Citroen C4 Picasso air suspension errors C1621, C1196, C118C... Fault finding and repair.

Consider to support my channel and all the hard work put into it at / lmautorepairs
Thank you
Hi
This car came to me wit a problem on the rear air suspension...
After some diagnosis, and test, trace it down to a faulty suspension airbag... but was more to it... much more...
Follow me on this video to find out what was the problem and how to resolve it.
Flux used: NC-559-ASM-UV
rover.ebay.com/rover/1/710-53...
To clean: Isopropyl Alcohol
rover.ebay.com/rover/1/710-53...
Soldering Iron: Temperature controlled soldering station.
rover.ebay.com/rover/1/710-53...
Hot Air Gun Station:
rover.ebay.com/rover/1/710-53...
Desoldering Vaccum Station:
rover.ebay.com/rover/1/710-53...
Hope you enjoy the video.
Any questions or comments put them below.
Like always, thank you for watching!

[@mdsymonds75]

The man who is not afraid to open up modules and work on them. Always a pleasure watching you work.

[@LMAutoRepairs]

😋 Afraid? Never... Thanks, for watching and for your comment!

[@nedalwaleed1583]

You used to be among the top 10 automotive technicians, but I am sure now that you are among the top five in this field.

[@LMAutoRepairs]

I doubt... but thank you for your words! Really appreciated? Thank you for watching and for your comment! 🎄👍🎄👍🎄👍🎄👍🎄👍🎄👍👍🎄👍🎄

[@CarsExposed]

I had the c4 grand Picasso and loved how the pneumatic rear suspension felt but had to replace the bags twice which at the time was very expensive, after replacing the air bags for the second time I decided to convert to a normal coil spring suspension and got Citroen to code the car as no pneumatic system ... good call swapping the mosfet 👍👍👍

[@LMAutoRepairs]

Thanks! 👍👍👍

[@MyName-ez9lv]

Always a pleasure watching masters practice their crafts.

[@LMAutoRepairs]

😊 Thanks! For watching and for your comment!

[@riesmoos]

Great video, good fix. The current sensing is done inside the Wabco module. They use those 2 big copper blocks near the mosFET's in between those big fat pcb traces. They are shunt resistors (often 'Dale' brand). Each shunt resistor has 2 big high current connections and there should always be 2 much smaller pcb traces connected to it (sense lines). You can spot both sense lines at 29:02 on the bottom shunt resistor coming from underneath the shunt resistor. Usually the sense lines lead to a instrumentation amplifier/operational amplifier/comparator (i.e. a small IC). The general idea of a setup like this is to convert a big current into a few milli-volts that can ultimately be 'read' by the main proccessor. Thanks for the upload and have a great 2020 !

[@LMAutoRepairs]

Hi Thank you for watching and for your comment, really appreciated! Have a great 2020! 🎄🎄🎄🎄🎄🎄🎄🎄

[@samihagos628]

@@LMAutoRepairs happy new year Sami from Germany...I wish all the best for you and your family

[@LMAutoRepairs]

@@samihagos628 Thanks! The very best for you too! 👍👍👍👍

[@anzelikozar3649]

Hello Sir-s. Replying here because I see mr.riesmoos has a lot of knowledge to. I am having similar problem. The whole unit costs 720€plus tax. In your video you mentioned that the control unit can cost as much as the relays. Would you maybe care to share where a person can buy this whole unit. Or, what are the relays to buy if one wants to replace them? Than you to both of you. And great and helpful video.

[@raultent6990]

Man you are a Brilliant man who have so much patience !!! Great Mecanic!!!

[@LMAutoRepairs]

👍 Thanks!

[@charliekarting3401]

Very clever bloke, very few garages have these electronic skills, It makes me want to do a electronics night course at college

[@LMAutoRepairs]

😊 Thanks! For watching and for your comment! 🎄🎄🎄🎄🎄🎄🎄🎄

[@alexe610]

AWESOME, Excellent , we learn a lot from you. You are a real true genius (un vrai génie). Many thanks from FRANCE.

