CineStill CS41 Film Developing Kit

[@Ricardo-SW]

Admiring your steady hand as you pour into the bottles- I'd have spilled without a funnel :)

[@NathanielBlank]

This man went full hipster which is necessary when working with 35mm film. Great video

[@goldenhourkodak]

A hipster from 2009

[@Mosesybanez]

Lol facts

[@rudycabrera6608]

You are awesome! thanks for the video, I am getting good development results from your help! This is a art that needs to be preserved.

[@lunaartemis5511]

I wish this came up earlier before i had a breakdown because the instructions and other YTs were just confusing me. This helps so much. Thanks. Do i just pore the chemicals back into the same bottles? And does this mean adding more time. (Written instructions are hard to understand in that chenical reuse section)

[@memoirsofhadrian]

Same here. The other videos are waaaay too complicated for a simple procedure.

[@chasedionisio]

Love this kit, I’ve developed many rolls that have came out great!

[@jaidamann8365]

i assume he rinsed out the mixing container and stir wand off camera - to prevent contamination.

[@kcat126]

LOL, I thought (hoped) that he did too. It just reminded be to be hyper aware of my own doing this to my wand, measuring cups, and thermometer.

[@GlazersCamera]

Yes, sorry, Devin had assistants rinsing and drying between shots/chemicals.

[@nestorpool]

I was looking for this comment after watching the video at 03:42 I was afraid...

[@samonthebrink]

came here to say this

[@Bubba-23nineteen]

Love the video but have a question. Can you reuse the developer, blix, and stabilizer? I did notice there is a big color change once it's used once.

[@maxm.2824]

Underrated video.

[@agt5jx87]

Great video and very helpful. Edit out the talent opening the bottles.

[@andreasfort1599]

I need that outfit. I’m not sure if I want to develop my own film right now.

[@johnfmichael]

Also, at 9:42 he says "final agitation" on the blix, but the timer only shows just over 3 minutes, even though he said the agitations for the blix are every 30 seconds for a total of 8 minutes. How can the final agitation occur only 3 minutes into the blix step? Or did I miss something?

[@BENBASIL]

I noticed the same thing, I’m guessing he was still thinking 3:30 like the developer and it was an editing mistake. I doubled checked the instructions and it is in fact a total of 8 minutes, agitating every 30 sec 👍🏼

[@FunkyMonk_96]

How do I clean all my equipment? What do I use to clean up and how do I dispose of any trash if I make a mess? Can I just throw them in the garbage?

[@seboc1]

Use butan spray to prevent oxidation of solutuions. Write the date of mixing on the bottle and developed films.

[@JerryAdam]

Thanks for the video! You should have worn some protection like gloves, etc. though (:

[@GlazersCamera]

Good call!

[@maririnn]

do you just pour the used chemicals back into the containers?

[@goldenhourkodak]

Yes with a funnel

How many films can you run through the same blend

[@henryIRL]

Was curious if distilled water was used? Or would tap water be suffice?

[@darlinstudioco]

how many times can we use the same chemicals? thank u

[@s47industries]

So if I’m just mixing the chemicals and not going use it right then and there or even the same day, do I need to bring up to temp? Or will the chemicals not mix correctly if not at temp? I just want to have them ready for when I do have a roll to develop, and not have to do this whole process when I do want to develop. Like my DF96, ready to go just bring up to temp when I have a roll ready.

[@johnfmichael]

At 0:48, the thermometer only reads about 116 degrees, not quite the 120 degrees stated for the temperature requirement for mixing the developer. Does this mean there is some elbow room regarding the temperatures for mixing the blix and stabilizer as well?

[@goldenhourkodak]

Yes. It just need to be hot enough to dissolve.

[@brookswitta]

are these chemicals re usable?

[@Harrison615]

yes abt 24 times

[@MR-nz6db]

Can I reuse the chemicals?

[@sequentialable12]

Marvellous video

[@thecanadianslimer1379]

I have this bracket and 20onces goes right up to the top of the beaker ??

[@throtol]

How long can the mixed chemicals last before expiring or losing their concentration?

[@bbx2712]

Sir you are the best . THANK YOU

[@ncjr372]

How many ML is the beaker?

[@jimdandy567]

So how long can you store the kit after mixing? How long do the chemicals last?

[@JonathanRuiz]

It develops 24 rolls of film and Cinestill just says it has “Long lasting shelf life” which is not very helpful. If you look online some people say they keep their chemicals for 3 to 6 months but there’s nothing official that I can find.

[@pilsplease7561]

@@JonathanRuiz Ive used chemicals stored in glass bottles for 12 months. Ive had the same E6 kit going for 50 rolls of film for example and its 14 months old and still works like it was made yesterday. So chemicals far outlast what is stated with no quality loss.

