лучше Foredom только новый Foredom .

[@FlukeTog]

I live in Connecticut think I’ll drive over to foredom one of these days. I’ll keep saving and buying from allied country manufacturers. I don’t want to pay for the rounds that come back later. Save and buy the real deal. It’s always worth it eventually. Fake Rolex bangGood ?

[@davidhaney1394]

dont call it a foredom, its not a foredom . its a cheap knock off . mine died after 10 months . I did buy another one though , when they work they work well.

[@papinl5938]

The American version is to expensive, that’s the only problem.

[@markhatcher8694]

That's if it ever turns up every time I order anything from them most of it never turns up

[@tjs_welding_and_fabrication]

Gteat tool. Made in my home state. My tool came with a tube of lubricant. I think i have had mine for over 20 years. I used it as a tool post grinder to fix my jet ski impeller. See my vid on it.

[@SteveJordan]

Thanks I will have a look at that later.

[@Steve_Just_Steve]

Why would this be made in your home state then shipped to China and be sold for 1/3 of the MSRP..... It's a cheap knockoff. If it works for you that's great, but should not be called a Foredom

[@tjs_welding_and_fabrication]

@@Steve_Just_Steve maybe the current one is but mine was made in Connecticut over 20 years ago.

[@mk1cortinatony395]

@@tjs_welding_and_fabrication Yes Ive just found this vid and searched for one and it seems China is the manufacturer :(

[@tjs_welding_and_fabrication]

@@mk1cortinatony395 maybe so. I will make a vid on the one i have soon. I know made in Ct.

[@moeni9727]

The price on these seem all over the place. Why are some marked at around £300 and these at £85?

[@SteveJordan]

Because sellers of this Brand name tool have been buying these and then over inflating the prices for resale to make huge profits. Well that's the way I see it.

[@moeni9727]

@@SteveJordan Are you sure its not because these ones might be clones?

[@Steve_Just_Steve]

@@moeni9727 This is 100% a typical Chinese knockoff branded with a stolen US trademark.

[@bobbobbins8913]

@@Steve_Just_Steve Seems like a knockoff to me. Foredom's own website warns of counterfeit products and even gives a serial number that's often used (ma068899). In any case, it's extremely unlikely that a tool that retails for £250 could suddenly be available at what's obviously less than trade price. It's nice to think it might happen, but out in the real world it just doesn't make any sense. Now, I don't mind Chinese tools, I don't even mind Chinese tools that are clearly budget copies of superior products - provided that they're clear about who made them and where they come from. They might be good value for money for people who can't afford or don't need the real thing, and there's a place for that in the market. Like many others, I have cheapo chuckaway copy verniers for quick and dirty work - but when I need to be sure of a dimension I dig out the Mitutoyo. When it moves into making counterfeits, that's another issue entirely - and it's fraud. I'm pretty sure that everyone who watches this and similar channels knows the value and integrity of well-made tools, and it would do us all well to remember that it's people like us who make such tools. They deserve our respect, as much as that Moore & Wright micrometer that you had to scrimp and save for, or that set of Starrett gauge blocks you bought instead of a taking a holiday.

[@Steve_Just_Steve]

@@bobbobbins8913 Not sure why your telling me, that was exactly my point. I just don't think it's right to promote this tool like it's a made in the US product when it is in fact it's a counterfeit with a stolen US trademark.

[@rinklestiltskin]

Predictive text error-should read "Boredom"

[@rinklestiltskin]

Is it true that KZbinrs are related to potatoes?

[@SergeyKarpushev]

Are you sure that it is the real one ? The ones from aliexpress are all fakes. They work not too bad for the price but different from the real thing

[@SteveJordan]

Hi no many people get the wrong idea that the red label models are fakes, but they are not. The red label ones are made for the EU/UK market. The blue label ones are specifically made for the USA and are 110 volt as opposed to the 230 volt red label version.