[@LMAutoRepairs]

👍👍👍

[@tabamirko468]

Thank you a LOT!!!! you saved my life with this

[@LMAutoRepairs]

Your life! WoW Lol... I know what you mean...that's great... Thank you for watching and for your comment! 👍👍👍

[@sonerschannel3306]

Good stuff. Merry Christmas LM.

[@LMAutoRepairs]

Thanks! Merry Christmas! 🎄🎄🎄🎄

[@petr_car_fix5828]

Thanks for your videos from Russia. You help my study english .My job as mechanic-electrician in BMW dealer is not so interesting.

[@LMAutoRepairs]

Glad you enjoy it! Thank you for watching and for your comment! 👍🎄👍🎄👍🎄👍

[@Ace-Kas]

Awesome video as always, great job!

[@LMAutoRepairs]

Thanks! 🎄🎄🎄🎄

[@isalmankhan1]

Thanks for sharing this valuable information👍 Awesome Fix😎

[@LMAutoRepairs]

Thanks! 👍👍👍👍

[@fritztimm3939]

Happy Christmas from Germany... 🎅👍

[@LMAutoRepairs]

Happy Christmas! Thank you for watching and for your comment!

[@abc-ni9uw]

I throughly love your videos what ever the car/fault

[@LMAutoRepairs]

Hi 😊 Thank you so much! For watching and for your comment! Really appreciated! 🎄👍🎄👍🎄👍🎄👍🎄👍🎄👍🎄👍

[@bundylovess]

Nice repair Luis big thumbs up 👍

[@LMAutoRepairs]

Thanks, for watching and for your comment!

[@pascalc1259]

Great job thk for your vidéo 👍from France 🇫🇷

[@LMAutoRepairs]

😊 Thanks! 👍👍👍

[@juweekhan]

Good video thanks for all your time and effort

[@LMAutoRepairs]

Thank you! 🎄👍🎄👍🎄👍🎄👍🎄👍🎄👍

[@BorisSiber]

Thanks for sharing. May the force be with you :)

[@LMAutoRepairs]

😊 👍👍👍

[@foxsittofox8567]

Great work! Like and Merry Christmas! 🎄

[@LMAutoRepairs]

Thanks! Merry Christmas! 🎄🎄🎄🎄🎄🎄

[@dennispowell7719]

Another great video mate keep them coming 👍

[@LMAutoRepairs]

Thanks! 🎄👍🎄👍🎄👍🎄👍🎄👍

[@nemanjadzombic6101]

Thank you for another great video!!!

[@LMAutoRepairs]

Thank you for watching and for your comment!

[@mrgrumpy5116]

another well done, very interesting, thanks for the videos.

[@LMAutoRepairs]

Thanks Sir! 👍👍👍

[@mariomario3113]

Very very helpfull. Thank you very much. Today resolv this problem 😉

[@LMAutoRepairs]

👍👍👍

[@matushodor4725]

Perfect as always, thanks 👍

[@LMAutoRepairs]

Thanks! 🎄👍🎄👍🎄👍🎄

[@devautoelectronics]

Great ......Merry Christmas Luis

[@LMAutoRepairs]

Thanks! Merry Christmas! 🎄🎄🎄🎄🎄🎄🎄🎄

[@mikimehandziski1045]

Excelent as always. Thanks

[@LMAutoRepairs]

Thanks! 🎄👍🎄👍🎄👍🎄👍🎄👍🎄🎄👍

[@bodgitandleggitgarage]

Nice job mate

[@LMAutoRepairs]

Thanks Leon!

[@marianilea673]

Good job sir like always!

[@LMAutoRepairs]

Thanks! 🎄🎄🎄🎄

[@markobezjak6952]

Thank you for the video. 👍

[@LMAutoRepairs]

Thank you for watching! 🎄🎄🎄🎄🎄🎄🎄🎄

[@mustafajabbar4104]

Thanks for sharing this 🙌

[@LMAutoRepairs]

☺️ 👍👍👍

[@carlamadisonpacoaltamirano4603]

Hola buenas yo te. Go el mismo problema con ese coche y resulta q el mecánico no tiene idea de reparar la centralita la verdad estoy arto del coche por el tema de la suspensión, pero la verdad admiro el talento q tiene para solucionar este tío de problemas