[@kcat126]

@@pilsplease7561 Super helpful comments. I just developed my first color roll tonight, after watching this video and reading your comments. Thanks!

[@pixeltx3364]

​@@pilsplease7561 can i save the chemicals i used instead of get rid of them so i can use them again??

[@pilsplease7561]

@@pixeltx3364 you can use them up to like 6 times, If I recall you can do 6 rolls of film per each batch of chemicals or I might be thinking of the E6 kit from a different company. But I think its like 6 rolls per kit.

[@cggg490]

after first four rolls, how much time do you adjust developing time thereafter? I’m bad at math.

[@Dangoldmedia]

Excellent video - thank you

[@lunaartemis5511]

Just about to attempt this for the 3rd time to bow see the thermometer don't even go over 86f. So instead of going out on another shoot (as I f***d my film) and starting this. Should of actually just done coursework and not wasted time. The more you attempt this the more you need to purchase. Cba I give up with film. Taken me 2 years to learn how to unload and load a film without buggering it and now just this. So hard doing all this with Dyslexia and discalcula.. just keep getting it wrong 😪

[@akiray1999]

should I buy the camera or not?

[@out1553]

What camera bro?

[@akiray1999]

@@out1553 don’t want to go all out, looking at the La Sardina for a cheap but not garbage starter

[@KeyLargoDude]

No gloves needed?

[@loriannx143]

Can the washes be reused or only the stabilizer?

[@colerowland8066]

If you buy the powder kit make sure your funnel is completely dry before adding part b of the blix otherwise it will clog and you'll get it everywhere. Don't ask me how I know this.

[@soundistraveling]

So i can reuse al that developer n blix and stabilizer for more film correct?

[@soundistraveling]

And u didnt discard any of it right u saved it for later

[@kylemccourt663]

I am a film photographer of 35 years and a film photography teacher for the past 15. I really want to try this system but the film that came out during this video does not appear to have a clear base, as it normally should. This would be very problematic when actually wet printing the film in the darkroom and trying to color correct by way of dichroic filtration. Is the film density not an issue because it is being scanned instead? I am super curious about this magical system.

[@anthonymiller8979]

I thought all color film (C41 process) has an amber colored base? B&W is usually clear, grey or blue.

[@b6983832]

This is color film. It is not intended for b&w printing, although you can sometimes get decent pictures out of it. Not to multigrade paper though. You can print color images in a darkroom, if your dichroic head in the enlarger is a color head with three filters marked C, M, Y. These can be used for black and white work too. Also, you will need RA-4 paper and chemistry, and equipment for rotary processing will help very much.

[@eliasaguirre1227]

Is this legal in Washington state? I’ve heard the chemicals used can’t be bought.

[@mstrshkbrnnn1999]

This store is in Seattle

[@anthonymiller8979]

No Photo-Flo is needed before drying or is it built into the Stabilizer step?

[@brodie_lienemann]

It’s built in

[@Boskiiino]

🎥🎞🙌🏾

[@jluc002]

12;30 Perfect

[@ncjr372]

Who’s this guy? Does he have Instagram? 😍

[@andyvan5692]

120 degrees for processing?, sure?, as at 100 degrees water BOILS,yet I see no steam!!; just wish you could do a METRIC conversion on these volumes, as since 1966 hardly anyone, esp. in Australia, uses imperial anymore!!

[@DeekonJones]

Water boils at 212 degrees F.

[@rorycowieson5924]

@@DeekonJones and conveniently in Celsius it boils at 100 and freezes at 0. The system every country in the world except like 7 use.

[@DeekonJones]

@@rorycowieson5924 I was simply telling you he wasn’t wrong. Lol

[@karl1137]

If he is referring to 120 degrees F, from what I have read C41 process is 100 to 102 degrees F. This may explain the cloudy negatives.

[@wack.1151]

arent these toxic? shouldnt you wear gloves or something, from what ive heard :(

[@GlazersCamera]

In retrospect, yes, Devin would have benefitted from wearing gloves. That being said, he did not experience any noticeable, adverse effects from not. But still, you should. :D

[@adrianvalella6854]

bad instructions, no gloves or eye protection, did not clean mixing vessel or stirrer, your negs looked bad also

[@dmystify1381]

...do yo have to use a sqeegee thingee...?...asking for a friend..

[@Andrew-tt2xs]

Think you can just hang it to dry just make sure u use a weighted clip at the end so the film doesn’t curl up when drying

[@mampfi]

No you don't need to. Hard water leaves lime stains on the film, to prevent that you could use the sqeegee thingee to get the water off the film. Many people don't use them because it's easy to scratch the film by using them. There are alternatives like to wash the film with distilled water, use a wetting agent or a salad spinner

[@aLittlePal]

the person just drop the film at the end of the process, he does indeed really really care about it. I can totally feel it.