[@Steve_Just_Steve]

Sergey Karpushev, This is absolutely NOT an authentic Foredom tool made in the USA. It's a complete counterfeit Chinese knockoff. I don't know why Mr.Jordan is misleading people about this.

[@felixf5211]

How are they different from the real thing in their operation? I own 2 of these (SR models) and a US Foredom SR. In what way is the US model better, aside from its pedal?

[@aceroadholder2185]

If you use this tool in your trade, I'd avoid these counterfeit tools... you get what you pay for.

[@SteveJordan]

Mine is excellent quality.I'm so pleased with it. It works great and I've used it so many times.

[@felixf5211]

I have two of these that are used daily. You don't have one, right?

[@jeremydemarco8697]

I got one, and the quality is impressive.. Very solid, smooth, the shaft and the pieces are not even hot after hours not even the motor itself... Anyone can tell me how much is a "real" one,??? I got mine from Amazon for 109$ I know a guy that uses this one 👆 8hours every day for almost 2 years and still like the day one , that's the point that decided me

[@morganlewis2667]

@@jeremydemarco8697 Roll the dice...it's a pig in a poke.

[@zacatecano1986]

Can the chick actually fit a 1/4 bit ?

[@felixf5211]

The 6mm, which is actually 6.5mm, handpiece does fit round 1/4" shanks. In fact, I'm using a 1/4" shank 2" wire wheel right now. It is a tight fit, as 1/4" is 6.4mm, IIRC. Works very well.

[@kathybradbury]

I saw these Chinese counterfeits on EBay today whilst shopping for a flex shaft...was very tempted until I saw to terrible reviews.

[@SteveJordan]

Hi Kathy, Well I'm really pleased with mine. Its is actually the best rotary tool I have owned an used. The quality is outstanding to say the least! Its like with many tools now, who knows where the parts are made? I know this one is made in China, but how do we know whether the genuine ones all have parts made in their home countries. Most manufacturers sub out their work to have parts made in China now. I did see some bad reviews but I'm so pleased it didn't put me off. It has saved me spending three times the price and I have a super high quality tool. It is absolutely fantastic.

[@felixf5211]

I own 2 of these. Never an issue.

[@thechurchofdave]

It's bad enough they copied the American product but they stole the name and the model as well? I don't care if it works or not. I won't buy it based on that. I'd rather have a real one (I have a real one and it's great) or one of the other manufacturers which don't steal the name. I have the Harbor freight one and it is nearly worthless. No torque at all. Barely good enough for light sanding. There is a dremel pendant motor that is 200 bucks an I have yet to try that yet but the reviews seem good. There are lots of other reasonable tools out there so I will never buy from someone who steals a name and model.

[@garypostell5268]

So it’s a knock off version!

[@SteveJordan]

Yes, but very good, though. They seem to sell them on all different sites, but everyone knows they are not genuine ones by the price.

[@jan.catrysse]

Please buy the original genuine part. If you can't afford it, then buy a Dremel.

[@justinsane332]

Just got mine and it's garbage. Doesn't work. Waited two months for delivery. I don't recommend, buy a real foredom, blue sticker.

[@SteveJordan]

I've had mine over a year now. It's still working perfectly. It's excellent.

[@jeremydemarco8697]

I got mine from Amazon for 109 bucks and it works perfectly for almost 1 year

[@justinsane332]

I'm glad you both had better experiences, but I still advocate for supporting the company whose design the Chinese STOLE, and the piece of mind that comes with it. I wouldn't recommend, as stated above, but don't take this comment to heart, I do really hope your motors do not give out, and bring you many hours of creative application. But I still think people should just buy foredom. I'm waiting for my SR now, and will probably do a side by side review.

[@jeremydemarco8697]

@@justinsane332 I understand your point of view, jewelry is (for the moment à hobby) I'm building my little workshop and each cent can be saved. I plan to grow, and of course I will buy real authentic stuff. But I have to say that I went from a dremel to this 👆 and it night/day difference...