[@didierkoka9778]

Good job Sir 👍🏽

[@LMAutoRepairs]

Thanks! 🎄🎄🎄🎄

[@benjaminlevi7792]

Good job and useful info thanks

[@LMAutoRepairs]

Thanks! 🎄🎄🎄🎄

[@hublebubble]

Hi where is the compressor relay located citroen c4 picasso 2008, love your videos very helpful thanks

[@philclements6314]

Hats off to you, true fault finding skills there. I liked the subtle cussing of Citroens, we have one too and it regularly throws up silly little quirks that fault readers cannot totally pinpoint. Subscribed :)

[@LMAutoRepairs]

😊 Yes they do... they can keep you quite busy... Thank you for watching!

[@svpiggybank]

Great thanks. I have a bunch of these problems on my c4 I think it is connected to that blue wire on the fuses on top of the battery. Where does that go to can I run an alternate I have checked the loom as far as I can. Keep up the good work jim

[@mohamadmirza31]

Where is the relay combresor . located?

[@ciprianfrancu5985]

Hello, congratulations! the video and the content were done in a very professional way. I have a question, my Picasso is having a strange behavior ... some time is inflating and deflating at the same time the pneumatic system ... resulting in a drop-down .. sometimes for days, everything runs ok ... I wonder if a complete calibration of the pneumatic suspension + a clean-up of the height sensor will solve somehow the problem? As a software solution, I use DIAGBOX9.68. Any particular things to keep in mind ... when I will start the procedure? Any advice is highly appreciated.

[@mazi16v]

Merry xmas m8

[@LMAutoRepairs]

Merry Christmas! 🎄🎄🎄🎄🎄🎄🎄🎄

[@astroboy2astroboy247]

Exelente amigo 👏👏👏👏👏

[@LMAutoRepairs]

Obrigado! 👍🎄👍🎄👍🎄👍🎄👍🎄

[@ahmednaseer6769]

Great job

[@LMAutoRepairs]

Thanks! 🎄👍🎄👍🎄👍🎄👍🎄👍🎄

[@MrFOXMAROC]

nice work

[@LMAutoRepairs]

Thanks!

[@DDICyber]

i think the input resistor works only as a diode or sort of a fuse like in a dc input from a laptop and the first one you can bridge them in the most cases

[@murgasse2854]

Excellent video and very instructive. Friend, can you tell me the name of the relay model, because I have the same problem as you

[@Parknest]

I had problems with the pneumatic rear air suspension on mine. I came to the conclusion that it was the compressor (the thick end of £1,000 from the dealer. I wasn't going to take a chance on a used or a recon part) so I decided to do a coil spring conversion which cost me less than £200 in parts. I disabled the suspension ECU and the auto height correction in Diagbox and removed fuse F10 (15A) in the glovebox which is for the auto height correction to stop any error messages from appearing on the display. It has been fine ever since but it will generate a couple of fault codes.

[@LMAutoRepairs]

A lot of people does that... Thank you for watching and for your comment!

[@sumeda36]

The compressor relay fault was on voltage. I have had the same problem. It's a case of new battery and new compressor.

[@mohamedbherey8652]

Really nice

[@LMAutoRepairs]

Thanks! 👍👍👍👍

[@soldiers303]

Have you worked on any blutec mercedes? I have an issue where the adblue counter wont reset and its now saying 500 miles left. It’s topped up and indicates that the system is full but counter wont change, just keeps dropping. Any way to fix this?

[@leemckenna1978]

Excellent work again who do you use for your wiring diagram as the ones you use in your videos look a lot better than the ones I use at work

[@LMAutoRepairs]

I use a different stuff... all depends on the car I am working on... Thank you for watching and for your comment!

[@georgeberrill4834]

Nice job mate. You certainly know your way round these nightmares. My 57reg GPC4 feels hard on the rear but the ride is good - the compressor works for about 4 or 5 seconds on schedule and it does what it should, but on roads with a poor surface the back end feels hard. What do you think it might be? It had new bags last year so I think they are ok. Cheers.

[@AndysEastCoastAdventures]

They are known for being hard on the rear, makes them a good tow car though.

[@martincheer2008]

The wheels are jacked up, so it’s on its highest level already cutting out with the sensor

[@cood22]

Great job. How did you manage to desolder the wide connectors? I have a similar desoldering station, but I didn't have a tip wide enough that fits over those connectors.

[@LMAutoRepairs]

Vacuum de soldering station... Links in the video description... Thank you for watching and for your comment!

[@anassboushabi378]

Smart jobbbb. Greatttt

[@LMAutoRepairs]

Thanks... for watching and for your comment! 🎄👍🎄👍🎄👍🎄👍🎄👍🎄👍🎄👍

[@RAPZATOITZ]

Hi mate can you pls tell me or share a link where did you buy the parts pls

[@yawmiyat-ismail]

مفيد

[@duncanmartin8965]

Hi ,I put some weight in back of car , hydrolic suspension went up but now it won’t go down . What’s the problem with this ? Both airbags are solid full of air. Plugged in diagnosis computer and states fault codes C1196

[@Estemugue]

Hello I dont speak english, sorry, but I have a question for you. my picasso has got one problem, diagbox says C1621 Relay compressor and I dude. Where is the relay in compressor or pneumatic unit control? The people says in compressor but I dude. If I put a new compressor the problem is solved, after is necessary diagbox? Or is not necessary? Mi compressor has got 162.800 km. Thank you very much.

[@StationGarageSt]

Well done......many a "good" car goes to scrap for this sort of prob!

[@LMAutoRepairs]

Thanks! For watching and for your comment!

[@mohamadmirza31]

Hello, I have a cetarwen c4 picaso. Sometimes the servise subsension light flashes fatly, sometimes intermittently. The car was checked in several workshops and they did not find a malfunction. Some said the compressor should be changed. Some said the height sensors should be changed. Some said the electronic mind. Only at the top there is a code 1196, but it is not permanent. Is this a permanent malfunction caused by an industrial error in all cars of this model?

[@nelsonpinto625]

Olá, vídeo excelente! Tenho um C4 GP e estava a dar problemas de suspensão, foi trocado compressor e as molas pneumáticas mas mesmo assim o problema continua, por vezes trabalha normalmente é noutras tantas vezes não arranca o sistema. Vou tentar ver a placa se será o mesmo problema. Obrigado pelos vídeos! Abraço

[@LMAutoRepairs]

👍👍👍

[@aPicaMata]

Boas, teve que substituir a placa?

[@svpiggybank]

Great thanks. I have a bunch of these problems on my c4 I think it is connected to that blue wire on the fuses on top of t he battery. Where does that go to can I run an alternate I have checked the loom as far as I can. Keep up the good work jim

[@LMAutoRepairs]

If I recall correctly, it is a feed to the ABS/ESP... 👍👍👍

[@steves7973]

Good repair, these cars are very quirky, the least thing can throw up a fault. They need a good battery as a failing battery can throw up intermittent and random faults. The button below the height adjuster in the rear switches off the air suspension for maintenance and lights up with a red indicator. Citroen had a recall for the airbags for the C4 and replaced them for free but I think the campaign will be closed now.

[@LMAutoRepairs]

Thank you for watching and for your comment, appreciated! 🎄👍🎄👍🎄👍🎄👍🎄👍

[@mrautoexpert9417]

Bro plz show us the checking proceger ecu.or ecm please bro with multimeter.

[@jeffp0tter]

Thanks

[@LMAutoRepairs]

☺️ Thank you so much! Really appreciated! 👍👍👍

[@nevzatkayhan5278]

can you help me thank you in advance

[@nevzatkayhan5278]

​@@LMAutoRepairs can you help me thank you in advance

[@4642mati]

Super 👌 film

[@LMAutoRepairs]

Thanks! 🎄🎄🎄🎄

[@electronic7979]

👍👍👍

[@LMAutoRepairs]

Thanks! 🎄👍👍🎄👍🎄👍🎄👍🎄👍🎄

[@lourdesaltamirano83]

Hola amigo ,sabe yo tengo el mismo problema con la centralita de suspensión pues el coche se quedó abajo del todo y no funciona el compresor q es lo q arreglaste en la centralita para q vuelva a funcionar ,pues no sé si cambiarle por unos muelles por q al final de me dio mucho gasto este punto coche gracias y saludos

[@dammmziik9034]

hi you are doing always Good Job. i want to buy one of this devices but i don't know which. my question is when you should chose one of them wich one?

[@dammmziik9034]

autel Elite or artipad

[@alonze2005]

Good job as allways :) but if I vere You, I would suggest client to change it to simple springs, there are many kits on sale. It costs about 70€ for both sides, then just disable it from from BSI. Then problem SOLVED FOREVER. And if you compare ride quality and comfort, there are NO difference. Merry Xmas!

[@LMAutoRepairs]

Thanks! For watching and for your comment!

[@neilmurphy845]

So why do they put them in

[@alonze2005]

@@neilmurphy845 to make so aditional money ;)

[@neilmurphy845]

@@alonze2005 ya I was thinking that to some extent

[@steves7973]

You will lose self leveling and height control, I used to own one of these and towed a caravan with it, terrific car.

[@javierizuel8663]

Hi @LM Auto Repairs, I have the same problem, wouldn't you by any chance have the ID of the mosfet to order them?. Thanks and congratulations for your video, very explanatory!!!

[@LMAutoRepairs]

Hi Never took that information at the time. Sorry... Can you not read on yours?

[@AndysEastCoastAdventures]

Did the ECU require a new mosfet after all or did swapping the 2 reworking fix the problem? Dry joint somewhere possibly?

[@LMAutoRepairs]

No... it did not, at least I was not asked to look at it again...🤞

[@hublebubble]

Hi, where is the compressor relay located, love your videos very helpful thanks

[@LMAutoRepairs]

Inside the module... as shown.. Thank you for watching and for your comment!

[@hublebubble]

Hi thanks for your answer you say inside the module is that where the compressor is or ECU on floor behind front seats thanks again

[@billhoggy4461]

Hi great video have you got the link for the air bags

[@LMAutoRepairs]

Not anymore... Sorry... 👍👍👍

[@mohautobelabbes8819]

Good jop man💯💯💯

[@LMAutoRepairs]

Thanks! 🎄👍🎄👍🎄👍🎄👍

[@linasas4992]

Hi. Greatest video a found so far... How is this citroen going today? Does error p1621 reapeared after some time? I have bought same car and sometimes facing same error. It usually come in the morning, but after driving a bit and shuting engine down, compressor kicks in. And error disappear for rest of the day. I have a question. Do you remember exacr number of mosfet? I would like to resolder that one, which is responsible for motor. Thanks

[@LMAutoRepairs]

Hi It never came back... so...I guess still good... I can't remember those details... sorry... Thank you for watching!

[@linasas4992]

@@LMAutoRepairs well. i have read in one forum, that this error may be solved, by rechecking fuel pump. change silica gel and cleaning/oiling air pump once every few years... anyway. it would be great to know relay part number so i could order it before starting repairs.

[@WereReallyRelayCamping]

low batteries cause all kinds of errors, one car i had would put up ABS fault on the display when i braked in cold weather as all the 4 brake lights at the back suddenly coming on would cause a quick voltage drop and scare the ecu.....

[@LMAutoRepairs]

Absolutely! I have many videos on that... Thank you for watching and for your comment!

[@SerDanny]

Hi Very interesting work you done there. I've changed myself the air spring as well but somehow I've messed-up the height sensor values and now error shows on screen. Car runs fine suspension its self levelling itself no problem but annoying error on the screen it's so annoying. Do you know what values may me going there on the height levelling ? Thanks

[@LMAutoRepairs]

The calibration needs to be done on a flat bed... There is usually certain procedures that need to be followed in order to calibrate everything correctly... There is some documentation out there... 👍👍👍

[@SerDanny]

@@LMAutoRepairs Thanks . I've done it last night . Now the height sensor is programmed properly. Everything working fine.

[@rpq7889]

Hi from Spain! Did you fix the problem?..... I have the same problem since 4 years and havent already fixed. Please give me some clues or information where I can see how to proceed Thanks in advance!

[@nevzatkayhan5278]

hello from sweden my question is the same height calibration can you help me laxia program wants millimetric calculation i don't know i couldn't do it thank you for your help citroen c4 grand picasso 2008-modell

[@MrLukelike3]

I'm having similar issues with my Citroen c4 picasso however after watching you find your leak I cannot relate to this issue as last night my car raised completely and stayed raised until this morning when I went for a drive and then the suspension fault come on again and it wouldn't raise. If I had a leak them surely the car would would've lowered over night?

[@LMAutoRepairs]

I would say so... You might have a different problem... That's the beauty of some how follow the video, as you can find something that leads you to a different outcome... 👍👍👍👍

[@techstuff786]

Hello My cars throwing up c1621 code for compressor relay... At first the car was completely down airbags flat.. i tested the bags with compressed air and saw leaks in the bags so i have replaced the bags now for new ones but every time i try to pressurise the system or try and fill lh spring or rh spring, i get error c1621. Is the relay faulty and is it located in the ecu? If i buy new ecu will it work? Please reply.. desperate for help!!!!

[@LMAutoRepairs]

I can't really say it will work without checking it... It difficult to give an informed advice based just on what you are explaining...

[@mohamadmirza31]

Please, is it necessary to change the oil for the semi-automatic gearbox, knowing that in the maintenance book it is written that it is for life?

[@LMAutoRepairs]

I would change it... 👍👍👍

[@JonTwycross]

Great video, love the detail you go into . The only thing I couldn’t see in the video is how the airbags disconnect from the air line? Do you need a special tool to disconnect the air line?

[@LMAutoRepairs]

Hi No, it is just a push fit type connector... really easy... Thank you for watching and for your comment!

[@JonTwycross]

You have literally helped me figure out all the problems with my wife’s car. The troubleshooting steps really helps and to hear your dialogue when you are working stuff out, this steps help piece the puzzle together.

[@LMAutoRepairs]

@@JonTwycross Hope you can get it sorted... and make your wife happy...😋 👍👍👍👍

[@JonTwycross]

When you remove the pipe, is there a collar you need to pull out or anything? I am under the car right now and can not get the line out of the existing air bag

[@JonTwycross]

So, there is a little collar which releases the hose and on mine they had perished. So I had to carefully cut round the valve with a junior hacksaw and then pull it out the casing and then use pliers to remove the retaining clip. After that it was simple.

[@gowrymanokaran866]

My car citroen c4 picasso 2007 How to do manual

[@Autodiagnosistz]

Hi friend, your video helps me a lot on my daily work.god bless you I'm from East Africa would like to know how i can get ECU pin out, wiring diagram software for Japanese cars.or just tell me the software name then will try to look.thanks

[@LMAutoRepairs]

Hi Unless you go for the OEM tools there is really no Japanese cars software as a such... There is tools that work better or have better coverage on Asian cars... just research... For diagrams, there is plenty of choices... you can again look for the OEM stuff, or go for things like Autodata, HGS, etc... Hope that helps. Thank you for watching and for your comment!

[@Autodiagnosistz]

@@LMAutoRepairs so how can I get exactly ECM pin out and wiring diagram for Japanese cars.. In Africa we mostly use used spare parts not easy to get a dealer for OEM staff. Some times works become so hard without no wiring diagram..plz assist

[@dimitarstefanov9825]

Hi, I've got some problems with my citroen C4 navigation start and after couple of seconds restart again. On my autel comes code : B132B (12) B162C(12) B1418(00) Can you please give me some help about this codes Thank you

[@bigbarrysimpson2861]

Can see on the video the mossefett had a pin hole in it that was the broken one by the looks of thinks magic smoke came from that

[@LMAutoRepairs]

Possibly... Thank you for watching and for your comment!

[@imkirbo3094]

Lets face it, buying an 11 year old Citroen with air suspension is asking for trouble.

[@LMAutoRepairs]

That's also very true...🤪 Thank you for watching and for your comment!

[@neilmurphy845]

True

[@receitascommusicabyricardo7589]

My compressor sometimes kicks in, sometimes don't. I have compressor relay error code. Where can i find this relay, my friend? Please, help me. Hug from Portugal.

[@LMAutoRepairs]

As per the video... the relay on this model refers to the module itself... as the relay is built in... The module, if I recall correctly, is underneath the carpet on the rear, behind the front seat passenger side... driver side for you in Portugal... But, I am not sure if there is different versions where the relay and electronics are different, you need to investigate yours... 👍👍👍

[@donalfitzpatrick7324]

My 2008 c4 grand picasso had the airbag suspension spent a fortune replacing airbags only for the compressor to die 2 weeks later. Compressor was 800 euros without labour i got the full conversion done all in for 600 and never looked back still driving it how many years later

[@LMAutoRepairs]

👍👍👍

[@RAPZATOITZ]

Hi can you pls send or share me a link where did you both your the pair of Air suspension pls

[@LMAutoRepairs]

eBay if I recall correctly... 👍👍👍

[@marcinolszewski2220]

I would not recommend original ones . IMHO better go to good quality spare ones, like Arnott -Contitech. Ebay ones last only 3 years for me. Already fit some from Aerosus.

[@LMAutoRepairs]

👍👍👍

[@tom132111]

Hi, I have a problem with the Citroen C4 Picasso - it displays the error U1224 but I do not have a diagnostic computer, only the OBD II application, the car does not rise - the compressor does not turn on - what could this be the reason

[@LMAutoRepairs]

It can be many things... You need to get it properly scanned, and possibly look at some live data to understand what might be wrong... Anything I would suggest, would be pure guess work... Thank you for watching!

[@nevzatkayhan5278]

Hello, ! have a Citroen C4 Grand Picasso 2008 model. Can you tell me how many millimeters the rear suspension height should be? Thanks for your help H1M-R1 Merhaba, ! Citroen C4 Grand Picasso 2008 modeline sahip olmak. Arka süspansiyon yüksekliğinin kaç milimetre olması gerektiğini söyleyebilir misiniz? Yardımınız için teşekkürler H1M-R1

[@nevzatkayhan5278]

hello my car citroen c4 grand picasso 2008 how many mm should the rear suspension body height be? right and left side 100mm? Or is it 115mm can you help me thanks

[@LMAutoRepairs]

Hi I am not sure of the exact measurement on that one... I guess is not imperative to get it spot on... so, as far as the car seats nicely, should be ok... I can try to look for some information on my systems, but can't promise anything... 👍👍👍

[@nevzatkayhan5278]

Thank you, I hope you can find the dimensions. Before connecting to the diagbox machine, I need the height mm measurements. Can you help me, thank you very much.

[@nekoizmase9969]

Maybe bad soldering too

[@LMAutoRepairs]

Possibly... Thank you for watching and for your comment! 🎄👍🎄👍🎄👍🎄👍🎄👍🎄👍

[@neilmurphy845]

Why do they only use rear airride suspension it seems a bit pointless

[@user-zc7qb9dq6x]

To compensate for cargo in the trunk and rear passengers.

[@neilmurphy845]

@@user-zc7qb9dq6x ya I sapose that makes sense

[@cal638]

I wish my electronics skills were as good as yours, gon watch mor of ur electronic vids..why ur soddering station so big

[@LMAutoRepairs]

Hi Just a normal soldering station really... Is a temperature controlled one, you need it to do certain jobs... Thank you for watching! 👍👍👍

[@t0nito]

Congrats man, you've come a long way since we defeated that stupid audio CDs copy protection remember? :P Those were good times :) I love watching these "find and fix" videos at a component level. Part swapping is for pussies.

[@LMAutoRepairs]

If I remember... lol Really good old times... Scroll through my channel... there is loads of that type of repairs... "Part swapping is for pussies" Lol

[@mudassar34]

Phew what a mission and a useless bit of kit if they can fit springs on the front why not on the rear worst french invention ever especially if it goes wrong grrrr

[@LMAutoRepairs]

Thank you for watching and for your comment!

[@wingmaster012]

Great repair. Everyone Else would have shred the whole Car with the engine running while drinking a Beer.

[@LMAutoRepairs]

🤣🤣🤣 Thank you for watching and for your comment!